GE Profile PS900DPCC Manual de Usario

GE horno Profile PS900DPCC

Lee a continuación 📖 el manual en español para GE Profile PS900DPCC (4 páginas) en la categoría horno. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

• IMPORTANT — Save these

instructions for local inspector’s use.

• IMPORTANT — Observe all gov-

erning codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with Consumer.

• Note to Consumer – Keep these instruc-

tions for future reference.

• Skill level – Installation of this appliance

requires basic mechanical skills

and advanced electrical skills.

•Proper installation is the responsibility

of the installer.

•Product failure due to improper installation

is not covered under Warranty.

Installation Instructions

30"Electric Slide-In Ranges

FOR YOUR SAFETY:

If you did not receive an anti-tip bracket with your purchase,

call 1.800.626.8774 to receive one at no cost. (In Canada,

call 1.800.561.3344.) For installation instructions of the bracket,

visit: www.geappliances.com. (In Canada, www.geappliances.ca.)

Anti-Tip Bracket

Kit Included

Questions? Call 1.800.GE.CARES (1.800.432.2737) or visit www.geappliances.com

In Canada, call 1.800.561.3344 or visit www.geappliances.ca

WARNING

—

Before

beginning the installation, switch

power off at service panel and

lock the service disconnecting

means to prevent power from

being switched on accidentally.

When the service disconnecting

means cannot be locked, secure-

ly fasten a prominent warning

device, such as a tag,

to the service panel.

MATERIALS YOU MAY NEED TOOLS YOU WILL NEED

(UL Listed 40 AMP)

4-Wire Cord 4' long OR

3-Wire Cord 4' long

Squeeze Connector

(For Conduit

Installations Only)

REMOVE PACKAGING MATERIALS: Failure to remove packaging

materials could result in damage to the appliance. Remove all packing parts from oven,

racks, heating elements and drawer. Also, remove protective film and labels on the door,

cooktop (do not remove side protection on glass cooktops) and backguard.

Do not remove protective channel from sides of glass cooktop, if applicable, until later

in installation.

Drill with 1/8" Bit

Safety Glasses

Adjustable Wrench

Level

Tin Snips

Tape Measure

Pliers

1/4" Nut Driver

PREPARE THE OPENING (FOR INDOOR USE ONLY)

If the countertop area is not flat, excess tension may be applied to the glass cooktop causing breakage

and voiding the warranty. Make sure the wall covering, countertop, flooring and cabinets around the range

can withstand the heat (up to 200˚F) generated by the range.

A. Allow 30

minimum clearance between surface units and bottom of unprotected wood or metal cabinet,

or allow a 24

minimum when bottom of wood or metal cabinet is protected by no less then 1/4

thick

flame retardant millboard covered with no less than No. 28 MSG sheet metal (.015

thick), .015

thick

stainless steel, .025

aluminum or .020

copper.

B. This appliance has been approved for 0

spacing to adjacent surfaces above the cooktop. However,

a minimum 6

spacing to surfaces less than 15

above the cooktop and adjacent cabinetry

is recommended to reduce exposure to steam, grease splatter and heat. Allow 1/4

minimum clearance

at the back wall.

To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space above

the cooktop should be avoided. If cabinet storage space is to be provided above the cooktop, the risk can

be reduced by installing a range hood that projects at least 5

beyond the front of the cabinets. Cabinets

installed above the cooktop must be no deeper than 13

31-1/4"

2-7/8"

To front

surface of

countertop

25-3/4"

(excluding

handle)

Height from floor to range top

35-7/8"–36-1/2"

36-1/2"–38" with lower trim

slide-in kit (see Step 3)

Acceptable electrical outlet area.

Orient electrical receptacle so

the length is parallel to floor.

46-3/8"

36-1/4"

7-1/2"

20-5/8"

Door clearance from

front surface of

countertop

24"

30"

Min.

9/16"

15" Min.

7-1/2"

2-1/2"

23-3/16"

Acceptable electrical

outlet area

25"

29-15/16"–30-1/16"

For Profile models only, if

countertop has a raised edge,

shave raised edge to clear

31-1/8" wide control panel.

