Frigidaire IM116000 Manual de Usario

Frigidaire No categorizado IM116000

Lee a continuación 📖 el manual en español para Frigidaire IM116000 (24 páginas) en la categoría No categorizado. Esta guía fue útil para 12 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/24

AUTOMATIC ICE MAKER

INSTALLATION INSTRUCTIONS

P/N: 240394908

The following items will be required to install the ice maker kit:

• ¼ inch copper supply line with shut off valve

• ¼ inch brass compression nut and ferrule

• Freezer shelf (Some models not equipped with shelf). If your model does not have one, contact your dealer to order

one.

The copper tubing and shut off valve are available in a kit from your local hardware or plumbing supply store. Coil enough

tubing at the back of the unit to allow movement for cleaning.

WARNING

• To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from electrical

power before connecting a water supply line to the refrigerator.

• Connect the ice maker to a potable water supply only.

CAUTION

To Avoid Property Damage:

• Copper tubing is recommended for the water supply line. Water supply tubing made of ¼ inch plastic should not be

used since it greatly increases the potential for water leaks. The manufacturer will not be responsible for any damage

if plastic tubing is used for the supply line.

• DO NOT install water supply tubing in areas where temperatures fall below freezing.

• Chemicals from a malfunctioning water softener can damage the ice maker. If the ice maker is connected to softened

water, ensure that the softener is maintained and working properly.

WARNING

Ice maker kit should be installed only by an authorized service technician.

Tools Required:

• Plastic Putty Knife • PhillipsTM Screwdriver

• ¼ inch Socket Wrench or Nut Driver • Needle Nose Pliers

• Adjustable Wrench • Power Drill with PhillipsTM bit

• Small Kitchen Knife

Use This Page to Identify Parts

1. Ice Maker 2. Ice Container 3. Plastic Water Supply Tubing

4. Screws - Qty 2 5. Screws - Qty 2 7. Leveling Bracket - Qty 16. Leveling Bracket Screw -

Qty 1

8. Steel Clamp - Qty 1 10. Water Valves - Qty 19. Plastic Clamp - Qty 2

12. Tube Seal - Qty 111. Water Inlet Tube - Qty 1

6. Remove screws securing Access Cover to cabinet

(interior condensers only - see gure 2C).

7. Use small kitchen knife to cut Ice Maker Installation

label on dashed lines located on outside rear panel of

refrigerator in top, right corner. See Figure 3. Push aps

inward until they stick to unit.

NOTE

On some models, there are two plugs on the left freezer

wall that must be removed. These holes will be used to

mount the Ice Maker (1). (There is also a plug on the back

wall where the water inlet tube (11) will be inserted.)

NOTE

Your refrigerator may have an exterior condenser, as

shown in Figure 2A, or an interior condenser, shown in

gure 2B. If your refrigerator has an exterior condenser,

it may be necessary to loosen the two brackets on the

right side of the condenser. Then the condenser can be

pulled away from the back of the refrigerator far enough

to gain easy entry during the installation process.

Figure 2C shows the location of the screws and the

cutout on the access cover.

1. Unplug refrigerator from electrical outlet.

2. Remove ice tray rack from freezer (some models).

3. Remove spacer. Remove freezer shelf (some models) by

pushing shelf to left until right side of shelf comes free

from holes. Then slowly lift up and pull shelf free from

holes on right side.

4. Use a plastic putty knife to remove plugs from inside

freezer compartment. (See Figure 1.)

5. Remove the harness connector cover, where the ice

maker will plug into, by removing the ¼ inch hex head

screw. (See Figure 1.)

ICE MAKER INSTALLATION INSTRUCTIONS

Harness Connector

Cover

Plastic Plugs

¼" Screw

Figure 1

A B

Exterior

Condenser

Interior

Condenser

Figure 2

Cut on dashed lines

and push in on flaps Figure 3

8. If necessary, remove any foam from within access hole

with needle nose pliers.

Remove and Discard Foam

ICE MAKER

INSTALLATION

ICE MAKER

INSTALLATION

Figure 4

Especificaciones del producto

Marca:	Frigidaire
Categoría:	No categorizado
Modelo:	IM116000
Color del producto:	Wit
Pantalla incorporada:	Ja
Ancho:	520 mm
Profundidad:	465 mm
Altura:	695 mm
Amable:	Zonder reservoir
Soporte de colocación:	Verticaal
Temperatura (máx.):	90 °C
Poder maximo:	44000 W
voltaje-de-entrada-de-CA:	230 V
Ubicación de calefacción:	Binnen
Soporte de baterías de energía solar.:	Nee
Combustible:	Natuurlijk gas
sistema de caldera:	Solo-boilersysteem
Capacidad de agua caliente:	- l/min
Etiqueta de inspección de gas:	SV
Gaskeur HR:	107
Tipo de caldera (etiqueta NL):	HR