Festo EHAM-H1-20-L2-80 Manual de Usario

Festo Niet gecategoriseerd EHAM-H1-20-L2-80

Lee a continuación 📖 el manual en español para Festo EHAM-H1-20-L2-80 (2 páginas) en la categoría Niet gecategoriseerd. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/2
Montageanleitung (de)
749 997 / 2010-03NH
†‡
Adapterplattenbausatz
EHAM-H1-...-L2-...
Festo SE & G Co. K
Postfach
D-73726 Esslingen
++49/(0)711/347-0
www.festo.com
1. Teileliste
14566d_1
2 Adapterbausatz
EHAM-H1-...-L2-...
Bestimmungsgemäß dient der Adapterbausatz 2 dazu das Dreh-Hub-Modul
EHMB 1 mit der Achse EGC/DGC 3 zu verbinden.
Der Adapterbausatz 2 besteht aus 2 identischen L-förmigen Adapterplatten.
2. Montage
14566d_3
Platzieren Sie die
Zentrierhülsen (B) am Dreh-
Hub-Modul 1.
Befestigen Sie eine der
Adapterplatten 2 am Dreh-
Hub-Modul 1 mit den
Schrauben (A).
Halten Sie das zulässige
Anziehdrehmoment MA ein.
14566d_2
Platzieren Sie die
Zentrierhülsen (D) am
Schlitten der Achse 3.
Befestigen Sie die andere
Adapterplatte 2 an der
Achse 3 mit den
Schrauben (C).
Halten Sie das zulässige
Anziehdrehmoment MA ein.
Platzieren Sie die Zentrierhülsen (F) in der unteren Adapterplatte 2 die
bereits an der Achse 3 montiert ist.
Platzieren Sie die obere Adapterplatte 2 die bereits am Dreh-Hub-
Modul 1 montiert ist, an der unteren Adapterplatte 2 wie abgebildet.
Drehen Sie die Schrauben (E) fest.
Halten Sie das zulässige Anziehdrehmoment M
A ein.
Info
Bevorzugt soll das schwerere Teil (hier der EHMB 1) auf den Adapter des
leichteren Teils (hier EGC/DGC 3) aufgesetzt werden, wie abgebildet.
Beachten Sie, dass wenn die Adapterplatten 2 anders herum montiert
werden, ein Monteur mehr erforderlich ist um das schwerere Teil (hier
der EHMB 1) zu stützen.
3. Schraubengrößen und Anziehdrehmomente MA
1)
1) Toleranzen für nicht tolerierte Anziehdrehmomente M A
MA
> 1 Nm: ± 20%
A
B
EGC DGC EGC DGC EGC DGC
80 25 80 25 120 40
M
A1)
[Nm]
6 4x 4x
4x
2x 2x
2x
6 4x 4x
10 4x
2x 2x
6 4x 4x
10 4x
2x
2x
F Zentrierhülse
ZBH-7 2x
ZBH-9
2 Bausatz
3 Achse
M5x14 - 8.8
M5x25 - 10.9
M6x30 - 10.9
E Zylinderschraube nach DIN 912
ZBH-7
25-L2-8020-L2-80
EHAM-H1-
B Zentrierhülse
ZBH-9
D Zentrierhülse
ZBH-9 2x
EHMB
20 25
A Zylinderschraube nach DIN 912
1 Dreh-Hub-Modul
32-L2-120
32
C Zylinderschraube nach DIN 912
M5x14 - 8.8
M5x16 - 8.8
M6x16 - 10.9
2
2
C D
F
E
E
A
1
B
2
3
D
2
C
3
1
2
2
E
F
E
Assembly instructions (en)
749 997 / 2010-03NH
†‡
Adapter plate kit
EHAM-H1-...-L2-...
Festo SE & G Co. K
Postfach
D-73726 Esslingen
++49/(0)711/347-0
www.festo.com
1. Parts list
14566d_1
2 Adapter plate kit
EHAM-H1-...-L2-...
The adapter kit 2 is intended for use for combining the rotary lifting module
EHMB 1 with the axis EGC/DGC 3.
The adapter kit consists of 2 identical L-shaped adapter plates. 2
2. Mounting
14566d_3
Place the centring
sleeves (B) on the rotary
lifting module 1.
Fasten one of the adapter
plates 2 to the rotary lifting
module 1 with the
screws (A).
Observe the permitted
tightening torque MA.
14566d_2
Place the centring
sleeves (D) on the slide of
the axis 3.
Fasten the other adapter
plate 2 to the axis 3 with
the screws (C).
Observe the permitted
tightening torque MA.
Place the centring sleeve (F) in the lower adapter plate 2, which has
already been mounted on the axis 3.
Place the upper adapter plate 2, which is already mounted on the rotary
lifting module 1, on the lower adapter plate 2 as shown.
Tighten the screws (E).
Observe the permitted tightening torque M
A.
Information
The heavier part (here the EHMB 1) should preferably be placed on the
adapter of the lighter part (here EGC/DGC 3), as shown.
Please note that when the adapter plates 2 are mounted the other way
around, one more installer is needed to support the heavier part (here
the EHMB 1).
3. Screw sizes and tightening torques M
A
1)
1) Tolerance for non-toleranced tightening torques M A
MA
> 1 Nm: ± 20%
A
B
EGC DGC EGC DGC EGC DGC
80 25 80 25 120 40
MA1) [Nm]
6 4x 4x
4x
2x 2x
2x
6 4x 4x
10 4x
2x 2x
6 4x 4x
10 4x
2x
2x
32-L2-120
32
C Socket head screw as per DIN 912
M5x14 - 8.8
M5x16 - 8.8
M6x16 - 10.9
EHMB
20 25
A Socket head sc rew as per DIN 912
1 Rotary lifting module
E Socket head screw as per DIN 912
ZBH-7
25-L2-8020-L2-80
EHAM-H1-
B Centring sleeve
ZBH-9
D Centring sleeve
ZBH-9 2x
F Centring sleeve
ZBH-7 2x
ZBH-9
2 Kit
3 Axis
M5x14 - 8.8
M5x25 - 10.9
M6x30 - 10.9
2
2
C D
F
E
E
A
1
B
2
3
D
2
C
3
1
2
2
E
F
E

Especificaciones del producto

Marca: Festo
Categoría: Niet gecategoriseerd
Modelo: EHAM-H1-20-L2-80

¿Necesitas ayuda?

Si necesitas ayuda con Festo EHAM-H1-20-L2-80 haz una pregunta a continuación y otros usuarios te responderán




Niet gecategoriseerd Festo Manuales

Niet gecategoriseerd Manuales

Últimos Niet gecategoriseerd Manuales