GE ZV681YSS Manual de Usario

Lee a continuación 📖 el manual en español para GE ZV681YSS (16 páginas) en la categoría campana extractora. Esta guía fue útil para 14 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/16
Monogram.
We bring good things to life.
®
If you have questions, call 800-GE-CARES or visit our website at: www.monogram.com
Installation
Instructions
30", 36" and 48"
Proessional Vent Hoods
48" Wide Models:
ZV881, ZV891, ZV880, ZV890
36" Wide Models:
ZV671, ZV681, ZV670, ZV680
30" Wide Models:
ZV370, ZV371
Installation Preparation
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRICAL
SHOCK OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
A. Use this unit only in the manner intended by the
manufacturer. If you have any questions, contact the
manufacturer.
B. Before servicing or cleaning unit, switch power off
at the service panel and lock service panel to prevent
power from being switched on accidentally. If the
service panel cannot be locked, fasten a tag or
prominent warning label to the panel.
For general ventilating use only. Do not use to
exhaust hazardous or explosive materials or vapors.
Structural framing, installation work and electrical
wiring must be done by qualified person(s).
In accordance with all applicable codes and standards
including fire-rated construction.
Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of
fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer’s
guideline and safety standards such as those pub-
lished by the National Fire Protection Association
(NFPA), and the American Society for Heating,
Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local code authorities.
Local codes vary. Installation electrical connections
and grounding must comply with applicable codes.
In the absence of local codes, the vent should be
installed in accordance with National Electrical Code
ANSI/NFPA 70-1990 or latest edition.
TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.
2
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT - Save these instructions for
local inspector’s use.
IMPORTANT - Observe all governing
codes and ordinances.
Note to Installer - Be sure to leave these instruc-
tions with the Consumer.
Note to Consumer - Keep these instructions with
your Owner’s Manual for future reference.
– Installation of this appliance requiresSkill Level
basic mechanical and electrical skills.
Completion time – 1 to 3 hours.
• Proper installation is the responsibility of the
installer.
• Product failure due to improper installation is not
covered under the Warranty.
For Monogram local service in your area,
1-800-444-1845.
For Monogram service in Canada, call
1-888-880-3030.
For Monogram Parts and Accessories, call
1-800-626-2002.
CAUTION:
Due to the weight and size of these vent hoods and to
reduce the risk of personal injury or damage to the
product, TWO PEOPLE ARE REQUIRED FOR
PROPER INSTALLATION.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
WARNING:
To reduce the risk of fire or electrical shock, do not
use this range hood with any external solid-state speed
control device. Any such alteration from original
factory wiring could result in damage to the unit and/
or create an electrical safety hazard.
CONTENTS
Installation Preparation
Models, Duct Covers, Ductwork Accessories................... 3
Product Dimensions, Product Clearances ...................... 4
Advance Planning ............................................................. 5
Power Supply ................................................................... 5
Duct Fittings ...................................................................... 6
Installation Instructions
Tools and Materials Required .......................................... 7
Step 1, Remove Packaging ............................................... 7
Step 2, Check Installation Hardware............................... 7
Step 3, Determine Accessories, Ductwork and Wiring
Locations .............................................................. 8
Step 4, Recommended Wall Mounting Method
Wall Framing For Hood Support ........................ 9
Step 5, Install Hood Onto Wall...................................... 10
Step 6, Alternate Soffit Mounting Method
Soffit Framing .................................................. 11
Step 7, Connect Electrical .............................................. 12
Step 8, Connect Ductwork ............................................. 12
Step 9, Reassemble Hood............................................... 12
Step 10, Install Duct Cover ............................................ 13
Step 11, Install Filters ..................................................... 13
Installation Preparation
3
MODELS AVAILABLE
These vent hoods are designed to be installed onto a
wall. They can be installed beneath a soffit and with duct
cover accessories that conceal ductwork.
Choose 48" and 36" wide models with straight sides, or
models with sides that taper inwards from the bottom to
the top. 30" models have straight sides.
DUCT COVER ACCESSORIES
Before you begin:
Decorative duct covers are available in 6" or 12" heights.
The duct covers conceal the ductwork running from the
top of the hood to the ceiling or soffit. Before you begin,
you should determine the installation height of the hood
and order the correct size duct cover.
48" Wide Models:
ZV881, ZV880 – with tapered sides
ZV891, ZV890 – with straight sides
36" Wide Models:
ZV671, ZV670 – with tapered sides
ZV681, ZV680 – with straight sides
30" Wide Models:
ZV371, ZV370 – with straight sides
Oval Shape Duct Covers for Models for Tapered Sided Models
Hood Model 6” Duct Cover Dimensions
ZV881 , ZV880 ZX6DC48 6”Hx27-3/8”Wx10-1/4”D
ZV671, ZV670 ZX6DC36 6”Hx22-1/2”Wx9-3/16”D
Hood Model 12” Duct Cover Dimensions
ZV881, ZV880 ZX12DC48 12”Hx27-3/8”Wx10-1/4”D
ZV671, ZV670 ZX12DC36 12”Hx22-1/2”Wx9-3/16”D
Square Shape Duct Covers for Straight Sided Models
Hood Model 6” Duct Cover Dimensions
ZV891, ZV890 ZX6DC49 6”Hx47-7/8”Wx12”D
ZV681, ZV680 ZX6DC38 6”Hx35-7/8”Wx12”D
ZV371, ZV370 ZX6DC30 6”Hx29-7/8”Wx12”D
Hood Model 12” Duct Cover Dimensions
ZV881, ZV880 ZX12DC49 12”Hx47-7/8”Wx12”D
ZV681, ZV680 ZX12DC38 12”Hx35-7/8”Wx12”D
ZV371, ZV370 ZX12DC30 12”Hx29-7/8”Wx12”D
• Order the duct cover accessory at the same time as the
vent hood and have on site before installation. Be sure to
order the duct cover corresponding to your model.
DUCTWORK ACCESSORIES
(for 48" wide models only)
Transition duct pieces are available for 48" wide
models. These pieces fit over the outlet on top
of the hood and will fit into a soffit or can be
concealed with a 12" duct cover.
ZX48AY, transition to
10" round for vertical exhaust
ZX48BY, transition to
10" round for horizontal exhaust
4-1/2"
10"
18-1/2"
8-3/4"
Optional 6" or 12"
Duct Cover
Optional 6" or 12"
Duct Cover
8-1/4"
4-1/2" 18-1/2"
C
12"
L
6-5/8"
toC
L

Especificaciones del producto

Marca: GE
Categoría: campana extractora
Modelo: ZV681YSS

¿Necesitas ayuda?

Si necesitas ayuda con GE ZV681YSS haz una pregunta a continuación y otros usuarios te responderán




campana extractora GE Manuales

campana extractora Manuales

Últimos campana extractora Manuales