GE ZDIS150ZSS Manual de Usario

GE Máquina de hielo ZDIS150ZSS

Lee a continuación 📖 el manual en español para GE ZDIS150ZSS (18 páginas) en la categoría Máquina de hielo. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/18
Installation
Instructions
Automatic Ice maker
ZDIC150
ZDIS150
Design Guide
With Installation Instructions
monogram.com
Installation Instructions
 BEFORE YOU BEGIN:
Read these instructions completely and carefully.
 IMPORTANT:
Save these instructions for local inspector’s use.
 IMPORTANT:
Observe all governing codes and ordinances.
Note to Installer – Be sure to leave these
instructions with the Consumer.
Note to Consumer – Keep these instructions with
your Owner’s Manual for future reference.
WARNING:
This appliance must be properly grounded.
Failure to do so can result in death, fire or electrical
shock. See “Power Supply,” page 6.
AVERTISSEMENT :
Cet appareil doit être correctement mis à la terre.
Le non-respect de ces instructions peut causer la
mort, un incendie ou un choc électrique. Consulter «
Alimentation électrique », page 6.
If you received a damaged ice maker, you should
immediately contact your dealer or builder.
Proper installation is the responsibility of the
installer. Product failure due to improper installation
is not covered under the GE Appliance Warranty.
See the Owner’s Manual for warranty information.
8VHWKLVDSSOLDQFHRQO\IRULWVLQWHQGHGSXUSRVH
Check with local utilities for electrical codes that
apply in your area. Local codes vary. Installation,
electrical connections and grounding must comply
with applicable codes. In the absence of local codes,
the ice maker should be installed in accordance
with National Electrical Code ANSI/NFPA 70-1990 or
latest edition.
For Monogram local service in your area, call
1.800.444.1845.
For Monogram Service in Canada, call
1.800.561.3344.
For Monogram Parts and Accessories, call
1.800.626.2002.
2
CONTENTS
Design Information
Models Available .................................................................... 3
Optional Accessories ........................................................... 3
Tools and Materials Required ........................................ 3
Cutout & Product Dimensions .........................................4
Installation
Advance Planning .................................................................4
Water Supply ........................................................................... 5
Power Supply ...........................................................................6
Remove Packaging ............................................................... 6
Water Filtration System .................................................6, 7
Adjust Height of Ice maker ...............................................7
Connect the Drain .................................................................9
Connect Water Supply to Appliance ............................9
Reverse Door Swing ...................................................10, 11
Accessories
ZPK2 Auxiliary Pump Kit ............................................12-15
ZIP75BB Kit for 3/4” thick panels ..........................16, 17
Design Information
MODELS AVAILABLE
ZDIC150ZBB, ZDIS150ZSS
Available in black and stainless steel.
The ice maker may be installed below a countertop
or used free-standing.
3
OPTIONAL ACCESSORIES
=,3%%³For the installation of a trimless
3/4” thick custom panel on black models (not for
stainless steel models). This kit provides a handle
that can be installed with the custom panel.
A custom handle of your choice may be installed onto
the 3/4” panel. See installation instructions
on pages 10 and 11.
ZPK2 Drain Pump Kit - For use when a floor drain is
not available. The drain pump must be installed
inside the unit and can pump discharge water at a
maximum vertical height of 10 feet. 10 feet of tubing
is supplied with the kit.
TOOLS AND MATERIALS REQUIRED FOR BASIC INSTALLATION
µVRFNHW
µDGMXVWDEOHZUHQFK
/HYHO
*(6PDUW&RQQHFW™ Refrigerator Tubing Kit or 1/4” O.D.
copper tubing, of sufficient length to reach the installation
)ODWEODGHVFUHZGULYHU
µDQGµRSHQHQGZUHQFKHVRUDGMXVWDEOHZUHQFKHV
µQXWGULYHU

Especificaciones del producto

Marca: GE
Categoría: Máquina de hielo
Modelo: ZDIS150ZSS

¿Necesitas ayuda?

Si necesitas ayuda con GE ZDIS150ZSS haz una pregunta a continuación y otros usuarios te responderán


Máquina de hielo GE Manuales

GE

GE Profile Opal P4AAKASSWOW Manual de Usario

17 Septiembre 2024
GE

GE Profile Opal P4AAKASSWBB Manual de Usario

17 Septiembre 2024
GE

GE Profile Opal P4AAKASSWSS Manual de Usario

17 Septiembre 2024
GE

GE Profile Opal XPIO23SWSS Manual de Usario

17 Septiembre 2024
GE

GE UNC15NPRII Manual de Usario

10 Agosto 2024
GE

GE Profile OPAL01PKT Manual de Usario

6 Agosto 2024
GE

GE Profile Opal XPIOX3BCBT Manual de Usario

2 Agosto 2024
GE

GE Profile Opal P4INDOS6RBB Manual de Usario

30 Julio 2024
GE

GE ZDIS150ZSS Manual de Usario

26 Julio 2024

Máquina de hielo Manuales

Últimos Máquina de hielo Manuales

Beper

Beper 70257 Manual de Usario

27 Octubre 2024
Hoshizaki

Hoshizaki F-801MAJ Manual de Usario

26 Octubre 2024
U-Line

U-Line U-3018CLRINT-00B Manual de Usario

26 Octubre 2024
Yamazen

Yamazen YSIA-F25 Manual de Usario

23 Octubre 2024
Summit

Summit BIM182 Manual de Usario

21 Octubre 2024
Edgestar

Edgestar IB250SSOD Manual de Usario

20 Octubre 2024
Edgestar

Edgestar IB121SS Manual de Usario

20 Octubre 2024
Edgestar

Edgestar IB250BL Manual de Usario

20 Octubre 2024
Unold

Unold 48892 Manual de Usario

19 Octubre 2024
Koenic

Koenic KIM 91221 B Manual de Usario

16 Octubre 2024