Haier HW-12LN13 Manual de Usario

Haier aire acondicionado HW-12LN13

Lee a continuación 📖 el manual en español para Haier HW-12LN13 (2 páginas) en la categoría aire acondicionado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

Please read this operation manual before using the air conditioner

Please keep it attentively

0010515219

Applicable ambient temperature range:

OPERATION CONDITIONS

D.B :Dry Bulb Temperature W.B :Wet Bulb Temperature

AIR CONDITIONER OPERATION

D.B W.B D.B W.B D.B W.B D.B W.B

Max.Temperture:

℃

Min.Temperture:

℃

/18

℃

Cooling

Indoor

Outdoor

Indoor

Outdoor

It is advisable not to keep flap at downward position for a long time in COOL mode,vertical

otherwise , condensate water might occur.

Don't move the horizontal flap with hand in order to avoid the vertical flap abnormal, using the

remote controller to adjust the move of vertical flap.

HW-07LN03 HW-09LN03 HW-12LN03

HW-09C2 HW-12C1

HW-12LNA03 HW-09LN13 HW-12LN13

HW-09CA2 HW-12CA2

OPERATION MANUAL

ROOM AIR CONDITIONER

HW-09LNA03

HINTS

Compressor won’t start in FAN mode ,only

fan motor will run at selected speed.

CAUTION

The compressor may cycle for 10 minutes on and 6 minutes off in Dehumid mode.

Air blown out will be very cold at relatively low room temp..

Machine body

Front panel

Air inlet

(indoor side)

Air outlet

(indoor side)

Air inlet

(outdoor side)

Control

panel

Air filter (inside)

Machine body

Power plug

Take out the air filter

Clean the filter

Hump

When dirt accumulates on air filter, air

circulation will be blocked, which causes

poor cooling. It is advisable to clean air

filter every two weeks for longer operation.

1.Press the concave parts on

both sides at the lower part of

air inlet grille to open the air

inlet grille.

2.Hold the hump of filter mesh

with fingers (as illustrated) and

take it out.

1.Gently flap the dirt off the air filter.

2.Carefully wash air filter in warm water(below 40°C To ).

obtain better cleaning effect,soap water or neutral detergent

may be used.

3.Flush air filter carefully with clean water after removing

dirt.Let it dry completely.

CAUTION

To protect unit system, don’t restart until

3 minutes have elapsed.

If the unit has been running under large

humidity for a long time, dew might occur

at outlet grille.

CAUTION

PART INDENTIFICATION

Remote controller Controll panel

Cooling operation

Fan operation

1.Press MODE button.For each press,operation

mode changes as follows:

When the COOL display light bright,A/C will be

working under the cooling function.

2.Select temp.setting, by using “ ” or“ ”

button.

“ ” Each press will increase temp. setting by 1.

“ ” Each press will decrease temp. setting by 1.

3.If you choose the FAN SPEED mode you can run

the fan in one of the 2 speeds: HI or LO.

Change air flow direction if necessary.

1.POWER

Press it to start unit and press it again to stop.

2.MODE:

Used to select operation mode:FAN COOL DEHUM

3.FANSPEED:

Used to select desired fan speed :HIGH or LOW.

4.TIMER

Used for TIMER start or stop.

5.TEMP.or TIME set

Used to set TIME or TEMP.setting.

6.E-S

ENERGY SAVER

7.SWING

Used to activate the vertical louver .This will give

you an even airflow througout the room.

8.ENERGY SAVER

9.TEMP./TIME display

In some days you may want to run the

“Fan”function.

1.Press MODE button.

When the FAN display light bright, A/C will be

working under the fan function.

2.Fan speed selection:

Here the fan runs only at Hi or Lo speed.

Change air flow direction if necessary

Timer operation

With this function, unit will start or stop at the

time you want.

1.Start unit and select desired operation mode.

2.Select Timer function

Timer On or Off stop mode is used to preset or

shut off your unit in advance .

You can program this up to 24 hours in

advance. You can use the Timer in 3 function

i.e Cool Dehumid or Fan only. Selected

desired mode. (TIMER On or Off stop )

Timer On

Unit must be on to set the timer. Unit will shut

down automatically after it accepts the setting

in 5 seconds. Use this mode to preset the start

time of the unit 24 hours in advance .

a) Press “On” of remote controller or “TIMER”

of control panel,LED display will show “01”.

(Electrify for the first time)

b) Set desired number by pressing the

( )pad of the Temp/Time buttons. One for

each hour . If you passed the desired time use

the ( ) pad key to lower the selection.

Timer Off

Unit must be running to set the timer off. Use

this to preset the time you would like the unit to

shut off.

a) Press “off” of remote controller or “TIMER”of

control panel,LED display will show

“01”.(Electrify for the first time)

b) Set desired number by pressing the

( ) pad of p1-he Temp/Time buttons. One for

each hour . If you passed the desired time use

the ( ) pad key to lower the selection.

