Havis C-MD-312 Manual de Usario

Lee a continuación 📖 el manual en español para Havis C-MD-312 (2 páginas) en la categoría No categorizado. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/2
C-HDM-312
C-HDM-200 SERIES
POLE MOUNT
4X 1/4" FLAT WASHER
4X 1/4" LOCK WASHER
4X 1/4-20 X 3/4" HEX BOLT
C-MD-312
CONSOLE
(TYPE VARIES)
4X 1/4" FLAT WASHER
4X 1/4" LOCK WASHER
4X 1/4"-20 X 3/4" HEX BOLT
2.125
2.125
.265
SURFACE MOUNTING INSTRUCTIONS
MD-312 MOTION DEVICE CAN BE MOUNTED TO ANY FLAT SURFACE, INCLUDING CONSOLE TOPS AND HDM POLES. IF SURFACE DOES NOT HAVE
PREDRILLED HOLES, USE THE DRILL TEMPLATE BELOW.
PLACE MD-310 SERIES ON TOP OF MOUNTING SURFACE, ALIGNING THE (4) THREADED
1.
HOLES OF MD-110 SERIES BASE WITH THE (4) 1/4" HOLES THROUGH MOUNTING SURFACE.
INSTALL THE (4) HEX BOLTS, LOCK WASHERS, AND FLAT WASHERS THROUGH MOUNTING
2.
SURFACE INTO THE THREADED HOLES OF THE MOTION DEVICE AS SHOWN IN THE
DIAGRAM BELOW.
TIGHTEN ALL HARDWARE, ENSURING LOCK WASHERS ARE FULLY COMPRESSED.
3.
75 JACKSONVILLE RD,
WARMINSTER, PA. 18974
1-800-524-9900
SIZE
SCALE: 1:6
SHEET 1 OF 2
DO NOT SCALE DRAWING
WEIGHT (LB): NA
TITLE:
DWG. NO.
C-MD-312-INST
REV
A
11-17
HAVIS, INC.
INSTALLATION AND ADJUSTMENT
INSTRUCTIONS, C-MD-312
PLASTIC COVER
NOT SHOWN IN THIS VIEW
5
RELEASE LEVER
PULL TO RELEASE
SLIDE TRAY
USING A 9/16" SOCKET, TIGHTEN/LOOSEN NUT 4 AS REQUIRED TO ACHIEVE DESIRED
SLIDING FORCE OF SLIDE TRAY.
KNOB CAN BE TIGHTENED TO LOCK SLIDE TRAY IN ANY POSITION. STORE WITH SLIDE
TRAY FULLY COLLAPSED AND KNOB TIGHTENED. KNOB CAN BE INSTALLED ON EITHER
SIDE OF DEVICE AT USER'S PREFERENCE.
UNIT ROTATION
REMOVE PLASTIC COVER BY PULLING UPWARDS TO UNSNAP SIDE CLIPS.
USING A 9/16" SOCKET, TIGHTEN/LOOSEN NUT 5 AS REQUIRED TO ACHIEVE DESIRED
ROTATIONAL FORCE OF DEVICE WHEN RELEASE LEVER IS PULLED.
REINSTALL PLASTIC COVER BY PUSHING DOWNWARD TO ENGAGE SIDE CLIPS.
4
KNOB
ALTERNATE KNOB LOCATION
A
DETAIL A
1
2
USER ADJUSTMENTS
3
STANDARD
180° ROTATION
(AS SHIPPED)
1,2
3
OPTIONAL
90° ROTATION
(ADD SUPPLIED 1/4"
HARDWARE AS SHOWN)
OPTIONAL
*360° ROTATION
(DO NOT USE 1/4" HARDWARE)
NOT RECOMMENDED FOR
DEVICES HEAVIER THAN A
KEYBOARD
MOTION DEVICE ROTATION
USING A 1/2" SOCKET, LOOSEN NUT 1 AND ADJUST NUT 2 WITH A 1/2" WRENCH AS
REQUIRED TO ACHIEVE DESIRED ROTATIONAL FORCE OF
MOTION DEVICE. RETIGHTEN NUT 1 WITH A 1/2" SOCKET WHILE RESTRICTING NUT 2
FROM TURNING WITH A 1/2" OPEN END WRENCH.
FOR MINOR ADJUSTMENT, TIGHTEN OR LOOSEN NUT 3 USING A 7/16" SOCKET.
75 JACKSONVILLE RD,
WARMINSTER, PA. 18974
1-800-524-9900
SIZE
SCALE: 1:5
SHEET 2 OF 2
DO NOT SCALE DRAWING
WEIGHT (LB): NA
TITLE:
DWG. NO.
C-MD-312-INST
REV
A
11-17
HAVIS, INC.
INSTALLATION AND ADJUSTMENT
INSTRUCTIONS, C-MD-312

Especificaciones del producto

Marca: Havis
Categoría: No categorizado
Modelo: C-MD-312

¿Necesitas ayuda?

Si necesitas ayuda con Havis C-MD-312 haz una pregunta a continuación y otros usuarios te responderán




No categorizado Havis Manuales

No categorizado Manuales

Últimos No categorizado Manuales