Honeywell ImageTeam 3875 Manual de Usario

Honeywell Lector de código de barras ImageTeam 3875

Lee a continuación 📖 el manual en español para Honeywell ImageTeam 3875 (224 páginas) en la categoría Lector de código de barras. Esta guía fue útil para 19 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/224

™

System Manual

Cordless Scanning System

SCANTEAM® 2070 Base

IMAGETEAM™ 3870/75 Linear Imager

SCANTEAM® 5770 Laser

Disclaimer

Hand Held Products, Inc. (“Hand Held Products”) reserves the right to make

changes in specifications and other information contained in this document

without prior notice, and the reader should in all cases consult Hand Held

Products to determine whether any such changes have been made. The

information in this publication does not represent a commitment on the part of

Hand Held Products.

Hand Held Products shall not be liable for technical or editorial errors or

omissions contained herein; nor for incidental or consequential damages

resulting from the furnishing, performance, or use of this material.

This document contains proprietary information that is protected by copyright. All

rights are reserved. No part of this document may be photocopied, reproduced,

or translated into another language without the prior written consent of Hand

Held Products.

Web Address: www.handheld.com

Statement of Agency Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

FCC Class B Compliance Statement

This equipment has been tested and found to comply with the limits for a Class

B digital device pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio or television technician for help.

Caution: Any changes or modifications made to this device that are not

expressly approved by Hand Held Products, Inc. may void the user’s authority

to operate the equipment.

Note:

To maintain compliance with FCC Rules and Regulations, cables

connected to this device must be shielded cables, in which the cable

shield wire(s) have been grounded (tied) to the connector shell.

Canadian Notice

This equipment does not exceed the Class B limits for radio noise emissions as

described in the Radio Interference Regulations of the Canadian Department of

Communications.

Le present appareil numerique n’emet pas de bruits radioelectriques depassant

les limites applicables aux appareils numeriques de la classe B prescrites dans

le Reglement sur le brouillage radioelectrique edicte par le ministere des

Communications du Canada.

CDRH Laser Safety Statement - ST5770 Series Only

This product complies with US DHHS 21 CFR J Part 1040.10. This product is a

CLASS II LASER PRODUCT with a maximum output of 1.0 mW at 670

nanometers and continuous wave.

EN 60825-1 Laser Safety Statement - ST5770 Series Only

This product is classified as a CLASS 2 LASER PRODUCT with a maximum

output of 9.0 mW at 670 nanometers per EN 60825-1:1994, Issue 2, June 1997.

R&TTE Directive

The IMAGETEAM 3870, SCANTEAM 5770, and SCANTEAM 2070 are in

conformity with all essential requirements of the R&TTE Directive (1999/5/EC).

This equipment has been assessed to the following standards: ETS 300 328

ETS 300 826 (November, 1997); EN 60950: 1992, Incl Amdt 1-4, 11.

This product is marked with signifying conformity with Class II

product requirements specified in the R&TTE Directive.

The equipment is intended for use throughout the European Community, but its

authorization for use in France is restricted as follows: PAN European

Frequency Range: 2.402 - 2.480 GHz; Restricted Frequency Range for use in

France: 2.448 - 2.480 GHz.

Regulatory and Safety Agency Approvals

Parameter Specification

Electromagnetic Emissions/Immunity

U.S.A. FCC Part 15, Class B - Verified

Canada SOR 88/475, Class B - Verified

Europe EN 55022 (CISPR22) Class B; ETS 300 826

Type Certified; EMC 89/336/EEC; EN55024

Safety

U.S.A. UL Listed, C22.2 No. 950/UL 1950

Canada 3548cUL Listed

Europe TÜV Rheinland GS Licensed, EN 60950 (IEC

950) (Scanner and Base only - not on battery)

Australia conforms to AS/NZS Standard

Mexico (does not apply to IT3875) Certified

RF Approvals

U.S.A. FCC Part 15.249 Certified

Canada RSS 210 Certified

Europe ETS 300 328 Certified

Australia C-TICK

Mexico IT3870 - SCT RCPWEIM01-348,

ST2070 - RCPWESC01-349

0168

The CE mark on the product indicates that the system has been

tested to and conforms with the provisions noted within the 89/336/

EEC Electromagnetic Compatibility Directive and the 73/23/EEC Low

Voltage Directive.

For further information please contact:

Hand Held Products, Inc.

Nijverheidsweg 9

5627 BT Einhoven

The Netherlands

Hand Held Products shall not be liable for use of our product with equipment

(i.e., power supplies, personal computers, etc.) that is not CE marked and does

not comply with the Low Voltage Directive.

C.S.A. Statement

This product must be used with a certified Class 2 Power

supply or be powered by a certified SELV (Safety Extra

Low Voltage) output.

Patents

Please refer to the product packaging for patent information.

Enlarged Views of Regulatory Labels - IT3870

IT3870 Scanner

Left Side View

IT3870 Scanner

Right Side View

Manufactured

Model #

Item #

S / N

REV

Hand Held Products, Inc.

Skaneateles Falls, NY 13153, USA

Made in USA

Complies with (en conformite avec):

FCC PART 15

CANADA ICES-003

See manual

(Reféréz-vous à la documentation)

CISPR 22 CLASS B

Contains TX FCC ID: EHAUL

ISC: RSS/CNR 210

CANADA: 31101021090A

MAY 2000

IMAGETEAM 3870

3870XX-XX

12345

SW 1.6/1.08

Enlarged Views of Regulatory Labels - IT3875

IT3875 Scanner

Left Side View

IT3875 Scanner

Right Side View

Manufactured

Model #

Item #

S / N

REV

Hand Held Products, Inc.

Skaneateles Falls, NY 13153, USA

Made in USA

Complies with (en conformite avec):

FCC PART 15

CANADA ICES-003

See manual

(Reféréz-vous à la documentation)

CISPR 22 CLASS B

Contains TX FCC ID: EHAUL

ISC: RSS/CNR 210

CANADA: 31101021090A

AUGUST 2001

IMAGETEAM 3875

3875XX-XX

12345

SW 1.6/1.08

Enlarged Views of Regulatory Labels - ST5770

ST5770 Scanne

Left Side View

ST5770

Right Side View

Manufactured

Model #

Item #

S / N

REV

Hand Held Products, Inc.

Skaneateles Falls, NY 13153, USA

Made in USA

MAY 2000

IMAGETEAM 3870

3870XX-XX

12345

SW 1.6/1.08

Complies with (en conformite avec):

FCC PART 15

CANADA ICES-003

See manual

(Reféréz-vous à la documentation)

CISPR 22 CLASS B

Contains TX FCC ID: EHAUL

ISC:RSS/CNR 210

Enlarged Views of Regulatory Labels - ST2070

ST2070 Base - Bottom

handheld.com

This device complies with Part 15 of the FCC

Rules and with RSS-210 of Industry Canada. Op-

eration is subjected to the following two conditions:

(1) This device may not cause harmful interfer-

ence, and (2) This device must accept any interfer-

ence received, including interference that can

cause undesired operation.