1/4" Min. Flat

35-7/8"–38" from

Floor to countertop

2-1/2"

1-1/4" Min, from countertop

to top of cabinet drawer.

NOTE: Use a 4' power cord to prevent

interference with the storage drawer.

Power cords 4-1/2' to 6' long may have

to be dressed to allow for proper draw-

er closing.

DOOR REMOVAL (optional)

Door removal is not a requirement for installation of the product

but is an added convenience. To remove the door:

A. Open the oven door as far as it will go.

B. Push both hinge locks down toward the door frame to the unlocked posi-

tion. This may require a flat-blade screwdriver.

DO NOT LIFT THE DOOR BY THE HANDLE!

C. Place hands on both sides of the door, and close the oven door

to the removal position. (Approximately 1"-2" from the closed position.)

D. Lift door up and out until the hinge arms clear the slots.

NOTE: The oven door is very heavy. Be sure you have a firm grip before lift-

ing the oven door off the hinges. Use caution once the door is removed.

Do not lay the door on its handle. This could cause dents or scratches.

Hinge

unlocked

position

Hinge

slot

Hinge

arm

Rating

plate

Rating

plate

PREPARE THE RANGE

Protective

channel

STORAGE DRAWER REMOVAL

A. Pull drawer out until it stops.

B. Lift front of drawer until the stops clear the guide.

C. Pull forward and remove the drawer.

Rail

Guide

Stop

POWER CORD AND CONDUIT INSTALLA-

TION

A. Remove wire cover (on the back of range)

by removing screws using a 1/4" nut driver.

Do not discard these screws.

For power cord and 1" conduit only,

remove the

knockout ring (13⁄8") located on bracket directly

below the terminal block. To remove the knockout,

use a pair of pliers to bend the knockout ring away

from the bracket and twist until ring is removed.

ELECTRICAL REQUIREMENTS

WARNING: This appliance must be properly grounded.

WARNING:

All new constructions, mobile homes, recreational vehicles and installations

where local codes do not allow grounding through neutral require a 4-conductor, UL-listed range cord.

WARNING: To prevent fire or shock, do not use an extension cord with this appliance.

WARNING: To prevent shock, remove house fuse or open circuit breaker before begin-

ning installation.

We recommend you have the electrical wiring and hookup of your range connected by a qualified

electrician. After installation, have the electrician show you how to disconnect power from the range.

You must use a single-phase, 120/208 VAC or 120/240 VAC, 60 hertz electrical system. If you

connect to aluminum wiring, properly installed connectors approved for use with aluminum wiring

must be used.

Effective January 1, 1996, the National Electrical Code requires that new construction (not existing)

utilize a 4-conductor connection to an electric range. When installing an electric range in new con-

struction, mobile home, recreational vehicle, or an area where local codes prohibit grounding

through the neutral conductor, refer to the section on four-conductor branch circuit connections.

Check with your local utilities for electrical codes which apply in your area. Failure to wire your

oven according to governing codes could result in a hazardous condition. If there are no local

codes, your oven must be wired and fused to meet the National Electrical Code, NFPA No. 70 –

latest edition, available from the National Fire Protection Association.

This appliance must be supplied with proper voltage and frequency and connected to an individ-

ual, properly grounded, 40 amp (minimum) branch circuit protected by a circuit breaker

or time-delay fuse.

Use only a 3-conductor or a 4-conductor UL-listed range cord.

These cords may be provided with ring terminals on wire and

a strain relief device.

A range cord rated at 40 amps with 125/250 minimum volt range

is required. A 50 amp range cord is not recommended, but if used,

it should be marked for use with nominal 1

3⁄8" diameter connection

openings. Care should be taken to center the cable and strain relief

within the knockout hole to keep the edge from damaging the cable.

The rating plate is located on the oven frame or on the side

of the drawer frame.

Knockout

ring in

bracket

Knockout ring

removed

Terminal block

(appearance

may vary)

ALTERNATE INSTALLATION / CONSTRUCTION KITS

Description:

Backguard Kit: Adds a decorative backguard to the rear

of the range. This kit can only be used when the opening

in the countertop is 25" deep.

Maintop Filler Kit: Adds a filler strip to the rear of the range.

