Halifax FTHP530 Manual de Usario

Halifax campana extractora FTHP530

Lee a continuación 📖 el manual en español para Halifax FTHP530 (4 páginas) en la categoría campana extractora. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

Revised 10/2019

Receiving and Storage

Once equipment is received, check for both obvious and hidden damage. If damage is found, record all

necessary informaon on the bill of lading and le a claim with the nal carrier. Check to be sure that

all parts of the shipment, including accessories, are accounted for.

UNPACKING

Verify that all required parts and the correct quanty of each item have been received. If any items are

missing, report shortages to your representave to obtaining missing parts. Somemes it is not possi-

ble that all items for the unit be shipped together due to availability of transportaon and truck space.

Conrmaon of shipment(s) must be limited to only items on the bill of lading. Filters are typically

shipped in the hood, but somemes are shipped on a separate skid in their original packaging. Do not

remove factory packaging or install lters unl just prior to commissioning. Remove all other shipping/

packing materials.

WARNING!!

Installaon of this unit should only be performed by a qualied professional.

Please read the instrucons thoroughly before installing or servicing this equipment.

LISTING

This hood is listed to ANSI UL710 and CAN/ULC S646-10 and built to the “NFPA 96” Naonal Fire

Protecon Associaon Standard

WARRANTY

This equipment is warranted to be free from defects in materials and workmanship, under normal use

and service, for a period of 24 months from date of shipment – See full Installaon Instrucons for

Details.

INSTALLATION

It is necessary to install and operate this unit with the airow (CFM) designed for the size of hood,

lters and installaon based on the informaon provided.

SITE PREPERATION

1. To safely li equipment into the nal installed posion you must make sure the area of installaon

is clear. Make sure you have enough room aer installaon to service unit easily.

2. Verify the locaon that the hood will be installed so there is

nothing to interfere when installing

the unit.

3. Review your plans and specicaons for your project.

4. Conrm and verify the supports will support the weight of the

hood and fan mounted on top of the truck.

5. If installing light xtures

a. Have electrician following wiring diagram as noted in full

Installaon Manual

6. Weld Duct connecon on top of Hood at area which does not

interfere with bracing inside truck

7. Cut hole in Hood at duct connecon – See Figure #1, Item #7

8. To cut the hole properly in the roof of truck – See Figure #1

a. Li hood in the locaon where it will be mounted, ensuring

there is adequate room available to install the hood and all

ductwork to comply with proper clearances from combusble

material (Item # 1)

b. Bring duct in contact with top of truck (Item # 5)

c. Mark locaon of duct on truck roof

d. Lower hood back down

e. Cut hole in roof of truck (Item # 7)

9. Mount Roof Curb with Curb plate on top of truck

(Items # 3 & 4)

10. See aached instrucons for using Concession Hood Bolt Kit to

complete hood aachment

11. Curb Plate securing

a. Cut Curb Plate hole where duct meets plate to ensure ght t

b. Secure Curb Plate to top of Roof Curb

12. Install and secure fan on top of Roof Curb (Item # 2)

13. Wire power to Fan

14. Use Sealant around roof curb and any holes which were made during the installaon process

IMC, NFPA96 and local authories having jurisdicon may call for a minimum clearance (typically

18 inches for type 1, grease rated hoods) between the cooking hood(s), exhaust ducts, and building

materials which are combusble. However, IMC and NFPA96 do outline acceptable clearance

reducon methods; most local jurisdicng authories will accept the clearance reducon methods

approved in the manufacturer’s UL lisng for Type 1, grease rated hoods.

Especificaciones del producto

Marca:	Halifax
Categoría:	campana extractora
Modelo:	FTHP530
Color del producto:	Brown, White
Función de calentamiento:	Ja
Ancho del embalaje:	430 mm
Empaquetadura en profundidad:	260 mm
Altura del embalaje:	450 mm
Función de descongelación:	Ja
Activos:	900 W
Número de rebanadas:	1 snede(n)
Botón detener/cancelar:	Ja
Mecanismo de pan autocentrante:	Ja
Mecanismo de cabeza alta:	Ja
Bandeja recogemigas extraíble:	Ja
Almacenamiento de cable:	Ja
Luz indicadora:	Ja
Niveles de bronceado:	7
Número de cerraduras:	1
Control electrónico de dorado:	Ja
Bandeja para migas:	Ja
Rejilla para sándwiches:	Nee
Ranura larga:	Ja
Rejilla calefactora:	Nee
Mango(s) frío(s):	Ja
voltaje-de-entrada-de-CA:	230 V