GE JDP39WKWW Manual de Usario

GE horno JDP39WKWW

Lee a continuación 📖 el manual en español para GE JDP39WKWW (16 páginas) en la categoría horno. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/16

31-10595-2 1-07 JR

BEFORE YOU BEGIN

Read these instructions carefully and

completely.

• IMPORTANT — Save these

instructions for local inspector’s use.

• IMPORTANT — Observe all

governing codes and ordinances.

•Note to Installer – Be sure to leave these

instructions with the consumer.

•Note to Consumer – Keep these instructions

for future reference.

•Proper installation is the responsibility of the

installer and product failure due to improper

installation is NOT covered under the warranty.

•NOTE – This appliance must be properly

grounded.

•ATTENTION INSTALLER

All electric drop-in ranges must be hard wired

(direct wired) into an approved junction box.

A plug and receptacle is NOT permitted on

these products

Electric

Drop-In Range

Installation

Instructions JDS28, JDP39

MATERIALS NEEDED

Junction Box Wire NutsStrain Relief Clamp

for 1/2” conduit

PARTS INCLUDED

Lower Trim

2 Screws

2 Shoulder Screws

(for stop device)

TOOLS YOU WILL NEED

1/8” Drill Bit and

Electric or Hand Drill

Phillips Screwdriver

Nut Driver

Level

Tape Measure

Straight Edge

or Square

Hand or Sabre Saw

Standard Screwdriver

Pencil

Safety Glasses

Hammer

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

FOR YOUR SAFETY

WARNING: For personal safety,

remove house fuse or open circuit breaker

before beginning installation. Failure to do

so could result in serious injury or death.

•All rough-in and spacing dimensions must be

met for safe use of your range.

•To reduce the risk of burns or fire when

reaching over hot surface elements, cabinet

storage space above the cooktop should be

avoided. If cabinet storage space is to be

provided above the cooktop, the risk can

be reduced by installing a range hood that

protrudes at least 5” beyond the front of

the cabinets. Cabinets installed above the

cooktop must be no deeper than 13”.

•Be sure your appliance is properly installed

and grounded by a qualified technician.

IMPORTANT SAFETY INSTRUCTIONS

ELECTRICAL REQUIREMENTS

This appliance must be supplied with the

proper voltage and frequency, and connected

to an individual, properly grounded branch

circuit, protected by a circuit breaker or fuse

having amperage as noted on rating plate.

(Rating Plate is located behind the oven

door on the range.)

We recommend you have the electrical wiring

and hookup of your range connected by a

qualified electrician. After installation, have

the electrician show you where your main

range disconnect is located.

Check with your local utilities for electrical

codes which apply in your area. Failure to

wire your range according to governing codes

could result in a hazardous condition. If there

are no local codes, your range must be wired

and fused to meet the requirements of the

National Electrical Code, ANSI/NFPA No. 70—

Latest Edition. You can get a copy by writing:

National Fire Protection Association

Batterymarch Park

Quincy, MA 02269

Effective January 1, 1996, the National

Electrical Code requires that new, but not

existing, construction utilize a four-conductor

connection to an electric range. When

installing an electric range in new construction,

a mobile home, recreational vehicle or an area

where local codes prohibit grounding through

the neutral conductor, follow the instructions

in the section on NEW CONSTRUCTION

AND FOUR-CONDUCTOR BRANCH CIRCUIT

CONNECTION.

You must use a three-wire, single-phase A.C.

208Y/120 Volt or 240/120 Volt, 60 hertz electrical

system. If you connect to aluminum wiring,

properly installed connectors approved for

use with aluminum wiring must be used.

Installation Instructions

Rating

plate location

•Place hands on both sides of

the door, and close the oven

door to the removal position.

This is half way between the

broil stop and fully closed.

•Lift door up

and out until the

hinge arms clear

the slots.

NOTE: The oven door is very heavy. Be sure

you have a firm grip before lifting the oven

door off the hinges. Use caution once the door

is removed. Do not lay the door on its handle.

This could cause dents or scratches.

•Remove packing materials. Remove labels

on door, plastic on trims and panel, and

all tape around the range.

Door removal is not a requirement for

installation of the product, but is an added

convenience. To remove the door:

•Open the oven door as far as it will go.

•Push both hinge

locks down toward

the door frame,

to the unlocked

position. This may

require a flat blade

screwdriver.

PRE-INSTALLATION CHECKLIST

Hinge

unlocked

position

Hinge

slot

Hinge

arm

DO NOT LIFT THE DOOR

BY THE HANDLE!

• Move Range Indoors In Front of Cabinet

Opening

•Protect the kitchen floor! Flatten and place

a piece of the shipping carton in front of the

installation location to protect the flooring.

• Inspect Installation Location

Inspect cutout dimensions and location

of electrical junction box to be sure it fits

within the layout location. See page 4.

Refer to alternate construction section for

the following non-standard installations.

a. Counter opening extends to the wall:

Maintop Filler Kit (JXS66XX), or

Backguard Kit (JXS32XX).

WARNING: If you do not use these kits,

the anti-tip bracket must fit under an

attachment to the wall that can withstand

a force of 200 lbs. in the upward direction.

See Step 1 under INSTALL THE RANGE.

b. Island Installation:

To provide an optimum installation, the

top surface of the countertop must be

level and flat (lie on the same plane)

around the 3 sides that are adjacent to

range cooktop. Proper adjustments to

make the top flat should be made or

gaps between the countertop and range

cooktop may occur. Forcing the cooktop

to fit may cause excessive gaps.

To obtain Kits:

a. Visit GE Web Site (See page 1)

b. Call GE Answer Center (See page 1)

c. Contact Dealer Hinge clears slot

Installation Instructions

Especificaciones del producto

Marca:	GE
Categoría:	horno
Modelo:	JDP39WKWW
Contenido (interior):	400 l
Color del producto:	Zilver
Peso.:	13000 g
Ancho:	820 mm
Profundidad:	1750 mm
Altura:	450 mm
Con cerradura:	Ja
Capacidad máxima de peso:	50 kg
Fácil de usar:	Ja
Tipo-producto:	Harde dakkoffer
Tipo de apertura de la tapa:	2 zijden
Confirmación fácil:	Ja
cerradura central:	Ja