Hikvision DS-2CE16D5T-AVFIT3 Manual de Usario

Hikvision Cámara de vigilancia DS-2CE16D5T-AVFIT3

Lee a continuación 📖 el manual en español para Hikvision DS-2CE16D5T-AVFIT3 (4 páginas) en la categoría Cámara de vigilancia. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

1 Introduction

1.1 Product Features

1.2 Overview

2 Installation

Before you start:

Thank you for purchasing our product. If there

are any questions, or requests, please do not

hesitate to contact the dealer.

This manual applies to DS-2CE56C5T-VFIT3 and

DS-2CE16C5T-(A)VFIR3.

This manual may contain several technical

incorrect places or printing errors, and the

content is subject to change without notice.

The updates will be added to the new version of

this manual. We will readily improve or update

the products or procedures described in the

manual.

DISCLAIMER STATEMENT

Underwriters Laboratories Inc. (”UL” has not)

tested the performance or reliability of the

security or signaling aspects of this product.

UL has only tested for fire, shock or casualty

hazards as outlined in Ul’s Standard(s) for Safety,

UL60950-1. UL Certification does not cover the

performance or reliability of the security or

signaling aspects of this product. UL MAKES NO

REPRESENTATIONS, WARRANTIES OR

CERTIFICATIONS WHATSOEVER REGARDING

0100001040603

Regulatory Information

FCC Information

FCC compliance: This equipment has been

tested and found to comply with the limits for a

digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated in

a commercial environment. This equipment

generates, uses, and can radiate radio

frequency energy and, if not installed and used

in accordance with the instruction manual, may

cause harmful interference to radio

communications. Operation of this equipment in

a residential area is likely to cause harmful

interference in which case the user will be

required to correct the interference at his own

expense.

FCC Conditions

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful

interference.

2. This device must accept any interference

received, including interference that may

cause undesired operation.

EU Conformity Statement

2006/66/EC (battery directive):

This product contains a battery

that cannot be disposed of as

unsorted municipal waste in the

European Union.

See the product documentation for specific

battery information. The battery is marked with

this symbol, which may include lettering to

indicate cadmium (Cd), lead (Pb), or mercury (Hg).

For proper recycling, return the battery to your

supplier or to a designated collection point. For

more information see:www.recyclethis.info.

THE PERFORMANCE OR RELIABILITY OF ANY

SECURITY OR SIGNALING RELATED FUNCTIONS

OF THIS PRODUCT.

This camera adopts new generation sensor with

high sensitivity and advanced circuit board design

technology. It possesses the features of high

resolution, low distortion, and low noise, etc. It is

extremely suitable for supervisory system and

image processing system.

The main features are as follows:

Figure 2-1 The Drill Template

UD.6L0201D1454A01

TURBO HD

720P Turret &Bullet Camera

User Manual

This product and - if applicable -

the supplied accessories too are

marked with "CE" and comply

therefore with the applicable harmonized

European standards listed under the Low Voltage

Directive 2006/95/EC, the EMC Directive 2004/

108/EC, the RoHS Directive 2011/65/EU.

upon the purchase of equivalent new equipment,

or dispose of it at designated collection points.

For more information see:www.recyclethis.info.

2012/19/EC (WEEE directive):

Products marked with this symbol

cannot be disposed of as unsorted

municipal waste in the European

Union. For proper recycling, return

this product to your local supplier

1.2.1 Overview of Type I Camera

l Please make sure that the device in the package

is in good condition and all the assembly parts

are included.

l Make sure that all the related equipment is

power-off during the installation.

l Check the specification of the products for the

installation environment.

l Check whether the power supply is matched

with your power output to avoid damage.

l Please make sure the wall is strong enough to

withstand three times the weight of the camera

and the mounting.

l If the wall is the cement wall, you need to insert

expansion screws before you install the camera.

If the wall is the wooden wall, you can use

self-tapping screw to secure the camera.

l If the product does not function properly,

please contact your dealer or the nearest

service center. Do not disassemble the camera

for repair or maintenance by yourself.

2.1 Installation of Type CameraI

l High performance CMOS sensor and high

resolution bring high-quality image;

l Low illumination, 0.01 Lux @ (F1.2, AGC ON),

0 Lux with IR;

l Support IR cut filter with auto switch;

l OSD menu, parameters are configurable;

l Support auto white balance, auto gain control,

electronic shutter control and internal

synchronization;

l Advanced Engineering Design and patent

universal adjustable structure provides

convenient adjustment and high reliability;

lSMART IR mode;

l Unit transmission control;

l Advanced 3-axis design meets different

installation requirements;

l Ingress protection: IP66.

