Hager 75441389 Manual de Usario

Hager No categorizado 75441389

Lee a continuación 📖 el manual en español para Hager 75441389 (5 páginas) en la categoría No categorizado. Esta guía fue útil para 13 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/5
CO2-sensor
Order No. : 754413xx
Operation- and
Assembly Instructions
1 Safety instructions
Electrical equipment may only be installed and fitted by electrically skilled persons.
Failure to observe the instructions may cause damage to the device and result in fire and
other hazards.
Do not use for safety-related gas measurements.
During renovation work, protect the device against soiling through paint, wallpaper
paste, dust, etc. Device can be damaged.
Only operate the device with cover. Device fault possible due to electrostatic discharge.
Do not clean or store the device with organic solvents or expose it to their vapours. Do
not stick any adhesive labels. Do not store device in packaging or environments that
contain softening agents, e.g. bubble wrap or polystyrene. Before starting renovation
work, remove the device from the system and store it in a suitable place. The function of
the humidity sensor may be permanently impaired.
Danger of electric shock on the KNX installation. Do not connect any external voltage to
the inputs. Doing so may damage the device(s), and the SELV potential on the KNX bus
line will no longer be available.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
Figure 1: Device overview
(1) Terminal insert
(2) Design frame
(3) Electronics cover
(4) Cover
(5) Programming button and LEDs
(6) Locking screw (plastic)
(7) Sensor window CO2 sensor
Page 1/5
CO2-sensor
32577101
6LE001510A 14.07.2015
KNX
3 Function
System information
This device is a product of the KNX system and complies with the KNX directives. Detailed
technical knowledge obtained in KNX training courses is a prerequisite to proper understanding.
The function of this device depends upon the software. Detailed information on loadable
software and attainable functionality as well as the software itself can be obtained from the
manufacturer´s product database. Planning, installation and commissioning of the device are
carried out with the aid of KNX-certified software. The latest versions of product database and
the technical descriptions are available on our website.
Intended use
- Measurement of CO2 concentration, relative air humidity and air temperature
- Output of the measured values as telegram to the bus, e.g. for controlling fans or window
drives via KNX telegrams
- Single-room temperature control in KNX installations
- Installation in appliance box according to DIN 49073
Product characteristics
- Limit value monitoring for CO2 concentration and air humidity
- Dew point alarm for, for example, cooling blankets and conservatories, to avoid possible
mould formation
- Two binary inputs for connection of potential-free contacts e.g. buttons, switches, window
contacts
- Logic gates for simple gating functions
Function CO2 sensor:
- Max of 4 different adjustable threshold values
- Adaptation to current elevation above sea level (a.s.l.)
iAfter switch-on, the CO2 sensor requires a warm-up period of up to 5 minutes, until normal
operation is reached.
Function Room temperature controller:
- Measurement of room temperature and comparison with setpoint temperature
- Setpoint setting by selection of the operating mode
- Operating modes Comfort, Standby, Night operation, Frost/heat protection
- Heating and cooling mode with basic and auxiliary level
Function of humidity sensor:
- Max of 2 adjustable threshold values
iThe device contains a sensitive, integrated humidity/temperature sensor. Longer storage at
a higher or lower temperature or humidity leads to inaccuracies of the humidity reading.
This difference is rectified again after a few days in operation.
Function Binary inputs:
- Functions: dimming, shutter control, light scene extension unit, brightness or temperature
value transmitter.
- Inputs lockable in operation
4 Information for electrically skilled persons
4.1 Fitting and electrical connection
DANGER!
Electrical shock on contact with live parts in the installation environment.
Electrical shocks can be fatal.
Before working on the device, disconnect the power supply and cover up live
parts in the working environment.
Mounting and connecting the device
Do not use the device in multiple combinations with electrical devices. Their heat generation
influences the temperature and humidity reading of the controller.
Page 2/5 14.07.2015
32577101
6LE001510A
KNX
CO2-sensor
Do not mount the device near sources of interference such as electric cookers, refrigerators,
draughts or direct sunlight. This influences the temperature and humidity reading of the
controller.
Observe routing conditions for SELV.
Do not route input cables parallel to mains cables. Otherwise there might be EMC interference.
Recommendation: Use deep accessory sockets.
The optimum installation height is approx. 1.5 m.
oRemoving the cover (4).
oIsolate terminal insert (1) from electronic insert (3).
oConnect the bus line to the connection terminal (9) in the terminal insert.
oBinary inputs: Connect window contacts, NO contact or NC contact button to terminals 4, 5
and 6 of the connecting strip (8) (Figure 3).
oInsert terminal insert (1) in appliance box. Note label . The bus connectionOBEN / TOP
must be to the right and below.
oFit the Design frame (2) on terminal insert (1).
oInsert the electronics cover (3) into the terminal insert in the correct orientation.
DANGER!
When mounting with 230 V devices under a common cover, e.g. socket outlets,
there is a danger of electrical shocks in the event of a fault!
Electrical shocks can be fatal.
Only use the preassembled plastic screw as locking screw!
oFasten the electronics cover with the locking screw (6).
oReattach the cover (4)
Figure 2: Terminal insert with connections
(8) Connecting strip binary inputs
(9) KNX connection
Page 3/5 14.07.2015
32577101
6LE001510A
KNX
CO2-sensor

Especificaciones del producto

Marca: Hager
Categoría: No categorizado
Modelo: 75441389

¿Necesitas ayuda?

Si necesitas ayuda con Hager 75441389 haz una pregunta a continuación y otros usuarios te responderán


No categorizado Hager Manuales

Hager

Hager Vision VKG004A-T Manual de Usario

27 Octubre 2024
Hager

Hager VM206 Manual de Usario

13 Octubre 2024
Hager

Hager NCN110A Manual de Usario

11 Octubre 2024
Hager

Hager NCN303A Manual de Usario

9 Octubre 2024
Hager

Hager VM202K Manual de Usario

9 Octubre 2024
Hager

Hager BD163T Manual de Usario

8 Octubre 2024
Hager

Hager JK116BA3 Manual de Usario

4 Octubre 2024
Hager

Hager JK108BSH Manual de Usario

4 Octubre 2024
Hager

Hager VML406AH Manual de Usario

3 Octubre 2024
Hager

Hager JKD188TM Manual de Usario

27 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024