When using the timer the unit will use/revert to

the last A/C , fan settings when activated . The

timer must be reset every time you choose to

use it .

OPENCLOSE

The ventilation lever must be

CLOSE position in order to

maintain the best cooling

conditions. When fresh air is

necessary in the room, set the

ventilation lever to the OPEN

position. The damper is

opened and room air is

exhausted.

Airflow Direction Vane

T t he horizon al air dire ionct is

adjus ingted b ey s tt the

AUTO SWING on.

The Vertical Airflow Direction

Vane is manually controlled

by positioning the vane to

discharge the air

upward,downward or straight

out.

Vertical airflow direction

Ventilation

Air filter cleaning

Airflow Direction

Ventilation

Do not raise the front panel

any higher than 70° to the

unit or damage to the tabs

may occur.

CAUTION

Before cleaning, turn off

the power

CONTENTS

Safety precautions....................1

Air conditioner operation ..........2

Care and Maintenance ............5

Air conditioner installation........6

Troubleshooting.......................8

SAFETY PRECAUTION

Do not install,remove and reinstall the unit yourself.

Improper installation may cause

leakage,electric shock or fire.Please engage an authorized dealer or specialist for the installation work.

The room air conditioner must be earthed.

Do not touch or operate with wet hands.

Do not turn on the unit by inserting the power plug.Do not switch off the unit by pulling out

the power plug.

Do not insert sticks,fingers or other objects into the unit.

If the supply cord is damaged, it must be replaced by the manufacturer or its service agent

or a similar qualified person.

After installation, the power plug should be easily reached.

The wiring method should be in line with the local wiring standard.

CAUTION

DEHUMID mode

If you need to only remove the moisture press the

Dehumind button.

1.Press MODE button.

When the DEHUM display light bright, A/C will be

working under the dehumidify function.

2.Select temp.setting, by using “ ” or“ ” button.

“ ” Each press will increase temp. setting by 1°C.

“ ” Each press will decrease temp. setting by 1°C.

3.If you choose the FAN SPEED mode you can run

the fan in one of the 2 speeds: HI or LO.

Air conditioner is running under displayed fan speed.

In DRY mode, when room temperature becomes

lower than temp. setting +2°C, unit will intermittently

at LOW speed regardless of FAN setting.

Change air folw direction if necessary.

ENERGY SAVER operation

1.Select operation mode

Press MODE button. Then select COOL operation

Saving energy function only can be used when A/C

working on cooling condition.

2. ENERGY SAVER selection

When this feature is “On”, the fan will shut off three

minutes after the compressor cycles off. This will

reduce energy consumption and noise. When the

compressor turns back on, the fan will turn on at the

same time. In the “Off” position , the fan will not shut

off when the compressor cycles off.

Remote controller’s operation

When in use, put the signal transmission head

directly to the receiver hole on the indoor unit.

Don’t throw the controller, prevent it from being

damaged.

When electronic-started type fluorescent lamp

or change-over type fluorescent lamp or

wireless telephone is installed in the room, the

receiver is apt to be disturbed in receiving the

signals so the distance to the indoor unit should

be shorter.

2 3 9 4 7 5

15-25

15-25mm

HW-09C2

HW-12C1

HW-09LN13 HW-09CA2

HW-09LNA03

HW-09LN03HW-07LN03

HW-12LN13

HW-12CA2

Power failure resume:

If sudden power failure occurs,the unit will resume original operation when power is supplied again.

NOTE:

When sudden power failure happens during unit operation in power failure mode,if the air

conditioner is not desired for use in a long period,please shut off the power supply in case

that the unit automatically resume operation when power is re-supplied.

Especificaciones del producto

Marca:	Haier
Categoría:	aire acondicionado
Modelo:	HW-12LN13
Tipo de operación:	Knoppen
Ancho:	437 mm
Profundidad:	377 mm
Altura:	44 mm
Peso del embalaje:	6250 g
Color-de-la-carcasa.:	Zwart
Número de puertos Ethernet LAN (RJ-45):	1
Consumo de energía (máx.):	- W
HDCP:	Ja
Soporte HDR:	Ja
Puerto RS-232:	1
Número de puertos de entrada HDMI:	6
Entrada remota (IR):	7
Temperatura de almacenamiento:	-25 - 70 °C
Montaje en bastidor:	Ja
Salida remota (IR):	6
Versión HDCP:	2.0
Número de puertos de salida HDMI:	7
Capacidad del bastidor:	1U
voltaje-de-entrada-de-CA:	100 - 240 V
Temperatura de funcionamiento (TT):	-5 - 55 °C
Tipo-producto:	AV-matrixschakelaar
Submuestreo de croma admitido:	4:4:4, 4:2:0