Furuno SC-110 Manual de Usario

Furuno No categorizado SC-110

Lee a continuación 📖 el manual en español para Furuno SC-110 (2 páginas) en la categoría No categorizado. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/2
SC50/110 Satellite Compass Operations and information Quick Guide
Specifications: 12-24 VDC (15 W), Heading [95%] (SC50) ±1.0°, (SC110) ±0.6°, follow-up: 45°/s rate-of-turn, settling time: ~4 minutes
Do not extend standard cables
;
LMR-400
(
u
p
to 60m
)
can also be used
;
label CABLE 1
(
BLK
),
CABLE 2
(
YELLOW
),
CABLE 3
(
RED
)
4.5-inch monochrome
LCD, 120 x 64 dots
Turning the Power On/Off
Use power switch on the processor unit to turn the power to the display unit on and off.
Panel Illumination, Display Contrast (64 levels)- press [DIM] key and omni-pad to adjust.
(If screen is blank, press [DIM] key then “▲” omni-pad key multiple times to adjust brilliance higher)
Display Modes - Steering, Nav Data, Set and Drift, Compass Rose, ROT, Heading (True only!)
DATUM settings - Confirm WGS84 (default), use when connected to an AIS and/or IMO compliant systems.
WAAS/DGPS Setup - Press the [MENU] key to open the menu. Make changes and press the [ENT] key.
OTHERS MENU
HOLD HDG DATA
• Allows displaying of last-used heading data at power on. Indicator flashes, noting un-reliable heading .
HDG RESTORATION
• Select GPS signal restore mode, automatically or manually, if lost. Manual restore requires key press.
HDG BACKUP
Select time to display backup data if the GPS signal is lost. This data is also output to external equipment.
Output sentence limitations - IEC 61162-1/2 format (typically compatible with NMEA sentences)
• The number of sentences that can be output depends on baud rate and output interval settings.
• The maximum number of characters per data sentence is shown in the table below.
• Sentences included are HDT, HDM, ROT, ATT, VDR, VTG, GGA, GNS GLL, VHW, VBW, HVE, ZDA
The number of characters that can be output “N” is calculated by the following formula:
N < 0.083 x T x B (Where T = Interval [in seconds] and B = Baud rate (4800 default), 9600, 19200 or 38400
Compliant with: IMO MSC. 116(73), ISO/FDIS 22090-3,IMO A. 694(17), IEC 60945 (2002-08), IEC 61162 (2000)
SC50/110 Operations and Information Quick Guide GP Page 1 3/7/2005
The processor is position sensitive -
Configuration is required; set [INST MENU] settings accordingly. (See manual; section 1.3)
Antenna Mounting - The antenna must be mounted above all other structures for an unobstructed view.
SC50/110
antenna
required horizontal seperation
1.5 meters 3 meters
10cm mast 30cm mast
Horizontal separation between antenna and structure
must be: 10 cm =1.5 m, 30 cm =3 m (minimum)
Distance increases for larger obstructions. See diagram
Failure to comply will cause multi-path reflection problems and heading loss (see “check install section”)
Confirming Satellite Status
Check the receiving condition of each antenna unit as follows:
• Press the [MENU] key to open the menu, select SATELLITE and press the [ENT] key.
• Use ◄ or ► to select between antenna elements to confirm receiving status.
• Press the [DISP] key to close the menu.
SC50/110 Operations and Information Quick Guide GP Page 2 3/7/2005
Position status North DOP RX signal level
(
lower is better
)
Bars that extend past first vertical line
are used in the headin
g
calculation
Elevation 5 °
(More accurate)
Antenna element no.
Troubleshooting: No RX signal on antenna 1, 2, or 3.
Switch antenna cable with one of the other known good
antennas to confirm antenna or processor problem
Elevation 45 °
(Less accurate)
Satellites
highlighted in
black used for
calculation
W
A
AS
Checking Installation- multi-path and receive problems (re-confirm after adding any new near-by structures on the vessel)
Maintenance Menu Access - Press and hold [MENU] and [ENT] keys simultaneously (~ 8 sec.), at third beep release
[MENU] key first, then [ENT] key. Access [ANT MONI] from the maintenance menu and press [ENT].
Multipath Index for the baseline
between antenna 1 and antenna 3
Must be 1.5 or lower
Multipath Index for the baseline
between antenna 1 and antenna 2
Must be 1.5 or lower
Circular Graph displays (in 12 directions) tracking
error in relation to the vessel bow. The highest error
and its opposing direction are shown in black
(illustration shows error at 10 and 4 o’clock
position). Note: Two (2) sectors will always be
illuminated even when no heading loss is present
Bar Graph displays tracking error in 12 directions
Longer bars = more error (caused by obstacles)
Sectors opposite to obstacle may have most error
Elapsed time displays accumulated tracking data
(up to 99 hrs 59 mins). Collect a minimum 12 hrs
of data for valid information.
After confirming above information, turn the vessel in a complete circle to check for correct and stable heading

Especificaciones del producto

Marca: Furuno
Categoría: No categorizado
Modelo: SC-110

¿Necesitas ayuda?

Si necesitas ayuda con Furuno SC-110 haz una pregunta a continuación y otros usuarios te responderán


No categorizado Furuno Manuales

Furuno

Furuno FR-2115-B Manual de Usario

24 Agosto 2024
Furuno

Furuno FS-2570 Manual de Usario

24 Agosto 2024
Furuno

Furuno NAVpilot-5120 Manual de Usario

24 Agosto 2024
Furuno

Furuno BBWX2 Manual de Usario

23 Agosto 2024
Furuno

Furuno TZTBB Manual de Usario

22 Agosto 2024
Furuno

Furuno TZT9 Manual de Usario

21 Agosto 2024
Furuno

Furuno TZT14 Manual de Usario

21 Agosto 2024
Furuno

Furuno SC-110 Manual de Usario

20 Agosto 2024
Furuno

Furuno HRP05 Manual de Usario

20 Agosto 2024
Furuno

Furuno FI-505 Course Pilot Manual de Usario

20 Agosto 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024