GE Café CHP9536SJSS Manual de Usario

GE horno Café CHP9536SJSS

Lee a continuación 📖 el manual en español para GE Café CHP9536SJSS (16 páginas) en la categoría horno. Esta guía fue útil para 11 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/16
Installation
Instructions
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT Save these instructions
for local inspector’s use.
IMPORTANT Observe all governing
codes and ordinances.
Note to Installer Be sure to leave these
instructions with the Consumer.
Note to Consumer Keep these instructions for
future reference.
Product failure due to improper installation is not
covered under the Warranty.
WARNING This appliance must be properly
grounded.
ATTENTION INSTALLER
ALL COOKTOPS MUST BE HARD WIRED
(DIRECT WIRED) INTO AN APPROVED
JUNCTION BOX. A PLUG AND RECEPTACLE” IS
NOT PERMITTED ON THESE PRODUCTS.
Proper installation is the responsibility of the
installer and product failure due to improper
installation is NOT covered under warranty.
PARTS INCLUDED
MATERIALS YOU WILL NEED
TOOLS YOU MAY NEED
30 and 36”
Electric Cooktop - Induction
CUTTING THE COUNTERTOP
If you are installing the cooktop in a solid surface
material such as granite, quartz or any other natural
or synthetic solid surface, we recommend that the
cutout be prepared by a professional cabinet or
countertop installer.
Cooktop cutouts in wood or wood-laminate
countertops may be able to be prepared using a
saber saw and electric drill.
31-2000021 Rev. 2 11-18 GEA
Baffle
(For all installations
except over an oven)
2 Hex-Head Screws
Foam Tape
WB06K5042
2 Hold Down
Brackets
or order alternate
installation kit
WB01X24570
4 Phillips Screws
WB01X1137
Saber Saw
Pencil
Safety Glasses
1/8" Drill Bit & Electric or
Hand Drill
Ruler or Straightedge
Phillips Head
Screwdriver
1/4" Nut Driver
Large Size
Wire Nuts
Junction Box
(Sized for conduit per
local electrical codes.)
90º or Straight
Squeeze Connector
for 1” Conduit
Questions? Call us at 1.800.432.2737 or visit GEAppliances.com.
In Canada, call 1.800.561.3344 or visit GEAppliances.ca.
231-2000021 Rev. 2
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
FOR YOUR SAFETY
For Personal Safety, remove house fuse or open
circuit breaker before beginning installation. Failure
to do so could result in serious injury or death.
Be sure your cooktop is installed properly by a
qualified installer or service technician.
To eliminate the risk of burns or fire due to reaching
over heated surface elements, cabinet storage
located above the surface units should be avoided.
If cabinet storage space is to be provided, the risk
can be reduced by installing a range hood that
projects horizontally a minimum of 5” beyond the
bottom of the cabinets. Cabinet installation above
the cooktop may be no deeper than 13”.
Make sure the cabinets and wall coverings around
the cooktop can withstand the temperatures (up to
200°F) generated by the cooktop.
The cooktop should be easy to reach and lighted
with natural light during the day.
Always disconnect the electrical service to the
cooktop before repairing or servicing the cooktop.
This can be done by disconnecting the fuse or
circuit breaker. Failure to do this could result in a
dangerous or fatal shock. Know where your main
disconnect switch is located. If you do not know,
have your electrician show you.
ELECTRICAL REQUIREMENTS
This appliance must be supplied with the proper
voltage and frequency, and connected to an
individual, properly grounded branch circuit, protected
by a circuit breaker or a time delay fuse as noted on
name plate and on the chart below.
Use the chart below to determine the minimum
recommended dedicated circuit protection:
KW Rating
240V
KW Rating
208V
Recommended
Circuit Size
(Dedicated)
.: .: 20 Amp
4.9 KW–7.2 KW 4.2 KW–6.2 KW 30 Amp
7.3 KW–9.6 KW 6.3 KW–8.3 KW 40 Amp
9.7 KW–12.0 KW 8.4 KW–10.4 KW 50 Amp
We recommend you have the electrical wiring and
hookup of your cooktop connected by a qualified
electrician. After installation, have the electrician show
you where your main cooktop disconnect is located.
Wiring must conform to National Electrical Code and
all local electrical codes. You can get a copy of the
National Electrical Code, ANSI/NFPA No. 70-Latest
Edition, by writing to:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
In Canada, wiring must conform to Canadian Electrical
Code (CEC).
The cooktop conduit wiring is approved for copper
wire connection only, and if you have aluminum house
wiring, you must use special UL approved connectors
for joining copper to aluminum. In Canada, you must
use special CSA approved connectors for joining
copper to aluminum.
You must use a two-wire, three conductor 208/240
VAC, 60 Hertz electrical system. A white (neutral)
wire is not needed for this unit. The cooktop must be
installed in a circuit that does not exceed 125 VAC
nominal to ground.
Refer to the name plate on your cooktop for the KW
rating for your cooktop.
These cooktops
require 40 amp
service for 30” units,
50 amp service for
36” units.
Name plate location
31-2000021 Rev. 2 3
Installation Instructions
PRE-INSTALLATION CHECKLIST
BEFORE YOU BEGIN
WARNING The electrical power to the cooktop
supply line must be shut off while connections are
being made. Failure to do so could result in serious
injury or death.
A When preparing the cooktop opening, make sure
the inside of the cabinet and the cooktop do not
interfere with each other. (See section on
preparing the opening.)
B Remove packaging materials and literature
package from the cooktop before beginning
installation.
C Be sure to place all literature, Owner’s Manual,
Installations Instructions, etc. in a safe place for
future reference.
D Make sure you have all the tools and materials
you need before starting the installation of the
cooktop.
E Your home must provide the adequate electrical
service needed to safely and properly use your
cooktop. (Refer to section on electrical
requirements.)
F When installing your cooktop in your home,
make sure all local codes and ordinances are
followed exactly as stated.
G Make sure the wall coverings, countertop and
cabinets around the cooktop can withstand heat
(up to 200°F) generated by the cooktop.
H Installing cooktop in combination with other
products. Both products must be installed
according to their specific product installation
instructions. Consideration must be given to the
separate electrical requirements and locations:
Over one or two wall ovens:
Only certain models may be installed over
wall ovens. The wall oven and cooktop will
both have a label stating which models are
approved in combination.
Over a Microwave:
See microwave installation instructions for
how to install a microwave under a cooktop.
For vertical dimension of cooktop, see
Approximate Cooktop Dimensions section.
In combination with telescopic downdraft vent:
See telescopic downdraft vent instructions for
how to install a vent behind a cooktop.
The countertop must have a deep flat surface
to accommodate the combined installation of
the cooktop and vent.
Allow 12” clearance between the inlet air ports
on the bottom of the unit.
Over a warming drawer:
See warming drawer instructions for how to
install a warming drawer under a cooktop.
For vertical dimension of cooktop, see
Approximate Cooktop Dimensions section.
I Monogram Flush Mount Kit
If you intend to mount your cooktop flush
to the counter, please order kit number
JXFLUSH1. The flush mount kit provides
supplemental cut-out instructions to mount the
product flush with the counter.

Especificaciones del producto

Marca: GE
Categoría: horno
Modelo: Café CHP9536SJSS

¿Necesitas ayuda?

Si necesitas ayuda con GE Café CHP9536SJSS haz una pregunta a continuación y otros usuarios te responderán




horno GE Manuales

horno Manuales

Últimos horno Manuales