1.Drill the screw holes and the cable hole on the

ceiling according to the supplied drill template.

2 Push the lock button to disassemble the camera

from the mounting base.

3.Fix the mounting base to the ceiling.

Figure 2-2 Release The Lock Screw

Steps:

PUSH

The HD video output mode is set as the default.

You can short the white and black line-end of the

control switch cable or press the dip switch to

switch the mode as CVBS output.

Figure 1-2 Overview of Type CameraII

Figure 1-1 Overview of Type I Camera

1.2.2 Overview of Type Camera

HD Video Cable

CVBS Cable

Switch Cable

Enclosure

Zoom & Focus

Lock ButtonLock Button

Mounting Base

Camera

Powe r Cable

Mounting Base

Sun Shield

Main Body

Lens

IR LED

HD Video Cable

CVBS Cable

Power Cable

Adjusting Sheet

Focus

Zoom

Dip Switch

Menu Button

Figure 3-3 Manual of WB

Figure 3-4 Smart Mode of DAY&NIGHT

Figure 3-5 Video Settings

3.3 DAY & NIGHT

3.4 Video Setting

Move the cursor to the VIDEO SETTING, and press

the menu button to enter the video configuration

interface. As shown in Figure 3-5.

3.5 FUNCTION

Move the cursor to DAY & NIGHT, and select

COLOR B/W SMART, , or as the DAY & NIGHT mode.

3.6 Reset

Reset all the settings to the default.

3.7 Save & Exit

Move the cursor to , and press OK toSAVE & RESET

save the settings and exit the menu.

3 Menu Operation

3.1 AE

Move the cursor to AE, and you can adjust the

image brightness by the , ,BRIGHTNESS AE MODE

AGC SENS-UP, and in this menu.

As shown in Figure 3-2.

Figure 3-1 Main Menu

Figure 3-2 AE

4.Route the cables to the cable hole and connect

the corresponding cables.

5.Secure the camera to the mounting base by

tightening the lock screw.

6.Adjust the camera according to the figure below

to get an optimum angle.

Figure 2-3 3-axis Adjustment

7.Use the screwdriver to adjust the ZOOM screw

and the FOCUS screw until you get the optimum

image.

Figure 2-4 Zoom and Focus Adjustment

2.2 Installation of Type CameraII

Steps:

1. Drill the screws holes on the ceiling according

to the supplied drill template.

Screw Hole

Template

Figure 2-5 The Drill Template

2.Route the corresponding cables.

3.Secure the camera to the ceiling with the self-

tapping Screws.

Figure 2-6 Secure the Camera to the Ceiling

4.Connect the corresponding cables.

5. Loosen the T screw, R screw and P screw

successively and adjust the camera according to

the figure below to get an optimum angle. Tighten

the screw after completing the adjustment.

R Screw

T Screw

P Screw

6.Adjust the Zoom Screw and Focus Screw till you

get the optimum surveillance angle.

Figure 2-7 3-axis Adjustment

Figure 2-8 Zoom and Focus Adjustment

BRIGHTNESS: Set the brightness value from

1 to 10 to darken or brighten the image.

: Set AE mode as GLOBLE AE, andAE MODE

D-WDR.

AGC HIGH MIDDLE LOW: , , and can be set for the

AGC level. Select OFF to disable the AGC.

: Set the SENSE UP value from 0 to 16.SENSE UP

3.2 WB

Move the cursor to WB, and you can set White

Balance mode as and in this menuAUTO MANUAL .

AUTO: white balance is being adjusted

automatically.

: Set the valueMANUAL R GAIN/B GAIN

from 1 to 10. As shown in Figure 3-3.

COLOR: The image is colored in day mode all the

time.

: The image is black & white all the time, andB/W

the IR LED turns on in the low-light conditions.

: Select to turn on/off the INFRARED_LAMPSMART

and to set the Smart IR level from 1to 16.

As shown in Figure 3-4.

SAMRT

1. INFRARED_LAMP OFF

2. SMART IR 0-|--5

3. RETURN 8

: Set the CONTRAST value from 1 to 10.CONTRAST

: Set the edge and detail sharpnessSHARPNESS

value from 1 to 10.

