Frigidaire FFRA052ZA1 Manual de Usario

Lee a continuación 📖 el manual en español para Frigidaire FFRA052ZA1 (4 páginas) en la categoría aire acondicionado. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/4
READ BEFORE INSTALLING UNIT
BT Window Mounting (5,000 BTU)
1
Installation Instructions
Before installing, the top rail must be assembled on the unit.
Top Rail Hardware Qty.
4
1
Top Rail Drill (If pilot holes are needed)
7
1
Mounting Hardware Qty.
2
(For Vinyl-Clad windows)
NOTE:
the best way to store unit during winter, or when not
in use.
2
(For Wooden windows)
Top Rail
Fig. C
weather seals 5
window sash seal foam 1
be exposed:
Carefully read the installation manual before beginning.
INSTALLATION WARNINGS AND CAUTION
Fig. B
Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit over an extended
period of time.
66129926560
NOTE: Top Rail and Side Panels at each side are oset to provide the proper pitch to the rear. This is
necessary for proper condensed water utilization and drainage. If you are not using the Side Panels for any
reason, this pitch to the rear must be maintained!
Place unit on floor, a bench or a table. There is a Left and Right side Filler Panels - be sure to use the proper
panel for each side. When installed, the flange for securing the panel in place to the window sill will be facing
into the room.
A. Hold the side Panel in one hand and gently pull back the center to free the open end. See FIG. 1.
B. Slide the free end “ ” section of the panel directly into the cabinet as shown in FIG. 2. Slide the panel down. Be T
sure to leave enough space to slip the top and bottom of the frame into the rails on the cabinet.
LEFT + RIGHT FILLER PANEL ASSEMBLY
FIG. 2 FIG. 3FIG. 1
C. Once the panel has been installed on the side of the cabinet, make sure it sits securely inside the frame channel by
making slight adjustments. Slide the top and bottom ends of the frame into the top and bottom rails of the cabinet. See
FIG. 3.
D. Slide the panel all the way in and repeat on the other side.
2
Installation
“T” section Top Rail
Bottom Rail
Cut the seal foam(adherent type) into proper length. Then stick the seal foam at the lower part of the window frame.
Your air conditioner is designed to install in standard double hung windows with opening widths of 23 to 36 inches
(584 mm to 914 mm) (FIG. 4A & FIG. 4B)
Lower sash must open sufficiently to allow a clear vertical opening of 14.5 inches (368 mm ). Side louvers and the rear of
the air conditioner must have clear air space to allow enough airflow through the condenser, for heat removal. The rear
of the unit must be outdoors, not inside a building or garage.
SEAL FOAM
Fig. 4A
Wooden Windows
Fig. 4B
Vinyl-Clad Windows
INNER
WINDOW SILL INNER
WINDOW SILL
INTERIOR
WALL
If the air conditioner is blocked by Storm Window, add wood as
shown in FIG. 5, or remove storm window before air conditioner
is installed.
If Storm Window Frame must remain, be sure the drain holes or
slots are not caulked or painted shut. Accumulated Rain Water
or Condensation must be allowed to drain out.
Storm Window: FIG. 5
Board
thickness as
required, for
proper pitch to
rear, along
entire sill.
Fasten with
nails or screws.
Storm window
frame or other
obstruction.
SASH
1-1/2” min
(38 mm)
14.5" min
(368 mm)
14.5" min
(368 mm)
SEAL FOAM
Installation
Extend the side panels out against the window frame (FIG. 7A for wooden windows), (FIG. 7B for Vinyl-Clad
windows).
Place the frame lock between the frame extensions and the window sill as shown (FIG. 8A for wooden
windows), (FIG. 8B for Vinyl-Clad windows).
FIG. 8A
A: For wooden windows:
NOTE:
Before driving the screws, use a drill to drill 5 holes through the holes in the frame lock and frame extensions
B: For Vinyl-Clad windows:
FIG. 8B
3
FIG. 7BFIG. 7A
NOTE:To prevent
Drive locking screws:
Vinyl-Clad windows:Wooden windows:
Keep a firm grip on the air conditioner, carefully place the unit into the window opening so the bottom of the air
conditioner frame is against the window sill (FIG. 6A & FIG. 6B). Carefully close the window behind the top rail
of the unit.
OUTSIDEINSIDE
FIG. 6B
Vinyl-Clad WindowsWooden Windows
INSIDE OUTSIDE
FIG. 6A
window
frame

Especificaciones del producto

Marca: Frigidaire
Categoría: aire acondicionado
Modelo: FFRA052ZA1

¿Necesitas ayuda?

Si necesitas ayuda con Frigidaire FFRA052ZA1 haz una pregunta a continuación y otros usuarios te responderán




aire acondicionado Frigidaire Manuales

aire acondicionado Manuales

Últimos aire acondicionado Manuales