GE Profile P2S975BEMBB Manual de Usario

GE horno Profile P2S975BEMBB

Lee a continuación 📖 el manual en español para GE Profile P2S975BEMBB (52 páginas) en la categoría horno. Esta guía fue útil para 11 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/52

TOOLS YOU WILL NEED

• 1/4” Nut Driver • Level • Pipe Wrench

• Tape Measure • Drill • Safety Glasses

• Phillips Head • Flat Head • Wrench or Pliers

Screwdriver Screwdriver (for 1 7/16” Nut)

MATERIALS YOU MAY NEED

31-10641-3 03-09 JR

Printed in the United States

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com

In Canada, call 1.800.561.3344 or Visit our Website at: www.GEAppliances.ca

Installation

Self-Cleaning Dual Fuel

Instructions

Slide-In Range

P2S975

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

•IMPORTANT —Save these

instructions for local inspector’s use.

•IMPORTANT —Observe all

governing codes and ordinances.

•Note to Installer – Be sure to leave these

instructions with the Consumer.

•Note to Consumer – Keep these

instructions for future reference.

•Product failure due to improper installation

is not covered under the Warranty.

WARNING —This appliance must

be properly grounded.

•Proper installation is the responsibility

of the installer and product failure due

to improper installation is NOT covered

under warranty.

WARNING —

Before beginning

the installation, switch power off at service

panel and lock the service disconnecting means

to prevent power from being switched on

accidentally. When the service disconnecting

means cannot be locked, securely fasten

a prominent warning device, such as a tag,

to the service panel.

IN THE COMMONWEALTH OF

MASSACHUSETTS:

• This product must be installed by

a licensed plumber or gas fitter.

• When using ball-type gas shut-off valves,

they shall be the T-handle type.

• A flexible gas connector, when used,

must not exceed 3 feet.

PARTS INCLUDED

Anchor SleevesLag Bolts

(For Concrete Floors Only)

Shut Off ValvePipe Fittings

CSA-Approved Flexible Gas Line

3/8″Min. ID, 1/2″NPT Connection,

3-foot Maximum Length (Massachusetts only)

Joint Sealant

Screws

Rear Filler

2 Screws

FOR YOUR SAFETY

If you did not receive an anti-tip bracket with your

purchase, call 1.800.626.8774 to receive one at no cost.

(In Canada, call 1.800.561.3344.)

For installation instructions of the bracket, visit:

GEAppliances.com. (In Canada, www.GEAppliances.ca.)

Anti-Tip Bracket

Kit Included

Installation Instructions

FOR YOUR SAFETY:

WARNING — If the information

in this manual is not followed exactly, a fire,

explosion or gas leak may result causing

property damage, personal injury or death.

Do not store or use gasoline or other

flammable vapors and liquids in the vicinity

of this or any other appliance!

WHAT TO DO IF YOU

SMELL GAS:

• Do not try to light any appliance. Do not

touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier,

call the fire department.

Installation and service must be performed

by a qualified installer, service agency or

the gas supplier.

IMPORTANT SAFETY INSTRUCTIONS

This range has been design certified by

UNDERWRITERS LABORATORIES for use in

the United States and Canada. You’ll find

safety precautions in your Owner’s Manual.

Read them carefully.

• Installation of this range must conform with

local codes or in the absence of local codes

with the National Fuel Gas Code, ANSI

Z223.1–Latest edition.

• Be sure your range is installed properly by

a qualified installer or service technician.

• To eliminate reaching over surface burners,

cabinet storage above burner should be

avoided.

• Do not install the unit near an outside door

or where a draft may affect its use.

FOR YOUR SAFETY:

WARNING — For personal safety,

remove house fuse or open circuit breaker

before beginning installation. Failure to do so

could result in serious injury or even death.

All rough-in and spacing dimensions must be

met for safe use of your range. Electricity to

the range can be disconnected at the outlet

without moving the range if the outlet is in

the preferred location (remove lower drawer).

To reduce the risk of burns or fire when

reaching over hot surface elements, cabinet

storage space above the cooktop should be

avoided. If cabinet storage space is to be

provided above the cooktop, the risk can

be reduced by installing a range hood that

protrudes at least 5” beyond the front of the

cabinets. Cabinets installed above a cooktop

must be no deeper than 13”.

Be sure your appliance is properly installed

and grounded by a qualified technician.

Rating

plate location

ELECTRICAL REQUIREMENTS

This appliance must be supplied with the

proper voltage and frequency and connected

to an individual, properly grounded branch

circuit, protected by a circuit breaker or fuse

having a recommended amperage rating per

the table below.