COLOR GAIN: Set the color gain from 1 to 10.

: Set the 3D NR level as , ,3D NR High Middle

and . Select to disable the 3D NR.Low OFF

: Set the mirror mode as , ,MIRROR OFF H

, or .V HV

You can set , , andDETECTION MASKING ZOOM IN

of the camera in this menu.LANGUAGE

FUNCTION

1. DETECTION 8

2. MASKING 8

3. ZOOM IN 50-|--100

4. LANGUAGE ENGLISH

5. RETURN 8

Figure 3-6 Function

DETECTION: Set the motion sensitivity as

, , or . Select an AREA toWEAK LOW MIDDLE HIGH

enter the motion detection AREA menu. As shown

in Figure 3-7.

: Set the status as / . Select a color forAREA OFF ON

area border. Move the joystick up/down and right

/left to set the horizon/vertical size and position.

As shown in Figure 3-8.

MASKING: Select a masking back ground color.

Select an AREA to enter the masking AREA menu.

As shown in figure 3-9.

: Set the status as / . Move the joystickAREA OFF ON

up/down and right/left to set the horizon/vertical

size and position.

As shown in Figure 3-10.

ZOOM IN: The ZOOM IN value can be adjusted from

50 to 100.

LANGUAGE: Chinese and English are selectable.

DETECTION

1. SENSITIVITY HIGHT

2. AREA NO.0 8

3. AREA NO.1 8

4. AREA NO.2 8

5. AREA NO.3 8

6. RETURN 8

AREA

1. STATUS OFF

2. COLOR WHITE

3. HORIZON SIZE 0

4. VERTICAL SIZE 0

5. HORIZON MOVE 0

6. VERTICAL MOVE 0

7. RETURN 8

Figure 3-7 Detection

Figure 3-8 Detection Area

MASKING

1. COLOR WHITE

2. AREA NO.0 8

3. AREA NO.1 8

4. AREA NO.2 8

5. AREA NO.3 8

6. AREA NO. 8

7. AREA NO.5 8

8. AREA NO.6 8

9. AREA NO.7 8

10.RETURN 8

AREA

1. STATUS OFF

2. HORIZON SIZE 0

3. VERTICAL SIZE 0

4. HORIZON MOVE 0

5. VERTICAL MOVE 0

6. RETURN 8

Figure 3-9 Detection Area

Figure 3-10 Detection

1. BRIGHTNESS 1-|--10

2. AE MODE DWDR

3. AGC OFF

4. SENSE UP 0-|---16

5. RETURN 8

MANUAL

1. R GIAN 1-|--10

2. B GAIN 1-|--10

3. RETURN 8

0 ~360

0 ~75

0~360

AE WB DAY

&NIGHT

VIDEO

SETTING FUNCTION RESET

SAVE

&EXIT

BRIGHTNESS

AE MODE

AGC

SENSE UP

AUTO

MANUAL

COLOR

B/W

CONTRAST

SHARPNESS

COLOR

GAIN

3D NR

MIRROR

DETECTION

MASKING

ZOOM IN

LANGUAGE

SMART

VIDEO

STANDARD

MAIN

VIDEO SETTING

1. CONTRAST 1-|--10

2. SHARPNESS 8

3. COLOR GAIN 1-|--10

4. 3D NR OFF

5. MIRROR OFF

6. RETURN 8

A coaxial camera controller (purchase separately)

is required to select the menu and adjust the

camera parameters.