Canada ICES-003

See Manual (Reféréz-vous à la documentation)

CISPR 22 CLASS B

Contains TX FCC ID: EHAUL

ISC: RSS/CNR 210

CANADA: 31101021090A

MANUFACTURED: August 2001

MODEL # SCANTEAM 2070

S/N#: U-35-00134

ITEM #: 2070-1A

REV: 3.80/1.08

Chapter 1 - Introduction and Installation

Introduction........................................................................... 1-1

Cordless System: Main Components.................................... 1-3

About the Charge Pack ......................................................... 1-4

Charging Your Charge Pack .......................................... 1-5

Discharging the Charge Pack ......................................... 1-6

Setting Up and Connecting the Cordless System ................. 1-8

Keyboard Wedge Interface ............................................ 1-8

RS-232 Interface ............................................................ 1-9

Connecting More Scanners to the System .......................... 1-11

Beeper and LED Sequences and

Meaning – IT3870/IT3875 .............................................. 1-12

Beeper and LED Sequences and Meaning - ST5770 ......... 1-13

ST5770 Scanner Beep Indication................................. 1-13

LED Sequences and Meaning - ST2070 ............................ 1-14

Basic Operation of the Cordless System ............................ 1-14

System Conditions ....................................................... 1-16

Communication Between the Cordless System

and the Host.................................................................. 1-18

Auxiliary Port............................................................... 1-20

Accessories for the Cordless System ................................. 1-22

Chapter 2 - Quick Start & Interface Menu

Introduction........................................................................... 2-1

Plug and Play Selections ...................................................... 2-2

Industrial Interface: IBM PC.......................................... 2-2

Industrial Interface, Aux Port: RS-232 .......................... 2-2

IBM 468X/9X Ports 5B, 9B, and 17 Interface............... 2-2

Industrial Interface, Aux Port: Wand Emulation

Black High ..................................................................... 2-3

Industrial Interface, Aux Port: Wand Emulation

White High..................................................................... 2-4

Non Decoded Laser Emulation (HHLC)........................ 2-4

Table of Contents

iii

Host Commands (IT3875XXX-X2-1 and ST2070-5 only) 3-15

Data Character Selection .............................................. 3-17

Aux Prefix/Suffix Selections .............................................. 3-18

Decimal to Hex to ASCII Conversion Chart................ 3-20

Aux Prefix Selection .................................................... 3-21

Aux Suffix Selection .................................................... 3-21

Exit Selection for Aux Prefix / Suffix .......................... 3-21

Aux Prefix On/Off........................................................ 3-22

Aux Suffix On/Off........................................................ 3-22

Aux Port I.D. Transmit Selection................................. 3-22

Aux Format Editor Commands .................................... 3-25

Aux Data Format Editor ............................................... 3-27

Aux Data Formatter...................................................... 3-28

Alternate Aux Data Formats......................................... 3-28

Chapter 4 - IMAGETEAM 3875 Features

Introduction........................................................................... 4-1

IT3875 Keypad ..................................................................... 4-1

Key Shifting (Alpha Characters).................................... 4-1

Enter/Backspace ............................................................. 4-2

Keypad Macros............................................................... 4-2

Arrow Keys .................................................................... 4-2

Scrolling ......................................................................... 4-2

Display .................................................................................. 4-3

Function Key .................................................................. 4-3

System Setup......................................................................... 4-5

Script Menu........................................................................... 4-5

IT3875XXX-X2-0 Script Setup ..................................... 4-6

IT3875XXX-X2-1 Script Setup ..................................... 4-6

Run History Factory Script............................................. 4-6

Run Part Number and Quantity Factory Script .............. 4-7

Product Demo Script ...................................................... 4-8

Back.............................................................................. 4-10

Work Group ........................................................................ 4-10

Scanner ID .......................................................................... 4-11

System Info ......................................................................... 4-11

Chapter 5 - Application Work Group Menu

Introduction........................................................................... 5-1

Application Work Group Selection ..................................... 5-3

ST2070-5........................................................................ 5-4

Remove Scanner Selection............................................. 5-4

Programming Keypad Macro Strings (IT3875 and

ST2070-5 only) ................................................................. 5-5

Initiate Key Macro (IT3875 and ST2070-5 only) .......... 5-6

IT3875 Font Characters Chart ............................................. 5-7

Font Size Preference (IT3875 and ST2070-5 only).............. 5-9

Display Language Preference

(IT3875 and ST2070-5 only) .......................................... 5-10

Beeper Volume Selection............................................. 5-11

Beeper Pitch ................................................................. 5-11

Scanner Voting Selection............................................. 5-12

Laser Marker Beam (ST5770 only) ............................. 5-13

AIM Symbology ID and Modifier Prefix..................... 5-13

Hand Held Products Code ID Prefix............................ 5-14

Symbology Chart................................................................ 5-15

Prefix/Suffix Selections ..................................................... 5-16

Prefix Selections........................................................... 5-18

Suffix Selections .......................................................... 5-18

Exit Selection for Prefix/Suffix.................................... 5-19

Work Group Prefix On/Off .......................................... 5-20

Suffix On/Off ............................................................... 5-21

Decimal to Hex to ASCII Conversion Chart................ 5-22

Data Formatter Selections .................................................. 5-23

Data Format Editor Commands ................................... 5-24

Data Format Editor....................................................... 5-26

Data Formatter ............................................................. 5-27

Require Data Format.................................................... 5-27

Decode Beep Selection ................................................ 5-28

Alternate Data Formats ................................................ 5-28

Chapter 6 - Symbology Menu

Introduction........................................................................... 6-1

Codabar ................................................................................ 6-2

Start/Stop Characters...................................................... 6-2

Codabar Message Length ............................................... 6-3

Codabar Check Character............................................... 6-4

Concatenation................................................................. 6-4

Code 39 ................................................................................ 6-6

Start/Stop Characters...................................................... 6-6

Code 39 Message Length ............................................... 6-7

Check Character ............................................................. 6-8

Full ASCII ...................................................................... 6-9

Code 39 Append........................................................... 6-10

Code 93 .............................................................................. 6-11

Code 93 Message Length ............................................. 6-12

Interleaved 2 of 5 ............................................................... 6-13

Interleaved 2 of 5 Message Length .............................. 6-14

Check Digit................................................................... 6-15

Code 2 of 5 ......................................................................... 6-16

Code 2 of 5 Message Length........................................ 6-17

Matrix 2 of 5 ...................................................................... 6-18

Matrix 2 of 5 Message Length ..................................... 6-19

Code 11 .............................................................................. 6-20

Code 11 Check Digits Required................................... 6-20

Code 11 Message Length ............................................. 6-21

Code 128 ............................................................................ 6-22

Code 128 Message Length ........................................... 6-23

<GS> Substitution ........................................................ 6-24

ISBT 128 ...................................................................... 6-24

Telepen ............................................................................... 6-25

Telepen Message Length.............................................. 6-26

Telepen Output ............................................................. 6-26

China Post Code (IT3870/IT3875 only) ............................ 6-27

China Post Code Message Length................................ 6-28

RSS Expanded Message Length................................... 6-30

PDF417 (IT3870PDF/IT3875PDF only) ........................... 6-31

PDF417 Message Length ............................................. 6-32

Macro PDF417 ............................................................. 6-34

Show Macro Control Blocks........................................ 6-34

Scan Diagnostics .......................................................... 6-35

PDF417 Learn Mode.................................................... 6-35

MicroPDF417 (IT3870PDF/IT3875PDF only) ................. 6-36

MicroPDF417 Message Length ................................... 6-37

EAN•UCC Composite Symbology (IT3870PDF/IT3875PDF

only) ................................................................................ 6-38

EAN•UCC Composite ........................................................ 6-38

Enable UPC/EAN Version ................................................. 6-38

EAN•UCC Composite Symbology Message Length... 6-39

EAN/JAN 8 ........................................................................ 6-40

EAN/JAN 13 ...................................................................... 6-41

EAN/JAN 13 ................................................................ 6-41

EAN/JAN Check Digit................................................. 6-41

ISBN............................................................................. 6-41

UPC A ................................................................................ 6-42

UPC A Check Digit...................................................... 6-43

Number System............................................................ 6-43

UPC E0 .............................................................................. 6-44

UPC E0 Check Digit .................................................... 6-44

Number System............................................................ 6-44

Version E Expand ........................................................ 6-45

UPC E1 ............................................................................... 6-45

EAN/UPC Addenda .......................................................... 6-46

EAN Addenda ............................................................. 6-46

UPC Addenda............................................................... 6-47

Chapter 7 - PC Software Tools

Visual Menu.......................................................................... 7-1

