Hobart HCM61 Manual de Usario

Hobart procesador de alimentos HCM61

Lee a continuación 📖 el manual en español para Hobart HCM61 (8 páginas) en la categoría procesador de alimentos. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/8

701 S. RIDGE AVENUE

TROY, OHIO 45374-0001

937 332-3000

www.hobartcorp.com FORM 34468 (Apr. 2000)OEM PART 10433

HCM61 & HCM62 FOOD PROCESSORS

MODELS

HCM61 ML-134017

HCM62 ML-134018

– 2 –

Installation, Operation, and Care of

HCM61 & HCM62 Food Processors

SAVE THESE INSTRUCTIONS

GENERAL

The model HCM61 and HCM62 Food Processors are used for

chopping meat, fish, fruits, vegetables, nuts, or dry bread, for

mixing various sauces, mayonnaise, or soups, or for blending or

pureeing various products, such as thickening or desserts. Refer

to Capacity Recommendations, page 6.

The HCM61 has a 1.5 HP motor, is provided with 120 Volt cord and

plug, and requires a 20 Amp. electrical service and receptacle. The

machine operates at 1700 rpm with single speed or pulse control.

The HCM62 has a 2.0 HP motor, is provided with 208 - 240 Volt three

phase cord and plug, and requires a 20 Amp. electrical service and

receptacle. The machine operates at 1700 or 3400 rpm with two

speed or pulse control.

INSTALLATION

UNPACKING

Immediately after unpacking the food processor, check for possible shipping damage. If this machine

is found to be damaged after unpacking, save the packaging material and contact the carrier within 15

days of delivery.

Prior to installation, test the electrical service to assure that it agrees with the specifications on the

machine data plate.

Lift or move the machine only by using the two handles on the sides of the base.

LOCATION

Place the food processor on a suitable sturdy worktop or table. There should be adequate space

around the machine for the user to operate the controls and install and remove the bowl and knife.

©HOBART CORPORATION, 2000

Model HCM61 or HCM62

Food Processor

– 3 –

ELECTRICAL CONNECTIONS (Cord Connected Machines)

WARNING: THE ELECTRICAL CORD ON THIS MACHINE IS EQUIPPED WITH A GROUNDING TYPE

PLUG WHICH MUST BE CONNECTED TO A PROPERLY GROUNDED RECEPTACLE. IF THE

RECEPTACLE IS NOT THE PROPER GROUNDING TYPE, CONTACT AN ELECTRICIAN. DO NOT

REMOVE THE GROUNDING PRONG FROM THE PLUG.

Refer to the machine data plate and Electrical Data, below.

CHECK MOTOR ROTATION (Three-Phase Machines Only)

On model HCM62, check the rotation. With all parts in their normal operating positions (pages 4 – 5),

turn the switch to the Pulse position for two seconds and release. The direction of rotation of the knife

should be counterclockwise as viewed from the top.

If the knife rotates clockwise, correct the rotation using the following procedure:

DISCONNECT THE ELECTRICAL POWER SUPPLY. Interchange any two of the incoming power

supply leads in the plug. Reconnect the power supply and turn the switch to the Pulse position to

verify that the knife rotates counterclockwise as viewed from the top.

PRESTART CHECK

With the machine fully assembled (pages 4 – 5), make sure the cutting blades stop within 4 seconds

after the arm is swung back away from the center of the bowl cover.

Make sure the machine cannot be started with the bowl and cover removed but with the arm swung into

position above the center of the drive shaft.

If the machine fails to work properly, contact Service; do not allow the machine to be operated.

ATADLACIRTCELE ATADLACIRTCELE ATADLACIRTCELE ATADLACIRTCELE ATADLACIRTCELE

ledoM ledoM ledoM ledoM ledoM esahP/ztreH/stloV esahP/ztreH/stloV esahP/ztreH/stloV esahP/ztreH/stloV esahP/ztreH/stloV

yticapmAtiucriCmuminiM yticapmAtiucriCmuminiM yticapmAtiucriCmuminiM yticapmAtiucriCmuminiM yticapmAtiucriCmuminiM

eciveDevitcetorPmumixaM eciveDevitcetorPmumixaM eciveDevitcetorPmumixaM eciveDevitcetorPmumixaM eciveDevitcetorPmumixaM

SPMA SPMA SPMA SPMA SPMA

elcatpeceR elcatpeceR elcatpeceR elcatpeceR elcatpeceR gulP gulP gulP gulP gulP

16MCH 1/06/021 02

R02-5

P02-5:gulP

26MCH 3/06/042-802 02

R02-51L

P02-51L:gulP

.noitidetsetal,07APFN,edoClacirtcelElanoitaNehthtiwecnadroccanidelipmoC

Especificaciones del producto

Marca:	Hobart
Categoría:	procesador de alimentos
Modelo:	HCM61
Color del producto:	Zwart
Peso.:	970 g
Ancho:	129 mm
Profundidad:	60 mm
Altura:	183 mm
Amable:	HDD
Número de puertos USB 2.0:	1
versión USB:	3.2 Gen 1 (3.1 Gen 1)
Conecta y reproduce:	Ja
Soporta el sistema operativo Mac:	Mac OS X 10.5 Leopard
Conector USB:	USB Type-B
Capacidad del disco duro:	3000 GB
Velocidad de rotación del disco duro:	- RPM
USB:	Ja
Tamaño del disco duro:	3.5 "
Temperatura de funcionamiento (TT):	5 - 35 °C
Humedad relativa de funcionamiento (VV):	20 - 80 procent
Tamaño del búfer de la unidad de almacenamiento:	- MB
Velocidades de transferencia de datos USB:	480,5000 Mbit/s
Alimentado por autobús:	USB