Focus

Zoom

Especificaciones del producto

Marca:	Hikvision
Categoría:	Cámara de vigilancia
Modelo:	DS-2CE16D5T-AVFIT3
Color del producto:	Zwart
Pantalla incorporada:	Ja
Peso.:	2940 g
Ancho:	170 mm
Profundidad:	230 mm
Altura:	185.5 mm
Peso del embalaje:	4360 g
Ancho del embalaje:	300 mm
Empaquetadura en profundidad:	240 mm
Altura del embalaje:	324 mm
Amable:	NAS
Sistema de control de desequilibrio:	Ja
Indicadores LED:	Ja
Interruptor encendido / apagado:	Ja
Frecuencia del procesador:	2 GHz
Familia de procesadores:	Intel® Celeron®
Modelo de procesador:	N5105
Número de núcleos de procesador:	4
Incluye sistema operativo:	ADM
Puerto USB:	Ja
red LAN:	Ja
Cables suministrados:	AC, LAN (RJ-45)
Lector de tarjetas de memoria integrado:	Nee
Número de puertos HDMI:	1
Número de puertos Ethernet LAN (RJ-45):	2
Opción de montaje de bloqueo de cable:	Ja
Tipo de ranura para candado de cable:	Kensington
Certificación:	VCCI, BIS
Memoria interna:	4 GB
Tipo de memoria interna:	DDR4
Versión del sistema operativo:	4.2.2.RI61
Versión HDMI:	2.0b
Certificados de sostenibilidad:	BSMI, C-TICK, CCC, CE, Federal Communications Commission (FCC), KCC, UKCA
LAN Ethernet, velocidades de transferencia de datos:	100,1000,2500 Mbit/s
Algoritmos de seguridad compatibles:	HTTPS, SSH, SSL/TLS
numero de fans:	1 ventilator(en)
Fabricante del procesador:	Intel
Protocolos de red compatibles:	CIFS/SMB, SMB 2.0/3.0, AFP, NFS, FTP (Unicode Supported), TFTP, WebDAV, Rsync, SSH, SFTP, iSCSI/IP-SAN, HTTP, HTTPS, Proxy, SNMP, Syslog
Gestión basada en web:	Ja
Botón de reinicio:	Ja
Adaptación externa:	Ja
Frecuencia turbo máxima del procesador:	2.9 GHz
Cumplimiento de la sostenibilidad:	Ja
Tipo de vivienda:	Desktop
Número de tomas:	1
Capacidad de la unidad de fuente de alimentación (PSU):	90 W
Unidades de almacenamiento instaladas:	Nee
Unidad de almacenamiento instalada:	Nee
Capacidad de la unidad de almacenamiento:	- GB
Capacidad total de almacenamiento instalada:	- TB
Memoria flash:	8192 MB
Memoria de velocidad de reloj:	2933 MHz
Ranuras de memoria:	2
Factor de forma de memoria:	SO-DIMM
Servidor DHCP:	Ja
Plug and Play universal (UPnP):	Ja
Número de puertos USB 3.2 Gen 2 (3.1 Gen 2) Tipo A:	2
Lista de control de acceso (ACL):	Ja
Modo de sueño:	0.88 W
Navegador compatible:	Firefox, Chrome, Safari, Microsoft Edge
Número de tornillos:	32
Tipo de enfriamiento:	Actief
Soporte RAID:	Ja
Clase de dispositivo:	Home & Home Office
Compatibilidad con tramas gigantes:	Ja
Agregación de conexiones:	Ja
Tecnología de cableado Ethernet de cobre:	2500BASE-T
Interfaces de unidad de almacenamiento compatibles:	SATA
Protocolos de gestión:	SNMP
Tipos de incursión:	0, 1,5, 6,10, JBOD
Activación de la LAN:	Ja
Número de unidades de almacenamiento admitidas:	8
Tamaños de unidades de almacenamiento admitidos:	2.5, 3.5, M.2 "
Canal de entrada de vídeo:	4 kanalen
voltaje-de-entrada-de-CA:	100 - 240 V
Consumo de energía (típico):	35 W
Temperatura de funcionamiento (TT):	0 - 40 °C
Humedad relativa de funcionamiento (VV):	5 - 95 procent
Tipo-de-visualización:	LCD
Soporta múltiples idiomas:	Ja
Diámetro del ventilador:	120 mm
Función de copia de seguridad:	Ja
Propiedades de copia de seguridad:	Cloud, iSCSI LUN
Registro del sistema:	Ja
Servidor FTP incorporado:	Ja
Soporte INTELIGENTE:	Ja
Tipos de unidades de almacenamiento compatibles:	HDD & SSD
soporte iSCSI:	Ja
Consumo de electricidad (HDD en espera):	17.3 W
Ubicación de la fuente de alimentación:	Extern
DNS dinámico (DDNS):	Ja
instantánea:	Ja
Migración RAID en línea:	Ja
Expansión RAID en línea:	Ja
Servidor de medios AV UPnP™ integrado:	Ja
RAM máxima admitida:	16 GB
Escanear en busca de bloques dañados:	Ja
Velocidad de datos admitida LAN Ethernet (máx.):	10000 Mbit/s
Número de ranuras M.2 (M y B):	4
Nivel de ruido (fuera de uso):	17.6 dB
Adaptador WLAN compatible:	Ja
Número de cable de alimentación:	1