Temporary Visual Menu Configuration......................... 7-1

Installing Visual Menu 2003 from the Web................... 7-2

IQ App Loader (IT3875XXX-X2-1 and ST2070-5 only) .... 7-2

Installing the IQ App Loader Demo from the Web ....... 7-2

vii

IQ App Designer (IT3875XXX-X2-1 and ST2070-5 only) . 7-3

IQ Editing Pro™............................................................. 7-3

Chapter 8 - Supported Interface Keys

Keyboard Function Relationships......................................... 8-1

Supported Interface Keys ..................................................... 8-3

Chapter 9 - Product Specifications

SCANTEAM 2070 Cordless Base Product Specifications... 9-1

Radio Specifications ............................................................ 9-2

IMAGETEAM 3870 Cordless Linear Imager Scanner Product

Specifications .................................................................... 9-3

IMAGETEAM 3875 Cordless Linear Imager Scanner Product

Specifications .................................................................... 9-4

SCANTEAM 5770 Cordless Laser Scanner Product Specifica-

tions ................................................................................... 9-5

Charge Pack Specifications (CLESS/NIMH/S) ................... 9-6

Connectors & Pinouts ........................................................... 9-7

Auxiliary RS-232/Wand Emulation Connector ............. 9-8

Keyboard/Terminal and RS-232 (Host Port) Connector 9-9

External Power Connector............................................ 9-10

Cordless Base Dimensions - ST2070.................................. 9-11

Cordless Scanner Dimensions - IT3870 ............................ 9-12

Cordless Scanner Dimensions - IT3875 ............................ 9-13

Cordless Scanner Dimensions - ST5770 ............................ 9-14

Chapter 10 - Maintenance and Troubleshooting

Maintenance........................................................................ 10-1

Cleaning the Scan Window of the Cordless Scanner ... 10-1

Examining the Cordless Scanner and Cordless

Base Housings .............................................................. 10-1

Care and Handling of the Charge Pack ........................ 10-2

Replacing the Interface Cable ...................................... 10-2

Recharging and Replacing the Cordless Scanner’s

viii

Charge Pack ................................................................. 10-2

To Reset Factory Settings ............................................ 10-2

Troubleshooting ................................................................. 10-3

Chapter 11 - Customer Support

Product Service and Repair ................................................ 11-1

Online Product Service and Repair Assistance............ 11-2

Technical Assistance .......................................................... 11-2

Online Technical Assistance ........................................ 11-2

Limited Warranty................................................................ 11-3

Chapter 12 - Default Chart

Country Code Selections.............................................. 12-1

Keyboard & Delays Selection...................................... 12-1

Wand Emulation Selections ......................................... 12-1

Power Settings.............................................................. 12-1

Host Port Communications .......................................... 12-1

Auxiliary Port Communications .................................. 12-2

Output Selections (User Feedback).............................. 12-3

Prefix/Suffix Selections ............................................... 12-3

Data Formatter Selections ............................................ 12-3

Codabar Selections....................................................... 12-3

Code 39 Selection ........................................................ 12-4

Code 93 Selection ........................................................ 12-4

Interleaved 2 of 5 Selection.......................................... 12-4

Code 2 of 5 Selection ................................................... 12-4

Matrix 2 of 5 Selection................................................. 12-4

Code 11 Selection ........................................................ 12-5

Code 128 Selection ...................................................... 12-5

Telepen Selection ......................................................... 12-5

China Post Code Selection (IT3870/IT3875 only)....... 12-5

RSS-14 Selection (IT3870/IT3875 only) ..................... 12-5

PDF417 Selection (IT3870PDF/IT3875PDF only) .... 12-5

MicroPDF417 Selection (IT3870PDF/IT3875PDF only)...

...................................................................................... 12-6

EAN•UCC Composite Symbology Selection (IT3870PDF/

IT3875PDF only) ......................................................... 12-6

EAN / JAN 8 Selection ................................................ 12-6

EAN / JAN 13 Selection .............................................. 12-6

UPC A Selection .......................................................... 12-6

UPC E0 Selection......................................................... 12-7

UPC E1 Selection......................................................... 12-7

EAN/UPC Addenda Selection...................................... 12-7

Cordless Scanning System System Manual 1 - 1

Introduction and Installation

Introduction

The cordless scanning system consists of the SCANTEAM 2070 Base unit and

at least one IMAGETEAM 3870 Cordless Linear Imager, IMAGETEAM 3875

Cordless Linear Imager, or SCANTEAM 5770 Cordless Laser Scanner. Up to

nine IT3870/IT3875 or ST5770 scanners may be associated with one base.

Each cordless scanner has a removable, rechargeable charge pack and

provides real time decoding within 100 feet (30 m) radius of the base unit

depending on the environment.

The IT3875 is intended to serve cordless applications that require enhanced

user/host interaction. The addition of the 16-key keypad and 97 x 32 pixel

graphic (16 character by 4 lines of text) LCD backlit display enables the user to

enter data and view confirmation of receipt of data. The IT3875 linear imagers

ship with two installed factory scripts and a product demo. These scripts keep

track of scan history or part number and quantity.

Two PC tools also are available to help generate custom applications: IQ App

Loader™ and IQ App Designer™. IQ App Loader is used to compile and load

custom script applications created with a text editor. IQ App Designer, an

optional PC software tool, automates the creation of scripts and the task of

loading a user script application to the system. Using IQ App Designer you may

build custom script applications with minimal programming experience.

The cordless system is an economical, durable solution for a wide variety of

portable data collection applications. The cordless system features:

• a tough, ergonomic thermoplastic housing for comfort and durability.

• an advanced two-way spread-spectrum radio

• recognition and decoding of the most popular, industry-standard bar code

symbologies, including PDF417.

• coverage of up to 31,416 square feet (2,919 square meters) around the base.

• a wide range of interfaces that are compatible with many POS, keyboard

wedge, wand and laser emulation, RS-232 terminals, and legacy decoders.

• visible and audible feedback for confirmation of a successful decode.

• a rechargeable charge pack designed to operate through a whole work day.

This manual contains information to help you set up, operate, and program the

cordless system. Product specifications, connector pinouts, scan maps, a

troubleshooting guide, and customer information are also provided.

The cordless system can be programmed for many communications parameters

and input/output protocols compatible to the host, as well as advanced data

editing and formatting. Programming is accomplished by using the single

programming bar codes in this manual.

This section contains the following information:

• Cordless System Main Components

• Charge Pack and Charging Information

• Cordless System Set Up and Connection

• Beeper and LED Sequences and Meaning

1 - 2 Cordless Scanning System System Manual

• Basic Operation of the Cordless System

• Communication Between the Cordless System and the Host

• Accessories for the Cordless System

Cordless Scanning System System Manual 1 - 3

Cordless System: Main Components

Indicator LED

Scan

Window

Trigger

Charge Pack

Charge

Pack Clip

(2 places)

Cordless Scanner

Left Side View

(with charge pack)

Antenna

Keyboard/Terminal

and RS-232 Connector

(Host Port)

External Power

Connector

Aux RS-232, Service Port,

and Wand Emulation

Output Connector

Cordless Base

Back View

1 - 4 Cordless Scanning System System Manual

About the Charge Pack

(CLESS/NIMH/S)

Power is supplied to the cordless scanner by a

rechargeable charge pack that snaps onto the

bottom of the scanner. Each scanner is shipped

with a charge pack.

