Harman Kardon HTFS 2 Manual de Usario

Lee a continuación 📖 el manual en español para Harman Kardon HTFS 2 (4 páginas) en la categoría Vocero. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/4
HTFS 2
FLOOR STANDS
OWNERS MANUAL
Power for the Digital Revolution.
®
®
2 INTRODUCTION
INTRODUCTION
Introduction
Thank you for purchasing Harman Kardon
HTFS 2 floor stands. These stands are
designed to enhance your enjoyment
of a Harman Kardon HKTS 7 or HKTS 14
home cinema loudspeaker system by
expanding your speaker-placement options
to create the optimum audio presentation.
The HTFS 2 stands are also compatible
with Harman Kardon HKS 3 and HKS 4
loudspeakers.
To obtain maximum enjoyment of your
home theater system, we ask you to
spend a few minutes reading the speaker
placement and setup instructions in the
owner’s manual supplied with your loud-
speakers, and a few moments reviewing
the assembly instructions for your HTFS 2
floor stands. If you have any questions
about this product or its installation, or
about your loudspeakers, please contact
your Harman Kardon dealer, who is your
best local source of information.
Included
Two floor stand columns
Two mounting plates
Eight rubber pads
Eight floor spikes
Eight round Phillips-head screws
for assembling the stands (M5-0.8P,
19mm or #10-32, 3/4" long)
Two weighted bases
ASSEMBLY 3
ASSEMBLY
Assembly
1. If you will be placing the HTFS 2 stands
on a hard surface, such as a wood or
tile floor, attach four of the supplied
self-adhesive rubber pads to the
underside of the base in the recesses
as indicated in the drawing.
Place rubber pads or floor spikes here
2. If you will be using the HTFS 2 stands
on a carpeted surface, screw four of the
supplied floor spikes into the base using
the threaded inserts in the recesses as
shown in the drawing.
3. Following the instructions on pages 9
through 12 of the owner’s manual
provided with your HKTS system, thread
the appropriate speaker cable through
the hole in the center of the base, being
careful to avoid the two screw holes.
Then feed the cable through the length
of the column from the bottom until it
comes out the top.
4. Attach the column to the base using two
of the supplied screws.
5. Thread the speaker cable through
the hole in the center of the mounting
plate, being careful to avoid the three
screw holes.
6. Attach the mounting plate to the top of
the column using two of the supplied
screws. The mounting plate tab with the
third screw hole should sit on the higher
rim of the column.
Attaching the Speaker
to the Stand
1. Unscrew the bolt that attaches the black
shelf stand to the bottom of the speaker.
Store the stand in a safe place in case it
is needed for a future installation. The bolt
will be used to attach the speaker to the
floor stand mounting plate.
2. Insert the speaker wires into the terminals
on the bottom of the speaker, being care-
ful to observe the correct polarity.
3. Place the speaker on top of the mounting
plate with the remaining screw hole lined
up with the threaded insert on the bottom
of the speaker.
4. Insert the bolt that was used for the shelf
stand up through the remaining screw
hole and into the speaker.
Repeat the assembly and speaker attach-
ment processes for each floor stand in your
system, and adjust the final speaker place-
ment as indicated in the owner’s manual
supplied with the speakers. You are now
ready to enjoy your home theater system!
Remove
Stand
15mm
or 1/2"

Especificaciones del producto

Marca: Harman Kardon
Categoría: Vocero
Modelo: HTFS 2

¿Necesitas ayuda?

Si necesitas ayuda con Harman Kardon HTFS 2 haz una pregunta a continuación y otros usuarios te responderán




Vocero Harman Kardon Manuales

Vocero Manuales

Últimos Vocero Manuales