Festo PAML-CP-186-HP3-G114 Manual de Usario

Festo No categorizado PAML-CP-186-HP3-G114

Lee a continuación 📖 el manual en español para Festo PAML-CP-186-HP3-G114 (2 páginas) en la categoría No categorizado. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/2
PAML-CP/-MK-186
Sub-base/Module connector
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Deutschland
+49 711 347-0
www.festo.com
Assembly instructions
8161951
2021-10b
[8161953]
Translation of the original instructions
© 2021 all rights reserved to Festo SE & Co. KG
1 Applicable documents
All available documents for the product
è www.festo.com/sp.
2 Safety
2.1 Safety instructions
–Only use the product in its original condition without unauthorised modifica-
tions.
–Only use the product if it is in perfect technical condition.
–Take the weight of an individual device or a service unit into account.
Dependent on the design, a mounted service unit can weigh more than 100 kg.
–Under intended use the surface temperature may reach 60 °C. Allow the device
to cool down before working on it.
–Make sure the mounting surface is sufficiently strong for the maximum forces.
–Only use suitable mounting components.
–Mount the individual device or the service unit only on flat surfaces.
2.2 Intended use
–The sub-base PAML-CP serves as an adapter for the pneumatic connection and
for pipe mounting for in-line installation of service units.
–The module connector PAML-MK is used to connect two service units of the
same size.
2.3 Training of qualified personnel
Work on the product may only be carried out by qualified personnel who can eval-
uate the work and detect dangers. Personnel must have the relevant mechanical
training.
3 Additional Information
–Accessories è www.festo.com/catalogue.
4 Product Range Overview
4.1 Scope of delivery
1
2
3
4
5
Fig. 1: Sub-base PAML-CP
1
Front plate (1x)
2
Rear plate (1x)
3
Screw (8x)
4
Washer (8x)
5
O-ring (2x)
6
7
8
9
Fig. 2: Module connector PAML-MK
6
Screw (2x)
7
Front plate (1x)
8
O-ring (1x)
9
Rear plate (1x)
4.2 Not in scope of delivery
10 11
Fig.3
10
Electrical pressure regulator (1x)
PREL-186
11
Micro filter (1x)
PFML-186
5 Assembly
5.1 Mounting the connecting plates PAML-CP
1
2
3
4
5
12
Fig.4
1. Orient the front plate and the rear plate so the stamp number on the1 2
sub-base corresponds with the stamp number on the housing (1 to 1 and 2 to
2) and the mounting thread for wall mounting points to the rear.aB
2. Insert the O-rings in the slots provided.5
3. Position the front plate and the rear plate .1 2
4. Fasten the front plate and the rear plate to the service unit using four1 2
screws and four washers . Tightening torque: 27 Nm ± 15% 3 4
5. Comply with the maximum screw-in depth for the pipe connection.
ISO 228 Max. screw-in depth [mm]
G1/2 12
G1 1/4 20
G1 1/2 22
G2 24
G2 1/2 26
5.2 Assembly of the module connector PAML-MK
6
7
8
9
13
Fig.5
1. Note the flow direction from 1 to 2. The numbers on the product housingaC
serve as orientation.
2. Insert the retaining screws through the holes in the front plate .6 7
3. Place the seal between the service units.8
4. Place the front plate and the rear plate in the slots of the service units.7 9
5. Tighten the screws . Tightening torque: 40 Nm ± 25% 6
5.3 Wall mounting
The M12 threads on the sub-bases and module connectors can be used to mount
individual devices or service units on the wall or a machine frame.
The grid dimension width for distributor block PMBL-186-HP3 is 93 mm.
The grid dimension width between the sub-bases and module connectors is
186 mm as standard, and the hole spacing is 145 mm in height.
14
Fig.6
•Fasten all sub-bases and module connectors with two screws M12 each.aD
The screw-in depth must be at least 15 mm and maximum 18 mm. Maximum
tightening torque: 42 Nm
6 Disassembly
1. Depressurise the system.
2. Check the surface temperature of the device. If necessary, let the device cool
down.
3. Remove the existing service unit string.
7 Technical data
PAML -CP -MK
Operating pressure [MPa] 0 … 5
[bar] 0 … 50
[psi] 0 … 725
Temperature of medium [°C] +5 … +60
Ambient temperature [°C] +5 … +60
Tab. 1: Technical data

Especificaciones del producto

Marca: Festo
Categoría: No categorizado
Modelo: PAML-CP-186-HP3-G114

¿Necesitas ayuda?

Si necesitas ayuda con Festo PAML-CP-186-HP3-G114 haz una pregunta a continuación y otros usuarios te responderán


No categorizado Festo Manuales

Festo

Festo SIEH-M18B-PS-K-L Manual de Usario

25 Octubre 2024
Festo

Festo SIEF-M12B-PS-S-L Manual de Usario

25 Octubre 2024
Festo

Festo VOFC-LT-M32C Manual de Usario

25 Octubre 2024
Festo

Festo DGSL-20-150-EA Manual de Usario

25 Octubre 2024
Festo

Festo DGSL-10-50-Y3A Manual de Usario

25 Octubre 2024
Festo

Festo EPCC-BS-60-400-5P-A Manual de Usario

25 Octubre 2024
Festo

Festo EPCC-BS-32-25-3P-A Manual de Usario

25 Octubre 2024
Festo

Festo EPCC-BS-32-125-3P-A Manual de Usario

25 Octubre 2024
Festo

Festo SFAH-50B-Q6S-PNLK-PNVBA-M8 Manual de Usario

25 Octubre 2024
Festo

Festo SFAM-62-3000L-M-2SA-M12 Manual de Usario

25 Octubre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024