(See “Charge Pack

Specifications (CLESS/NIMH/S)” on page 9-6 for

technical specifications.)

Note: Order backup charge pack(s) or

replacements from your distributor.

North American Charging Information

The charge pack is designed to plug into any two-

prong North American AC power outlet for direct

charging. You need no additional equipment and you can recharge the pack

virtually anywhere.

Worldwide Charging Information

Since the charge pack is rated for both 120/240 V, 50/60Hz applications, it may

be charged worldwide. Inexpensive snap-on adapters and custom 2-bay and 6-

bay charge strips are available to accommodate a wide variety of electrical

outlets internationally.

Charge Pack Recommendations

• Charge packs are shipped uncharged and need to be conditioned for full

capacity and longer life.

• To maintain the maximum charge capacity, charge packs should be allowed

to fully discharge prior to charging. It is recommended that you establish a

process where a charge pack is used until it is fully discharged and fully

charged before its next use.

• Avoid using the charge pack in extreme temperatures.

• Do not disassemble the charge pack. There are no user-serviceable parts in

the charge pack.

• Avoid extended overcharging; do not leave the charge pack charging for more

than two weeks.

Periodically, about every 6 months, repeat the charge pack conditioning.

Cordless Scanning System System Manual 1 - 5

Proper Disposal of the Charge Pack

When the charge pack has reached the end of its useful life,

the charge packs should be disposed of by a qualified recycler

or hazardous materials handler. Do not incinerate the charge

pack or dispose of the charge pack with general waste

materials. Contact Hand Held Products (see page 11-1) for

recycling or disposal information.

Charging Your Charge Pack

(CLESS/NIMH/S)

Charge the charge pack by following the steps below:

1. Detach the charge pack from the bottom of the scanner. (See figure below)

2. Fully charge the charge pack. Plug the

charge pack directly into any common

120 V AC outlet in North America. If

outside North America, use the custom

charge strip or adaptor.

3. The LED on the bottom of the charge

pack blinks red temporarily as part of

the charge initialization sequence.

After initialization, the LED remains

solid red while the charge pack is

charging. The LED shows green when

the charge pack is fully charged and

ready to use.

Recharge Time: 6 hours at any voltage at

20° °C (68 F).

4. After the charge pack is fully charged,

attach it to the cordless scanner by pressing the pack firmly (align the prongs

on the pack with the mating receptacles) in the base of the scanner until the

release buttons click, holding the pack firmly in place. (

When you attach a

charged charge pack to the cordless scanner, you will hear a single beep

5. If you have not set up your Cordless System, turn to “Setting Up and

Connecting the Cordless System” on page 1-8 for instructions.

6. If the scanner wasn’t previously associated to the base, scan the association

bar code on the top of the base. If the scanner was previously associated to

a base, it will automatically re-associate. (The association process takes

about ten seconds.)

When the charge pack needs recharging, the yellow LED on top of the scanner

pulses in short, continuous blinks when the trigger is pulled. If the LED stops

flashing when the temperature lowers or you do not use the charge pack for

some time, you still need to charge the charge pack.

Press Release Buttons (2

Places)

1 - 6 Cordless Scanning System System Manual

Conditioning the Charge Pack

• Charge packs are shipped uncharged and need to be conditioned for full

capacity and longer life.

• Charge the charge pack for 12 hours for the first two times to fully condition

the pack. (Fully discharge in between each initial charge.)

• Fully discharge the charge pack on a periodic basis by leaving the charge

pack attached to the scanner until the scanner no longer operates, about 24

hours. (Make sure all idle modes are disabled for this procedure -- see

“Charge Pack Conservation Mode” on page 2-15).

Discharging the Charge Pack

A full discharge should take less than 10 hours. Full discharge is indicated when

the trigger is pulled and held for at least 10 seconds and the reader does not

illuminate the aiming line or the status LED. Circuitry in the reader prevents an

over-discharge.

IMAGETEAM 3870/SCANTEAM 5770

The charge packs naturally discharge through normal use of the reader.

Alternately, they may be discharged without user interaction by following these

steps:

1. Disassociate the reader from the base unit by scanning the Remove Scan-

ner/Disassociate bar code (found below).

2. Scan the Battery Discharge Mode bar code (found below) to temporarily

disable the scanner’s power-saving features. The scanner does not operate

normally when in this mode. Do not scan a bar code or the scanner will exit

the Battery Discharge Mode.

3. To resume normal operation, detach and replace the charge pack, then

associate with the base unit by scanning the bar code affixed to the base.

Remove Scanner/Disassociate

Battery Discharge Mode

Cordless Scanning System System Manual 1 - 7

IMAGETEAM 3875

You may automatically discharge the IT3875 charge pack by scanning the

following bar code. The scanner remains operational during the discharge;

however the status LED flashes like a “heartbeat.”

IT3875 Charge Pack Discharge

1 - 8 Cordless Scanning System System Manual

Setting Up and Connecting the Cordless System

Install the base and cordless scanner by following the steps shown below:

Important: Make sure the cordless scanner’s charge pack has been fully

charged. See “Charging Your Charge Pack” on page 1-5 for charging

instructions.

Keyboard Wedge Interface

1. Turn off the power to the host system.

2. Connect the interface cable to the base and to the terminal/computer (steps

1-3, shown in the illustration below). Depending on your application, the

interface cable you need may be different than the one shown.

Note: For optimal coverage, place the base and its antenna as far away from

other sources of RF interference, with a clear transmitting path to the

scanner(s).

The base can be mounted on a wall or a ceiling. Try to place the base so

that the antenna is in a vertical (straight up and down) position whenever

possible. An extra Base Association Bar Code is provided in case the

base is mounted where the label might be difficult to scan (the Association

process is described on page 1-10).

Terminal

(Host system)

Cordless

Base

Disconnect

(Cable, keyboard, and terminal may vary.)

Keyboard Wedge

Interface Example

Cordless Scanning System System Manual 1 - 9

RS-232 Interface

In an RS-232 configuration, connect your interface cable between the base unit

and the host system (steps 1-3, shown in the illustration below). You also need

to use an external power supply. Contact your distributor for more information

on ordering power supplies or RS-232 cables.

3. Turn on the power to the host system. Verify that the base is on; the green

LED on top of the unit should be on. (The base does not have a beeper.)

Terminal

(Host system)

Cordless

Base

(Cable, keyboard, and terminal may vary.)

Power Supply

RS-232 Interface Example

1 - 10 Cordless Scanning System System Manual

4. Using the cordless scanner, scan the Association Bar Code (the bar code

label on the top of the base) to link that scanner to the base.

Two quick beeps followed by clicking, then a single beep indicates a “good”

association. The scanner is in communication with the base. If the scanner

clicks for 30 seconds and signals an error (triple beep), it has not associated with

the base.

Note: If the charge pack is removed from the scanner and replaced after

association, the scanner automatically reassociates to the base, if the

base has power. In this case, the scanner beeps when a charged charge

pack is installed, then beeps a second time after full association, typically

five to ten seconds later.

Note: A scanner always defaults to work group 0 after scanning a base I.D. bar

code.

5. After your cordless scanner has been associated with its base unit, program

the system to work with your terminal or computer by scanning the Terminal

Setup Codes. Use the Supported Terminal list (page 2-6) to scan your

terminal’s Terminal ID.

With Plug and Play programming, you scan

only

one bar code to program the

cordless system to work with a designated interface, including any required

prefixes and suffixes.

6. To determine if your cordless system is set up correctly, scan one of the

sample bar codes in the back of this manual.