BREAKER OR FUSE SIZE

240V 40 Amps

208V 40 Amps

NOTE: Check Local Codes for required

breaker size.

Rating plate is located above the storage drawer

below the oven frame.

We recommend you have the electrical wiring

and hookup of your range connected by a

qualified electrician. After installation, have the

electrician show you where your main range

disconnect is located.

Installation Instructions

ELECTRICAL REQUIREMENTS-

(cont.)

Check with your local utilities for electrical

codes which apply in your area. Failure to

wire your range according to governing

codes could result in a hazardous condition.

If there are no codes, your range must be

wired and fused to meet the requirements of

the National Electrical Code, ANSI/NFPA No.

70–Latest edition. You can get a copy by

writing:

National Fire Protection Association

Batterymarch Park

Quincy, MA 02269

Effective January 1, 1996, the National

Electrical Code requires that new, but not

existing, construction utilize a four-conductor

connection to an electric range. When installing

an electric range in new construction, a mobile

home, recreational vehicle or an area where

local codes prohibit grounding through the

neutral conductor, follow the instructions in the

section on NEW CONSTRUCTION AND FOUR-

CONDUCTOR BRANCH CIRCUIT

CONNECTION.

In Canada your range must be wired and

fused to meet the requirements of the

Canadian Electrical Code.

You must use a three-wire, single-phase

A.C. 208Y/120 Volt or 240/120 Volt, 60 hertz

electrical system.

INSPECT INSTALLATION

LOCATION

Refer to alternate construction section for

the following non-standard installations.

Counter opening extends to the wall:

Maintop Filler (supplied with the range.)

(See page 15 for Installation Instructions) or

Backguard (Kit JXS32XX or JXS37XX).

Counter height greater than 36-3/4″:

Lower Trim Slide-In (Kit JXS56XX).

One side is not enclosed by a cabinet:

Bodyside (Kit JXS77XX).

Island Installation:

To provide an optimum installation, the top

surface of the countertop must be level

and flat (lie on the same plane) around

the 3 sides that are adjacent to range

cooktop. Proper adjustments to make

the top flat should be made or gaps

between the countertop and range cooktop

may occur. Forcing the cooktop to fit may

cause excessive gaps.

To obtain Kits:

a. Visit GE Web Site (See page 1)

b. Call GE Answer Center (See page 1)

c. Contact Dealer

MOVE RANGE INDOORS IN

FRONT OF CABINET OPENING

Do not use hand trucks when moving the

unpackaged range.

PROTECT THE KITCHEN

FLOOR

Flatten and

place a piece

of the shipping

carton in

front of

the installation

location to

protect

the flooring.

ADJUST

PRE-INSTALLATION

CHECKLIST

Especificaciones del producto

Marca:	GE
Categoría:	horno
Modelo:	Profile P2S975BEMBB
Peso.:	244 g
Fuente de alimentación:	DC 7 - 20V
Resolución:	1.3MP
Modelo de procesador:	ARTPEC-A
Resolución Máxima:	1280 x 1024 Pixels
Tipo de fuente de energía:	Power over Ethernet (PoE)
Iluminación mínima:	1 Lux
Detección de movimiento por vídeo:	Ja
Micrófono, entrada de línea:	Ja
Rango focal:	3 - 8 mm
Tamaño del sensor óptico:	1/3 "
Tipo de sensor de imagen:	CMOS
Velocidad de obturación de la cámara:	1/15000 - 1/4 s
Micrófono incorporado:	Ja
Memoria interna:	64 MB
Conexiones:	1x RJ-45
Máximo 30 cuadros por segundo:	8/20, 12/30 fps
Protocolos de red compatibles:	IPv4/v6, HTTP, HTTPS, QoS Layer 3 DiffServ, FTP, SMTP, Bonjour, UPnP, SNMPv1/v2c/v3 (MIB-II), DNS, DynDNS, NTP, RTSP, RTP, TCP, UDP, IGMP, RTCP, ICMP, DHCP, ARP, SOCKS
Exploración progresiva:	Ja
Memoria flash:	8 MB
Alimentación a través de Ethernet (PoE):	Ja
Dimensiones (Ancho x Fondo x Alto):	44 x 88 x 172 mm
Consumo de energía (típico):	5 W
Temperatura de funcionamiento (TT):	0 - 45 °C
Humedad relativa de funcionamiento (VV):	20 - 80 procent
Ángulo de visión de la lente, horizontal:	37 °
Detección de audio:	Ja