Haier HSU-24HEG03/R2(DB) Manual de Usario

Haier aire acondicionado HSU-24HEG03/R2(DB)

Lee a continuación 📖 el manual en español para Haier HSU-24HEG03/R2(DB) (8 páginas) en la categoría aire acondicionado. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/8

Please read this operation manual before using the air conditioner.

●

Keep this operation manual for future reference.

SPLIT TYPE ROOM AIR CONDITIONER

OPERATION MANUAL

0010538410

HSU-09HEG03/R2(DB)

Contents

PARTS AND FUNCTIONS

OPERATION

MAINTENANCE

CAUTIONS

TROUBLE SHOOTING 7

HSU-12HEG03/R2(DB)

HSU-18HEG03/R2(DB)

HSU-24HEG03/R2(DB)

HSU-09HEK03/R2(DB)

HSU-12HEK03/R2(DB)

HSU-18HEK03/R2(DB)

HSU-24HEK03/R2(DB)

Outdoor Unit



Loading of the battery

Parts and Functions

Indoor Unit

OUTLET

INLET

CONNECTING PIPING AND ELECTRICAL WIRING

DRAIN HOSE

Remote controller

Remove the battery cover;

Load the batteries as illustrated.

2 R-03 batteries, resetting key

(cylinder);

Be sure that the loading

is in line with th

e" + "/"-";

Load the battery,then put on the cover again.

The distance between the signal transmission head and the rece-

iver hole should be within 7m without any obstacle as well.

When electronic-started type fluorescent lamp or change- over

wireless telephone is installed in the

ver is apt to be disturbed in receiving the signals,

so the distance to the indoor unit should be shorter.

type fluorescent lamp or

room, the recei

Note:

Full display or unclear display during operation indicates the

ries have been used up. Please change batteries.

If the remote controller can't run normally during operation, please

reload several minutes later.

batte

remove the batteries and

Please be subject to the actual produce purchased the

above picture is just from your reference

Hint:

Remove the batteries in case won't be in use for a long period. If

there is any display after taking-out, just press reset key.

Please be subject to the actual produce purchased the

above picture is just from your reference

1. Mode display

2. Signal sending display

4. FAN SPEED display

5. LOCK display

6. TIMER OFF display

TIMER ON display

LO MED HI

7.TEMP display

16. LOCK button

Used to lock buttons and LCD display.

25. RESET button

When the remote controller

appears abnormal, use a sharp

pointed article to press this button

to reset the remote

22. HOUR button

Operation mode AUTO FANCOOL DRY

Remote controller

HEAT

Control the lightening and extinguishing

of the indoor LED display board.

3. SWING display

9. QUIET button

10. HEAT button

11. COOL button

12. AUTO button

13. FAN SPEED button

14. TIMER button

15. HEALTH button

17. LIGHT button

18. POWER ON/OFF button

19. DRY button

20. TEMP button

21. SWING button

23. EXTRA FUNCTION button

24.CANCEL/CONFIRM button

AUTO

Function: Setting and cancel to the

timer and other additional functions.

Display

circulated

Operation mode

Remote controller

QUITE POWERSLEEP

Supplemented

electrical

heating HEALTH

Additional functions display

Healthy function is not available for some units.

Function: Air sending--- Healthy

airflow position1--- Healthy airflow

position 2 --- Restore the original

flap position --- Right & left air airflow

--- A-B yard---10 and heating symbol

displayed simultaneously--- Sleeping

--- Electrical heating--- Refresh air

(reserved function) --- Power ---

Fahrenheit/Celsius mode conversion

Air Purifying Filter(inside)

Inlet

1Inlet grille

Outlet

(adjust left and right air flow)

Vertical blade

Display board

Horizontal flap

(adjust up and down air flow.

Don't adjust it manually) Emergency Switch

6 5 7

EK3

5 86 7

EK1 display board

EK3 display board

Display board

When receiving the remote control

signal,display the set temperature

and in the rest time the room

temperature is displayed and this

room temperature is only for reference.

Signal receiver hole

ON/OFF display

Ambient temp.display

TIMER ON/OFF display

TIMER ON-OFF display

SLEEP display

Note to the power failure resume:

Press the sleep button ten times in five seconds and enter function

after hearing four sounds.And press the sleep button ten times

within five seconds and leave this function after hearing two sounds.