This kit can only be used when the opening in the countertop

is 25" deep. This kit cannot be used with a backguard kit.

Body Side Kit: Contains a color-matched side panel which

can be used to create a finished appearance on either side

of the range.

Lower Trim Kit: Contains a color-matched toe kick

and extra-long leveling legs. Designed to be used when

the range needs to be raised higher than 36-1/2".

Use:

Designed to be used when replacing

a free-standing range with a slide-in.

Used to fill gap between the range

back and wall.

Designed to be used when cabinets

are absent on one side of the range.

Use kit when countertop height is

36-1/2" to 38" high.

To order accessory kits, call 1.866.775.4557, or visit www.GEAppliances.com.

Hinge clears slot

Wire

cover

3-WIRE INSTALLATION

WARNING: The neutral or ground wire of the power cord must be connected

to the neutral terminal located in the center of the terminal block. Ground strap must connect

the neutral teminal to the ground plate. The power leads must be connected to the lower

left and the lower right terminals of the terminal block.

DO NOT remove the ground strap connection.

FOR POWER CORD INSTALLATION

A. Remove the 3 lower terminal screws from the terminal block.

B. Insert the 3 screws through each power cord terminal termi-

nal ring and into the lower terminals of the terminal block. Be

certain that the center wire (white/neutral)

is connected to the center lower position of the terminal

block.

C. Tighten screws securely into the terminal block.

FOR CONDUIT INSTALLATION

A. Loosen the 3 lower terminal screws from the terminal block.

B. Strip wire to expose tip about 5/8" long. Insert the center

(white/neutral) wire tip through the bottom center terminal block opening. On

certain models, the wire will need to be inserted

through the ground strap opening and then into the bottom

center block opening. Insert the two side bare wire tips into

the lower left and the lower right terminal block openings.

C. Tighten screws until the wire is firmly secured (35 to 50 inch-lbs.).

Do not over-tighten the screws.

NOTE: ALUMINUM WIRING: Aluminum building wire may

be used but it must be rated for the correct amperage and voltage.

PROCEED TO STEP 9.

Ground

strap

Terminal block

(appearance

may vary)

Neutral

terminal

Power cord

Ground

plate

Power Cord

4-WIRE INSTALLATION

WARNING: The neutral wire of the supply

circuit must be connected to the neutral terminal

located in the lower center of the terminal block.

The power leads must be connected to the lower

left and the lower right terminals of the terminal block.

The grounding lead must be connected to the frame

of the range with the ground plate and the green

ground screw.

FOR POWER CORD INSTALLATION

A. Remove the 3 lower terminal screws from

the terminal block. Remove the ground screw

and ground plate and retain them. Cut and discard

the ground strap. DO NOT DISCARD ANY SCREWS.

B. Insert the one ground screw into the power cord ground

wire terminal ring, through the ground plate and into

the frame of the range.

C. Insert the 3 terminal screws (removed earlier) through

each power cord terminal ring and into the lower terminals

of the terminal block. Be certain that the center wire

(white/neutral) is connected to the center lower position

of the terminal block. Tighten screws securely into

the terminal block.

FOR CONDUIT INSTALLATION

A. Loosen the 3 lower terminal screws from the terminal block.

Remove the ground screw and ground plate and retain

them. Cut and discard the ground strap. DO NOT

DISCARD ANY SCREWS.

B. Strip the wire to expose tip about 5/8" long. Insert

the ground bare wire tip between the range frame

and the ground plate (removed earlier) and secure

it in place with the ground screw (removed earlier).

Insert the bare wire (white/neutral) tip through the bottom

center of the terminal block opening. Insert the two

side bare wire tips into the lower left and the lower

right terminal block openings.

C. Tighten the screws until the wire is firmly secured

(35 to 50 inch-lbs.). Do not over-tighten the screws.

NOTE: ALUMINUM WIRING: Aluminum building wire may be used but it must be rated

for the correct amperage and voltage.