Linear Imager or

Laser Scanner

Cordless Base

Association Bar Code

Cordless Scanning System System Manual 1 - 11

Connecting More Scanners to the System

Up to nine cordless scanners may be associated with one base unit. Add more

cordless scanners to a base unit by following the steps shown below:

1. Make sure the cordless scanner’s charge pack has been fully charged.

2. Scan the Association Bar Code (the bar code label on the top of the base) to

link each scanner to the base.

The base stores a unique I.D. for each scanner (up to nine) to identify the

scanner during data communication. Two beeps followed by clicking, then a

single beep from the scanner indicates a “good” association. The base rejects a

tenth cordless scanner trying to link to its network, sending the scanner an error

command. (A rejected scanner beeps three times, indicating an unsuccessful

association.)

Note: When you associate more scanners with the base, you don’t have to

program your cordless system to communicate with your terminal or

computer if you’ve already completed step 5 on page 1-10.

1 - 12 Cordless Scanning System System Manual

Beeper and LED Sequences and

Meaning – IT3870/IT3875

The base contains a green LED that indicates the status of the unit and verifies

its communication with the host system. The IT3870/IT3875 contains an LED on

the top of the unit to indicate its power up, communication, and charge pack

status. Simply stated, red LED = error; green LED = success of any sort; yellow

LED = device is working or busy. The unit’s audible indicators have meaning as

well -- 3 beeps = error; 2 beeps = menu change; 1 beep = all other successes;

clicking/ticking = progress; steady humming = PDF417 decoding

The table below lists the indication and cause of the LED illumination and beeps

for the IT3870/IT3875.

LED Indication Beeper Indication Cause

Normal Operation

Steady Yellow (IT3870) None Working/busy

Yellow - blinking None Battery low

Steady yellow Clicking Indicates an association

attempt

Steady yellow Ticking/humming

Indicates PDF417 or

MicroPDF417 decoding in

process

Steady green 1 beep Successful communication

or association

Red, blinking 3 beeps Failed communication or

association

Menu Operation

Steady green Two beeps (high pitch,

medium pitch Successful menu change

Steady green Two beeps (high pitch,

medium pitch)

Successful intermediate

menu operation

Red, blinking 3 beeps (all 3 high

pitches) Unsuccessful menu change

Cordless Scanning System System Manual 1 - 13

Beeper and LED Sequences and Meaning - ST5770

The ST5770 contains a beeper and two LEDs on the top of the unit (green and

yellow) to indicate its power up, communication, and charge pack status. The

tables below list the indication and meaning of the beeps and LED illumination

scanner.

ST5770 Scanner LED Indication

ST5770 Scanner Beep Indication

Sequence Meaning

Green LED on Trigger pulled, out of range

Green LED on, 2 seconds Successful decode and communication

Green LED blinks, 2 seconds Successful decode with unsuccessful communication, or

unsuccessful clear to scanner

Green LED on, 2 seconds Enter/exit programming mode, successful parameter

change in programming mode

Green LED blinks, 2 seconds Unsuccessful parameter change in programming mode

Yellow LED on Scanning, trigger pulled (in or out of range)

Yellow LED blinks Low battery (trigger pulled)

Sequence Meaning

No beep No scanning, scanning, or low battery (trigger pulled)

1 beep Successful decode and communication

Clicking, then1 beep Successful reassociation

Clicking only Unsuccessful reassociation

2 beeps, clicks, then1 beep Successful association to base

3 beeps - same pitch Unsuccessful association to base (10th scanner), out of

range, or no network.

3 beeps - 2 high and 1 low

pitch

Enter/exit programming mode or successful association to

base. Successful or unsuccessful parameter change in pro-

gramming mode.

4 beeps - low, high, low,

high pitch

Communication error: Successful decode with possible

unsuccessful communication to base. Check host to deter-

mine if data arrived properly.

1 - 14 Cordless Scanning System System Manual

LED Sequences and Meaning - ST2070

The base contains a green LED that indicates the status of the unit and verifies

its communication with the host system.

ST2070 Base LED Indication

Basic Operation of the Cordless System

The following system block diagrams illustrate the basic operating components

of the cordless system.

Cordless Base

The cordless base provides the link between the cordless scanner and the host

system. The base contains a control/interface assembly and an RF

communication module. The RF communication module performs the data

exchange between the cordless scanner and the control/interface assembly.

The control assembly coordinates the central interface activities including:

transmitting/receiving commands and data to/from the host system, performing

software activities (parameter menuing, visual indicator support, power-on

diagnostics), and data translation required for the host system.

Sequence Meaning

LED on continuously Power on, system idle

LED blinks, long duration Power on, diagnostic error

LED blinks, short duration Receiving data from scanner, host, or aux port

LED blinks, four long pulses Communication error detected

RF Module

International

Antenna

Control/Interface Assembly

(Base Circuit Board)

Control

User I/O

Host I/O

LED

I/O Ports

Power

Menu I/O

Multipoint

Host

Aux

Base

Housing

Cordless Base

Cordless Scanning System System Manual 1 - 15

RF (Radio Frequency) Module Operation

The cordless system uses a state-of-the-art two-way 2.4 GHz frequency-hopping

spread spectrum radio to transmit and receive data between the scanner and the

base. Designed for point-to-point and multipoint-to-single point applications, the

radio transmits data at a rate of 1 megabit per second (Mbps). The radio

operates using a license free ISM band, which sends relatively small data

packets at a fast data rate over a radio signal with randomly changing

frequencies, makes the cordless system highly responsive to a wide variety of

data collection applications and resistant to noisy RF environments.

The RF radio used in the cordless system has been tested and approved as

complying with the two leading standards-setting organizations that serve as

regulatory models for compliance in most countries. In North America, the radio

is approved under the standards in FCC B Part 15.249 regulations and, in

Europe, under the standards in ETS 300 328 regulations.

Cordless Scanner

The cordless scanner enables fast and accurate bar code scanning using a non-

contact linear imager or laser input engine. The scanner maintains radio

communication with the base unit up to 100 feet (30m) depending on the

environment.

The scanner is comprised of a linear imager or laser scan engine, a decode/

control assembly, and an RF communication module. The scan engine performs

the bar code image illumination and sensing. The decode/control assembly

coordinates the central communication activities including: capturing and

decoding the bar code image data, performing software activities (parameter

menuing, visual indicator support, low battery indication), and data translation

required for the host system. The RF communication module performs the data

exchange between the scanner and the base.

1 - 16 Cordless Scanning System System Manual

System Conditions

The components of the cordless system interact in specific ways as you

associate one or more scanners to a base, as you move a scanner out of range,

bring a scanner back in range, replace a scanner charge pack, or swap scanners

between two cordless systems. The following information explains the cordless

system operating conditions.

Association Process

After you scan the association label, the base synchronizes radio parameters

and the work group parameter table in the scanner. The work group table is

uploaded during the clicking sequence. Two beeps, clicking, then a single beep

indicates the process is complete. The base blinks while it is sending the table

to the scanner. Until the table is uploaded, scanning and data transmission is

interrupted. If the base is off or not working properly, the scanner emits an error

(triple) beep after trying for 30 seconds to associate to the base.

The work group table is also uploaded any time the base believes a previously

associated scanner wishes to join the network. A scanner always tries to join the

last base it was associated to, even if the scanner has been without power for

several days. The base allows a scanner to associate as long as there are fewer

than nine scanners associated to the base.

Scanner Assembly

Decode/Control Assembly

Control

Trig/Decode

RF Port

Menu I/O

Power Mgmt

Cordless Scanner

Engine

Assembly

Beeper

Antenna

Engine Hsg

Window/Lt Pipe

Trigger

Handle

Housing

(Handle Board)

HHLC I/O

Beeper Port

Module

Download Port

Charge Port

Engine Port

Scan Engine

(Linear Imager

or Laser

Charge Pack

Cordless Scanning System System Manual 1 - 17

Note: A scanner always defaults to work group 0 after scanning a base I.D. bar

code.