EK1

COOL\HEAT\DRY\AUTO display

6RUNNING display

Operation

Air Flow Direction Adjustment

Press FAN button. For each press, fan speed

follows:

Remote controller:

Press button

Every time the button is pressed, temp.setting

increase 1o

C,if kept depressed, it will increase

rapidly

Every time the button is pressed, temp.setting

decrease 1

oC,if kept depressed, it will

decrease rapidly

Select a desired temperature.

4.Fan speed selection

3.Select temp.setting

Air conditioner is running under displayed fan speed.

When FAN is set to AUTO, the air conditioner

automatically adjusts the fan speed according to room

temperature.

1. Unit start

Press ON/OFF on the remote controller, unit starts.



Base Operation

Remote controller

1.Status display of air flow

When restart after remote turning off, the remote

memorize the previous

Move the vertical blade by a knob on air

to adjust left and right direction referring to Fig.

2.Left and right air flow adjustment(manual)

Cautions:

When adjusting the flap by hand,turn off the unit.

When humidity is high,condensate water might occur

adjusted to left or

It is advisable not to keep horizontal flap at downward

position for a long time in COOLor DRY

otherwise, condensate water might occur.

conditioner

Emergency operation and test operation

at air outlet if all vertical louvers are

right.

mode ,

controller will automatically

Note:

set swing position.

changes as

Operation

Mode

Remote

Controller Note

In DRY mode, when room temperature becomes lower

than temp.setting+2oC, unit will run intermittently at LOW

speed regardless of FAN setting.

Under the mode of auto operation, air conditioner will

automatically select Cool or Heat operation according to

room temperature. When FAN is set to AUTO the air

conditioner automatically adjusts the fan speed according

to room temperature.

In FAN operation mode , the unit will not operate in COOL or

HEAT mode but only in FAN mode, AUTO is not available in

FAN mode. And temp. setting is disabled. In FAN mode,

sleep operation is not available.

Emergency Operation:

Use this operation only when the remote controller is defective

or lost, and with function of emergency running, air conditoner

can run automatically for a while.

When the emergency operation switch is pressed, the " Pi "

sound is heard once, which means the start of this operation.

When power switch is turning on for the first time and

emergency operation starts, the unit will run automatically in

the following modes:

Room

temperature Designated

temperature

Timer

mode Fan

speed

Operation

mode

Above 23 oC

Below 23 o

C 23 oC

26oC

AUTO

COOL

HEAT

It is impossible to change the settings of temp. and fan speed,It

is also not possible to operate in timer or dry mode.

temperature is below 16oC, do not use it in the

Test operation:

Use this switch in the test operation when the room

normal operation.

your finger from the switch: the cooling

Continue to press the test operation

switch for more than 5 seconds . After

you hear the "Pi" sound twice, release

Test operation switch is the same as emergency switch.

operation starts with the air flow speed "Hi".

Under this operation mode,the fan motor of indoor

unit will run in high speed.







LOW MED HI AUTO

2. Select operation mode



COOL button:Cooling mode

HEAT button: Heating mode

DRY button: Dehumidify mode

Display

circulated

DRY

COOL

AUTO

HEAT

FAN

In HEAT mode, warm air will blow out after a short

period of the time due to cold-draft prevention function.

When FAN is set to AUTO, the air conditioner automatically

adjusts the fan speed according to room temperature.

test operation

switch

Pi Pi

emergency

operation switch

'

Pos.1 Pos.2 Pos.3

Pos.4 Pos.5 Pos.6 (Auto swing)

cooling mode:from pos.1 to pos.4 and pos.6

heating mode:from pos.5 to pos.1 and pos.6

Especificaciones del producto

Marca:	Haier
Categoría:	aire acondicionado
Modelo:	HSU-24HEG03/R2(DB)
Tipo de operación:	Air switch, Wall switch
Color del producto:	Grey, Stainless steel
Peso.:	10000 g
Ancho:	220 mm
Altura:	311 mm
Amable:	Afvalverwerkingssysteem voor gootstenen
Actual:	9.5 A
Contenido:	1005 ml
Velocidad de rotación:	1725 RPM
voltaje-de-entrada-de-CA:	110 - 240 V
Frecuencia-de-entrada-de-CA:	50 - 60 Hz
Potencia-del-motor:	0.75 hp
Tamaño del fregadero:	1.5 "
Tipo de tránsito:	Doorlopende toevoer