8Before–Power Cord and Conduit

Terminal

block

Terminal

block

Neutral termi-

nal

Neutral

terminal

Ground

strap

Ground plate

(grounding to

range)

Ground

screw

Ground strap

After–Conduit

Terminal

block

Ground

plate

(grounding

to range)

Wire

tips

Ground screw

After–Power Cord

REPLACE THE WIRE COVER

Replace wire cover on range back by sliding its left edge under

the retaining tabs and replace the screws removed earlier. Make sure

that no wires are pinched between cover and range back.

POWER CORD AND CONDUIT INSTALLATION (CONT.)

C. For power cord installations only (see the next

step if using conduit), assemble the strain relief

in the hole. Insert the power cord through the strain

relief and tighten. Allow enough slack to easily

attach the cord terminals to the terminal block.

If tabs are present at the end of the winged

strain relief, they can be removed for a better fit.

NOTE: Do not install the power cord without a

strain relief. The strain relief bracket MUST be

installed before reinstalling the rear range wiring

cover.

D. For conduit installations only, purchase a squeeze

connector matching the diameter of your conduit and

assemble it in the hole. Insert the conduit through the

squeeze connector and tighten. Allow enough slack to eas-

ily attach the wires to the terminal block.

NOTE: Do not install the conduit without a squeeze con-

nector. The squeeze connector MUST be installed

before reinstalling the rear range wiring cover.

Power cord

Strain relief

Terminal

block

Bracket

Squeeze connector

Terminal

block

Bracket

Wire

cover

Wire tips

Terminal

block

Conduit

Especificaciones del producto

Marca:	GE
Categoría:	horno
Modelo:	Profile PS900DPCC
Colocación del dispositivo:	Ingebouwd
Tipo de operación:	Touch
Color del producto:	Zwart
Número de niveles de potencia:	17
Pantalla incorporada:	Ja
Peso.:	15517 g
Ancho:	791 mm
Profundidad:	522 mm
Altura:	51 mm
Longitud del cable:	1.1 m
Bloqueo infantil:	Ja
Peso del embalaje:	16900 g
Ancho del embalaje:	953 mm
Empaquetadura en profundidad:	608 mm
Altura del embalaje:	126 mm
Tipo de material (arriba):	Glaskeramiek
Potencia quemador/zona de cocción 2:	2600 W
Potencia quemador/zona de cocción 3:	1400 W
Potencia quemador/zona de cocción 1:	3300 W
Número de quemadores/zonas de cocción:	3 zone(s)
tipo de placa:	Inductiekookplaat zones
Quemador/zona de cocción tipo 1:	Extra groot
Quemador/zona de cocción tipo 2:	Extra groot
Tipo de quemador/zona de cocción 3:	Sudderen
Número de quemadores de gas:	0 zone(s)
Número de zonas de cocción electrónicas:	3 zone(s)
Posición de control:	Boven voorzijde
Carga conectada (eléctrica):	7400 W
Ancho del compartimento de instalación:	750 mm
Profundidad del compartimento de instalación:	490 mm
Altura del compartimento de instalación:	51 mm
Carga conectada (gas):	0 W
Ancho de la placa:	80 cm
Profundidad del compartimento de instalación (min):	490 mm
Indicador de calor residual:	Ja
Número de zonas de cocción que se utilizarán simultáneamente:	3
Tipo de marco:	U-vormige sierlijst
Cerradura de limpieza:	Ja
Certificación:	AENOR, CE
Forma del marco:	Schuin
Fuente de alimentación quemador/zona de cocción 1:	Electrisch
Fuente de alimentación quemador/zona de cocción 2:	Electrisch
Fuente de alimentación quemador/zona de cocción 3:	Electrisch
Profundidad del compartimento de instalación (máx.):	500 mm
Posición del quemador/zona de cocción 1:	Links
Diámetro quemador/zona de cocción 1:	240 x 400 mm
Posición quemador/zona de cocción 2:	Centraal
Quemador/zona de cocción diámetro 2:	280 mm
Posición quemador/zona de cocción 3:	Rechts voor
Quemador/zona de cocción diámetro 3:	150 mm
Forma zona de cocción 1:	Rechthoekig
Forma zona de cocción 2:	Rond
Forma zona de cocción 3:	Rond
voltaje-de-entrada-de-CA:	220 - 240 V
Frecuencia-de-entrada-de-CA:	50 - 60 Hz