Scanner is Out of Range

The cordless scanner is always in communication with its base, even when it is

not transmitting bar code data. Whenever the scanner can’t communicate with

the base for a three second interval, it is out of range. If the trigger is pulled while

the scanner is out of range, the red LED illuminates on the IT3870/IT3875 and

the green and yellow LEDs illuminate on the ST5770. When you scan a bar

code, the scanner issues 3 beeps and does not try to send data to the base.

Note: While the scanner is out of range, it consumes more power searching for

the base continuously. To conserve battery power, store the scanner with

the charge pack removed, or program it for Charge Pack Conservation

mode (see page 2-15).

Scanner is Moved Back Into Range

The scanner silently rejoins (no beep after connecting and synchronizing with the

base) if the scanner has not been reset (charge pack disconnected and

reconnected), no menu codes have been scanned by other scanners in the work

group, and the base has not been reset (see Base Reset Conditions, next page).

Any one of these three conditions can cause the scanner to go through a

reassociation process (definition on page 1-18) when it is moved back in range.

If the scanner reassociates, you will hear a single beep when the reassociation

process (uploading of the parameter table) is complete.

If you believe you are in range and are still hearing a triple (error) beep, you may

have been removed from the base’s network. This could happen if the scanner

loses power or goes out of range for three seconds. Try scanning the association

label or reset the scanner by removing and reinserting the charge pack.

Replacing Charge Pack While Associated

When you insert the charge pack, the scanner beeps, followed by clicking.

During this period the work group parameter table is uploaded to the scanner

from the base. Scanning and data transmission is interrupted. When the

scanner emits a second beep, you may scan again. If you don’t receive a second

beep, the table was not transferred successfully either because the scanner was

out of range or all of the data was not received. Scan the association label again.

Moving Scanners From One Base to Another

You may transfer a scanner from one base to another simply by scanning a new

base association label. A scanner can only be associated to one base at a time.

Once a scanner has been associated to a base, it tries to stay associated to that

base until a new base association label has been scanned. The new base adds

a scanner to its association list as long as fewer than nine scanners are in its

network. If a base has nine scanners in its network, you need to disassociate

one scanner before adding another (see next section).

1 - 18 Cordless Scanning System System Manual

Swapping Scanners Between Two Systems with Nine Scanners on

Each

You may use the Remove Scanner Selection (page 5-4) to disassociate any

scanner. Add a new scanner by scanning the association label with the new

scanner. If you cannot scan the disassociation label because the scanner you

are trying to disassociate was damaged, remove power from that scanner and it

automatically disassociates in approximately three seconds.

Glossary

Rejoin

Rejoin is when the scanner goes out of range and then comes back in range.

The scanner silently rejoins (no beep after connecting and synchronizing with the

base) if the scanner has not been reset (charge pack disconnected and

reconnected), no menu codes have been scanned by other scanners in the work

group, and the base has not been reset.

Base Reset Conditions

The base resets when base power is lost or when a diagnostic problem is

sensed. In either case, the scanners automatically reassociate if they are within

range.

Reassociation

The process of uploading the work group parameter table from the base is called

“reassociation.” During reassociation, the scanner clicks, then beeps once.

Reassociation is done automatically, without having to scan an association label.

Association List

The base keeps an association list of up to nine entries. This list maintains the

associated scanners’ radio serial numbers and dynamic addresses. New

dynamic addresses are assigned to the scanners each time a base reset occurs.

This helps the cordless system track the status of the different scanners in its

network during the association and reassociation process.

Communication Between the Cordless System

and the Host

The cordless scanner provides immediate feedback in the form of a “good read”

indication (a green LED on the scanner and an audible beep) after a bar code is

scanned correctly and the base has acknowledged receiving the data. This is

possible since the cordless system provides two-way communication between

the scanner and the base.

Cordless Scanning System System Manual 1 - 19

When data is scanned, the data is sent to the host system via the base unit.

Confirmation from the host system or the base indicates that the data sent was

received by the host. The cordless scanner recognizes two forms of host

confirmation: data acknowledgement (ACK) from the base unit or an “ACK” from

the host system. If it cannot be determined that the data has been properly sent

to the host system, the scanner issues an error indication. You must then check

to see if the scanned data was received by the host system.

Acknowledgement from the Base

If the cordless system is configured for a keyboard wedge host interface, a signal

(ACK) is sent from the base confirming that the data was received and is being

sent on to the host system. (Since keyboard wedge interfaces cannot provide

bi-directional communications, they do not permit host confirmation.)

3) Base sends

data to host after

ACK is sent to

scanner

1) Good Read

2) A

CK from base

1 - 20 Cordless Scanning System System Manual

Acknowledgement from the Host

Host system confirmation may be implemented with a bi-directional interface like

RS-232. In this configuration, when the base unit receives the scanned data

from the scanner and forwards it to the host, the cordless system waits for a

signal from the host that it received the data. (For information on enabling this

feature and using Host Escape commands, see “Host ACK Selection” on page

3-6).

Auxiliary Port

The Auxiliary (Aux) Port of the ST2070 is a bi-directional RS-232 port. When the

Aux Port is configured as the interface (either using the Plug and Play RS-232

code or terminal ID = 000), the Aux Port is set up to be an RS-232 output port.

For all other interfaces, the Aux Port is available as an RS-232 input port.

Peripheral devices can send data into the Aux Port, and the data is automatically

sent out the main port to the host system.

Note: The Auxiliary Port cannot be used as an input when the base is configured

for the following interfaces: Non-Decoded Laser Emulation (HHLC),

wand emulation, and terminal ID = 000 (Aux Port RS-232 output).

Aux Port as an RS-232 Output Port

When the auxiliary port is configured as an output port, use the Auxiliary Port

Protocol section (page 3-11 - page 3-13) to configure baud rate, parity, data bits,

stop bits, and flow control. To change outgoing data prefix/suffixes, set up data

formatting, and change symbology selections, use the programming selections

in Chapter 5.

1) Good Read

4) ACK from

ho st

(via base)

3) ACK

2) Data to host

Cordless Scanning System System Manual 1 - 21

Aux Port as an RS-232 Input Port

When the auxiliary port is configured as an input port, incoming messages can

be passed on to the host system “as is” or they can be manipulated by the base

prior to sending to the host system. This manipulation may include attaching

prefixes/suffixes to the message and/or data formatting the message.

In order for the base unit to correctly receive a message into the Aux Port, it is

recommended that the incoming message be “framed” by known start and stop

characters. These characters are attached to the message by the input

peripheral, and the base is then programmed to look for these characters. The

base unit is then able to recognize the beginning and end of a message,

eliminating the possibility of partial messages being sent to the host system. Use

the Data Character Selection bar codes (page 3-17) to program these “framing”

characters.

The Auxiliary Protocol section (page 3-11 - page 3-13) is used to configure baud

rate, parity, data bits, stop bits and flow control to match the peripheral protocol

settings.

1 - 22 Cordless Scanning System System Manual

Accessories for the Cordless System

Several accessories are available for the cordless system. Contact your

distributor for more information or to order accessories.

Charge Packs (CLESS/NIMH/S)

The charge pack for the cordless scanner is a rechargeable Nickel Metal Hydride

(NiMH) pack. The unique design of the charge pack it to be directly charged in

a two-prong wall outlet commonly used in North America.

The charge pack may be charged anywhere in the world through a universal

charge strip to physically adapt to the various power plug and socket

configurations.

