Gigabyte GA-H270-HD3P Manual de Usario

Gigabyte Placa madre GA-H270-HD3P

Lee a continuación 📖 el manual en español para Gigabyte GA-H270-HD3P (18 páginas) en la categoría Placa madre. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/18

- 1 -

Table of Contents

Conguring a RAID Set (Intel® Z270/H270 Series) .........................................................2

1-1 Conguring SATA Controllers ............................................................................. 2

1-2 Installing the SATA RAID/AHCI Driver and Operating System.......................... 16

- 2 -

Conguring a RAID Set (Intel® Z270/H270 Series)

To create a RAID set, follow the steps below:

A. Install SATA hard drive(s) in your computer.

B. Congure SATA controller mode in BIOS Setup.

C. Congure a RAID array in RAID BIOS. (Note 1)

D. Install the SATA RAID/AHCI driver and operating system.

Before you begin, please prepare the following items:

•At least two SATA hard drives or SSDs (Note 2) (to ensure optimal performance, it is recommended that you

use two hard drives with identical model and capacity). (Note 3)

•A Windows setup disk.

•Motherboard driver disk.

•A USB thumb drive.

RAID Levels

1-1 Conguring SATA Controllers

A. Installing hard drives

Install the hard drives/SSDs in the Intel® Chipset controlled connectors on the motherboard. Then connect

the power connectors from your power supply to the hard drives.

RAID RAID RAID RAID 0 1 5 10

Minimum

Number of Hard

Drives

≥2 ≥32 4

Array Capacity Number of hard

drives * Size of the

smallest drive

Size of the smallest

drive

(Number of hard

drives -1) * Size of

the smallest drive

(Number of hard

drives/2) * Size of the

smallest drive

Fault Tolerance No Yes Yes Yes

(Note 1) Skip this step if you do not want to create RAID array on the SATA controller.

(Note 2) An M.2 PCIe SSD or an U.2 SSD cannot be used to set up a RAID set either with an M.2 SATA SSD

or a SATA hard drive.

(Note 3) Refer to Chapter 1, "Internal Connectors," for the installation notices for the U.2, M.2, and SATA

connectors.

- 3 -

The BIOS Setup menus described in this section may differ from the exact settings for your motherboard.

The actual BIOS Setup menu options you will see shall depend on the motherboard you have and

the BIOS version.

B. Conguring SATA controller mode in BIOS Setup

Make sure to congure the SATA controller mode correctly in system BIOS Setup.

Step 1:

Turn on your computer and press <Delete> to enter BIOS Setup during the POST (Power-On Self-Test). Go to

Peripherals\SATA And RST Conguration SATA Controller(s), make sure is enabled. To create RAID, set

SATA Mode Selection Intel RST Premium With Intel Optane System Acceleration to (Figure 1).

Step 2:

To use the EZ RAID feature, follow the steps in "C-1." To congure UEFI RAID, follow the steps in "C-2." To

enter the legacy RAID ROM, refer to "C-3" for more information. Finally, save the settings and exit BIOS Setup.

Figure 1

Especificaciones del producto

Marca:	Gigabyte
Categoría:	Placa madre
Modelo:	GA-H270-HD3P
Peso.:	660 g
Ancho:	93 mm
Profundidad:	126 mm
Altura:	149 mm
Amable:	Koeler
Nivel de ruido (baja velocidad):	13.5 dB
Nivel de ruido (alta velocidad:	24.8 dB
Herramientas de montaje:	Ja
Flujo de aire:	86.5 m³/uur
numero de fans:	1 ventilator(en)
Potencia de diseño térmico (TDP):	170 W
Velocidad de rotación (máx.):	1600 RPM
Incluyendo tornillos:	Nee
Número de tornillos:	14
Velocidad de rotación (mín.):	500 RPM
Ubicación adecuada:	Processor
Procesadores compatibles:	AMD A, AMD Athlon, Intel Celeron, Intel Core i3, Intel Core i5, Intel Core i7, Intel Pentium
Código del Sistema Armonizado (SA):	84733080
Diámetro del ventilador:	120 mm
Zócalos de procesador compatibles:	LGA 1150 (Socket H3), LGA 1151 (Socket H4), LGA 1155 (Socket H2), LGA 1156 (Socket H), LGA 1366 (Socket B), LGA 775 (Socket T), Socket AM2, Socket AM2+, Socket AM3, Socket AM3+, Socket AM4, Socket FM1
Soporte de modulación de ancho de pulso:	Ja
tipo de acción:	Vloeistof dynamisch lager (FDB)
Material de aleta:	Aluminium
Número de tubos de calor:	4
Ventilador de alimentos (ancho x fondo x alto):	120 x 25 x 120 mm
Diámetro de los tubos de calor:	6 mm
Dimensiones del disipador de calor (An x Pr x Al):	68 x 126 x 149 mm
Conector del ventilador:	4-pin
Desde Koelpa:	Ja
Tensión nominal del ventilador:	12 V