Gigabyte GA-Z270X-UD3 Manual de Usario

Gigabyte Placa madre GA-Z270X-UD3

Lee a continuación 📖 el manual en español para Gigabyte GA-Z270X-UD3 (18 páginas) en la categoría Placa madre. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/18

- 1 -

Table of Contents

Conguring a RAID Set (Intel® Z270/H270 Series) .........................................................2

1-1 Conguring SATA Controllers ............................................................................. 2

1-2 Installing the SATA RAID/AHCI Driver and Operating System.......................... 16

- 2 -

Conguring a RAID Set (Intel® Z270/H270 Series)

To create a RAID set, follow the steps below:

A. Install SATA hard drive(s) in your computer.

B. Congure SATA controller mode in BIOS Setup.

C. Congure a RAID array in RAID BIOS. (Note 1)

D. Install the SATA RAID/AHCI driver and operating system.

Before you begin, please prepare the following items:

•At least two SATA hard drives or SSDs (Note 2) (to ensure optimal performance, it is recommended that you

use two hard drives with identical model and capacity). (Note 3)

•A Windows setup disk.

•Motherboard driver disk.

•A USB thumb drive.

RAID Levels

1-1 Conguring SATA Controllers

A. Installing hard drives

Install the hard drives/SSDs in the Intel® Chipset controlled connectors on the motherboard. Then connect

the power connectors from your power supply to the hard drives.

RAID RAID RAID RAID 0 1 5 10

Minimum

Number of Hard

Drives

≥2 ≥32 4

Array Capacity Number of hard

drives * Size of the

smallest drive

Size of the smallest

drive

(Number of hard

drives -1) * Size of

the smallest drive

(Number of hard

drives/2) * Size of the

smallest drive

Fault Tolerance No Yes Yes Yes

(Note 1) Skip this step if you do not want to create RAID array on the SATA controller.

(Note 2) An M.2 PCIe SSD or an U.2 SSD cannot be used to set up a RAID set either with an M.2 SATA SSD

or a SATA hard drive.

(Note 3) Refer to Chapter 1, "Internal Connectors," for the installation notices for the U.2, M.2, and SATA

connectors.

- 3 -

The BIOS Setup menus described in this section may differ from the exact settings for your motherboard.

The actual BIOS Setup menu options you will see shall depend on the motherboard you have and

the BIOS version.

B. Conguring SATA controller mode in BIOS Setup

Make sure to congure the SATA controller mode correctly in system BIOS Setup.

Step 1:

Turn on your computer and press <Delete> to enter BIOS Setup during the POST (Power-On Self-Test). Go to

Peripherals\SATA And RST Conguration SATA Controller(s), make sure is enabled. To create RAID, set

SATA Mode Selection Intel RST Premium With Intel Optane System Acceleration to (Figure 1).

Step 2:

To use the EZ RAID feature, follow the steps in "C-1." To congure UEFI RAID, follow the steps in "C-2." To

enter the legacy RAID ROM, refer to "C-3" for more information. Finally, save the settings and exit BIOS Setup.

Figure 1

Especificaciones del producto

Marca:	Gigabyte
Categoría:	Placa madre
Modelo:	GA-Z270X-UD3
Color del producto:	Zwart
Amable:	AV-zender & ontvanger
Indicadores LED:	Ja
Bluetooth:	Nee
Actual:	2 A
Modos de vídeo compatibles:	1080i, 1080p, 480p, 720p
Resolución Máxima:	1920 x 1080 Pixels
Incluye adaptador de CA:	Ja
Certificación:	FCC, CE
Conexión para adaptador de red:	Ja
Certificados de sostenibilidad:	RoHS
Temperatura de almacenamiento:	-20 - 60 °C
Entrada de video:	1
Adaptación externa:	Ja
Productos compatibles:	SIIG CE-DP0611-S1 / CE-DP0811-S1/ CE-H22711-S1 / CE-H22911-S1
Entrada HDMI:	1
Puertos de salida RJ-45:	1
Vídeo apagado:	1
Número de salidas HDMI:	1
Configuración del receptor (B x D x H):	115 x 27.9 x 90.9 mm
Puertos de entrada RJ-45:	1
Tensión de funcionamiento:	5 V
Rango-maximo:	100 m
Wifi.:	Nee
voltaje-de-entrada-de-CA:	100-240 V
Frecuencia-de-entrada-de-CA:	50 - 60 Hz
Temperatura de funcionamiento (TT):	0 - 50 °C
Peso del receptor:	340 g
Dimensiones del transmisor (AnxPrxAl):	115 x 27.9 x 90.9 mm
Peso del transmisor:	350 g
Tipos de cables compatibles:	Cat5e, Cat6
Tipo-de-conección:	19-pin HDMI, 3.5mm Jack (IR)