Each scanner is shipped with one charge pack. Order a back up charge pack or

a replacement charge pack separately.

Charge Strips

To charge more than one charge pack at one time, charge strips are available.

The charge strips are offered in two or six outlet configurations and may be

conveniently wall mounted or placed on flat surfaces. The charge strip uses a

standard PC (IEC 320) grounded power cord between the charge strip and the

electrical AC outlet.

Note: International versions of the power cords are provided by country partners

of Hand Held Products or may be purchased from your local PC supplier.

Hand Held Products does not supply these power cords.

Charge Pack Adapters

Charge pack adapters allow the charge pack to be plugged directly into many

international outlet receptacles. After the charge pack is removed from the

reader, just snap on an adapter and plug it into an outlet. Two models are

available: CLESS/ADAPTEURO for Europlug CEE 7/16 socket types, and

CLESS/ADAPTUK for United Kingdom BS 1363 socket types.

Belt Holster

The belt holster holds the cordless scanner when not in use. The belt holster

consists of a foam covered wire frame clasped to an adjustable nylon web belt

designed to be worn around the waist.

Wall Mount Kit (Standard)

The standard wall mount holder stores the cordless scanner on a vertical surface

for convenient access. The scanner easily slides between two rubberized

fingers that hold the scanner when it is not in use.

Wall Mount Kit (Industrial)

Similar to the standard wall mount holder, the rubberized fingers on the industrial

wall mount holder are smaller to maintain a firm grasp on the scanner under

jolting and jarring conditions, such as those expected in fork lift applications.

Cordless Scanning System System Manual 1 - 23

Head Cover

The head cover features a “D” ring to attach to a tool balancer to suspend the

scanner rather than putting it down.

Base Wall Mount Bracket

For applications where the ST2070 base needs to be firmly mounted to a wall.

The bracket slides into the molded feature on the back side of the base.

Visual Menu

™

Visual Menu is a software configuration tool that provides the ability to configure

the cordless system by connecting the base unit to the COM port of a PC. Visual

Menu allows you to download firmware upgrades, change programmed

parameters, and create and print programming bar codes. Please refer to

Chapter 7 for information about installing Visual Menu from the Hand Held

Products web site.

IQ App Loader

™

(IT3875XXX-X2-1 and ST2070-5 only)

IQ App Loader is a PC tool that takes script applications you create in a text editor

and compiles and loads them into the ST2070-5 base. Please refer to the

VersaCode™ Language Reference User’s Guide for additional information.

IQ App Designer

™

(IT3875XXX-X2-1 and ST2070-5 only)

IQ App Designer is a user friendly PC software tool that automates the

development of custom script applicat experienced script ions. Although an

programmer probably will find greater flexibility in writing scripts using a standard

text editor, this PC tool offers a graphical design environment for rapid

development with minimal programming experience. Please refer to the IQ App

Designer User’s Guide for additional information.

1 - 24 Cordless Scanning System System Manual

Cordless Scanning System System Manual 2 - 1

Quick Start & Interface Menu

Introduction

Use this section to program the cordless system to work with your terminal or

computer (host system).

This programming section contains the following menu selections:

• Plug and Play

• Terminal Interface

• Country Code

• Keyboard

• Output Delays

• Wand Emulation

• Power Settings

• Reset Factory Settings and Status Check

All operating parameters are stored in nonvolatile memory resident in the

cordless system, where they are permanently retained in the event of a power

interruption. When you receive your cordless system, certain operating

parameters have already been set. These are the factory defaults, indicated by

an asterisk (*) on the programming pages (beneath the default programming bar

code). Default Charts that list all the factory settings may be found near the end

of this System Manual.

A Programming Chart (found on the inside back cover of this manual) contains

alphanumeric bar codes for setting additional programming options, such as the

digits representing Symbology Message Length. The chart explains how and

when to use the alphanumeric bar codes.

A Sample Bar Codes pages (located near the back of this manual) provides bar

code symbols you may scan to verify that your cordless system has been

programmed correctly and is communicating with your host system.

2 - 2 Cordless Scanning System System Manual

Plug and Play Selections

Note: Plug and Play menu codes will default all settings before programming the

interface.

Industrial Interface: IBM PC

Note: The bar code above also programs a CR (carriage return) suffix.

Industrial Interface, Aux Port: RS-232

Note: The bar code above also programs the following parameters:

Programmable Option Setting

Baud Rate 38,400 bps

Parity None

Data Format 8 data bits, 1 stop bit

Prefix None

Suffix CR

IBM 468X/9X Ports 5B, 9B, and 17 Interface

Scan one of the following “Plug and Play” codes to program the interface for IBM

4683 Port 5B, 9B, or 17.

Note: When using any of the IBM 4683 interfaces, the maximum allowable data

IBM PC AT and Compatibles Interface

(also PS/2 30-286, 50, 55SX, 60, 70, 70-061, 70-

121, 80)

RS-232 Interface

Cordless Scanning System System Manual 2 - 3

rate into the base aux port is 9600 baud.

Industrial Interface, Aux Port: Wand Emulation

Black High

Note: The two bar codes above also program the following parameters:

Programmable Option Setting

Transmission Rate 25 inches per second

Output Polarity Black High

IBM 468X/9X Port 5B Interface

IBM 468X/9X Port 9B HHBCR-1 Interface

IBM 468X/9X Port 9B HHBCR-2 Interface

IBM 468X/9X Port 17 Interface

Wand Emulation (Code 39 Format) Interface

Wand Emulation (Same Code Format) Interface

Supports Code 39, UPC, EAN, Code 128, Interleaved 2 of 5, and Codabar.

All other codes are output as Code 39.

2 - 4 Cordless Scanning System System Manual

PDF417 Off

Industrial Interface, Aux Port: Wand Emulation

White High

Note: The two bar codes above also program the following parameters:

Programmable Option Setting

Transmission Rate 25 inches per second

Output Polarity White High

PDF417 Off

Note: When in Wand Emulation mode, bar code data containing more than 48

characters may not be sent to the host device.

Non Decoded Laser Emulation (HHLC)

Use HHLC when connecting to a secondary terminal with integral decoding.

Note: The bar code above also programs the following parameters:

Programmable Option Setting

Transmission Rate 37 inches per second

Output Polarity White High

PDF417 Off

Wand Emulation (Code 39 Format) Interface

Wand Emulation (Same Code Format) Interface

Supports Code 39, UPC, EAN, Code 128, Interleaved 2 of 5, and Codabar.

All other codes are output as Code 39.

Non Decoded Laser Emulation

Cordless Scanning System System Manual 2 - 5

Terminal Interface Selections

If your terminal is not one of the Plug and Play options, you must program your

terminal’s interface using one of the “Terminal I.D.” numbers listed in the

following table. To program your terminal to the scanner, scan the Program

Terminal Interface bar code below, then scan the appropriate Terminal I.D. code

and

Save

from the Programming Chart on the inside back cover.

Note: After scanning one of these codes, you must power cycle your computer.

Terminal ID

Save

Cordless Scanning System System Manual 2 - 7

* Emulate External Keyboards and Automatic Direct Connect Mode may also need to

be turned on (see pages 2-9 and 2-11).

** Use Plug and Play Selections on pages 2-3 and 2-4.

Olivetti M19, M24, M28, M200 001

Olivetti M240, M250, M290, M380, P500 003

Relisys TR 175 003

RS-232 Host Port 050

RS-232 Aux Port 000

Serial Wedge 050

Televideo 990, 995, 9060 002

Texas Instruments Extensa 560CD (Portable PC) 003 *

Toshiba 2600 (Portable PC) 003 *

Toshiba Satellite T1960, T2130, CS (Portable

PC) 003 *

Wand Emulation Code 39 output (via Aux Port) **

Wand Emulation Same Code output (via Aux Port) **

WYSE WY-30 013

WYSE WY-85/185 016

WYSE ANSI WY 55, 60, 120, 150, 160, 325, 370,

99GT 015

WYSE ASCII WY 55, 60, 120, 150, 160, 325, 370,

99GT 014

WYSE Enhanced PC WY 55, 60, 120, 150, 160, 370 018

Zenith Z-note (Portable PC) 003 *

Supported Terminals (Continued)

Terminal Model(s) Terminal

I.D.

2 - 8 Cordless Scanning System System Manual

Keyboard and Delays Selections

Keyboard Country

This allows you to re-map the keyboard layout for your selected country. As a

general rule, the following characters are not supported by the cordless system

for countries other than the United States:

@ | $ # { } [ ] = / ‘ \ < > ~

*United States

Belgium

Denmark, Finland,

Norway, Sweden

France

Germany, Austria

United Kingdom

Switzerland

Italy

Cordless Scanning System System Manual 2 - 9

Keyboard Style Selections

Using the Keyboard Style selections, you can program special keyboard

features, such as Caps Lock and Shift Lock.

Regular

is used when you normally have the Caps Lock key off.

Caps Lock

is used when you normally have the Caps Lock key on.

Shift Lock

is used when you normally have the Shift Lock key on (not common

to U.S. keyboards).

Automatic Caps Lock

is used if you change the Caps Lock key on and off. The

software tracks and reflects if you have Caps Lock on or off (AT and PS/2 only).

This selection can only be used with systems that have an LED that notes the

Caps Lock status.

Emulate External Keyboard

should be scanned if you do not have an external

keyboard (IBM AT or equivalent).

*Regular

Caps Lock

Shift Lock

Automatic Caps Lock

Emulate External Keyboard

2 - 10 Cordless Scanning System System Manual

Keyboard Style Modifiers

This allows you to program special keyboard features, such as CTRL+ codes

and Turbo Mode.

Control + ASCII Mode On:

If you scan this selection, the cordless system

sends key combinations for ASCII control characters for values 00-1F. Refer to

page 8-1 for CTRL+ Values.

Turbo Mode:

Selecting Turbo Mode On, (for the IBM AT only), programs the

cordless system to send characters to the terminal faster.

Numeric Keypad Mode:

Selecting Numeric Keypad Mode On sends numeric

characters as if entered from a numeric keypad.

Control + ASCII Mode On

*Control + ASCII Mode Off

Turbo Mode On

*Turbo Mode Off

Numeric Keypad Mode On

*Numeric Keypad Mode Off

Cordless Scanning System System Manual 2 - 11

Automatic Direct Connect: When Emulate External Keyboard has been

selected (page 2-9), Automatic Direct Connect Mode keeps the integrated

keyboard from becoming permanently disabled. (This selection disables the

keyboard for the duration of the bar code transmission.)

Output Delays Selection

This selection provides control of the time delays between data output by the

cordless system to the host terminal. The actual delay is 5 milliseconds

multiplied by the programmed value (00 - 99). Default = 00.

Intercharacter Delay is the time delay between data characters output by the

cordless system to the host terminal.

Interfunction Delay is the time delay between function (key) codes output by the

cordless system to the host terminal.

Intermessage Delay is the time delay between data messages or records output

by the cordless system to the host terminal.

Example: You need a 45 millisecond delay. Scan the Intercharacter Delay bar

code. Scan “0,” “9,” and Save on the Programming Chart (09 x 5ms = 45ms).

1. A two-digit number and Save are required after scanning this programming bar code.

Refer to the Programming Chart (inside back cover).

Automatic Direct Connect Mode On

*Automatic Direct Connect Mode Off

Intercharacter Delay (x5mS) 1

Interfunction Delay (x5mS) 1

Intermessage Delay (x5mS) 1

2 - 12 Cordless Scanning System System Manual

Wand Emulation Selections

Note: When in Wand Emulation mode, bar code data containing more than 48

characters may not be sent to the host device.

Transmission Rate Selection

This programming selection sets the transmission rate from 10 ips (inches per

second) to 300 ips if the cordless system is in Wand Emulation mode.

Programming the transmission rate causes the data to be sent at the specified

rate. The programmed transmission rate must be compatible with the device

receiving the bar code data.

*25

120

150

200

300

Cordless Scanning System System Manual 2 - 13

Output Polarity Selection

This selection allows you to set the output logic convention for the digital output.

The choices are White High and Black High.

White High

*Black High

2 - 14 Cordless Scanning System System Manual

Power Settings

Base Low Power Mode

You may want the base unit to draw less power when it is being powered by a

portable data terminal or laptop. Use Base Low Power mode to tell the base to

draw less power.

Note: Using Base Low Power Mode increases latency in radio communications.

*Off

Cordless Scanning System System Manual 2 - 15

Charge Pack Conservation Mode

The scanner offers three low power modes: 1) No timeout, 2) Don’t check base

network before timeout, and 3) Check base network before timeout.

The lowest standby current is achieved with “No timeout” selected. Radio

contact is maintained and workgroup configuration settings are maintained. “No

timeout” is the default setting and is recommended if the scanner is active for

most of the workday, and the charge pack is removed when the scanner is not in

use.

With Timeout

If “Don’t check base network before timeout” is selected and the scanner is idle.

The timeout period is selectable in increments of 15 minutes up to one hour. On

the next trigger-pull, the scanner begins the reassociation process to restore the

radio link and the workgroup configuration settings. This setting is

recommended if the scanner is left inactive for long periods of time during the

workday or if the charge pack is left attached when the scanner is not in use.

The “Check base network before timeout” mode is identical to the previous mode

except that when the timeout period expires, the scanner tests whether it is still

in radio contact with the base. This setting may be recommended if the charge

pack is left attached and the base is powered off at the end of each working day.

Product Prior to Timeout After Timeout

IT3870/ST5770 20 mA 10 mA

IT3875 25 mA 15 mA

*No Timeout

No Timeout

Product Current

IT3870/ST5770 15 mA

IT3875 20 mA

Don’t Check for Network Base

Before Timeout

Check for Network Base

Before Timeout

2 - 16 Cordless Scanning System System Manual

Timeout Period Selections

Low Power Timeout (IT3875 only)

The IMAGETEAM 3875 enters a sleep mode when low power timeout occurs.

When the scanner goes to sleep, the keypad is temporarily disabled. To wake

the scanner from the sleep mode pull the trigger or press ENTER. Pressing the

ENTER key wakes the system even if the executing script is not accepting

keypad input.

Timeout after 15 minutes

Timeout after 30 minutes

Timeout after 45 minutes

*Timeout after 1 hour

Cordless Scanning System System Manual 2 - 17

Factory Default and Revision Report Selections

Reset Factory Settings

Scanning the Factory Default Settings bar code resets the cordless system to

the original factory settings, clearing any programming changes you may have

made. You may reset the factory default settings for the current application

group or for all application groups.

The Current Application Group Default defaults only the settings described in

Chapter 4 of this manual.

The ALL Application Groups Default sets the terminal ID to 003, then changes all

settings to factory default values. (See Chapter 12 for a listing of all the factory

defaults.)

Revision Report

Scan the Report Base Software Revision bar code to transmit the cordless base

software revision level to the host terminal. The base software revision will be

printed out as “Base software revision: X.XX, Radio: K.KK.” (The “Xs” and “Ks”

will vary according to the firmware revision.)

Scan the Report Scanner Software Revision bar code to transmit the cordless

scanner software revision level to the host terminal.

Scanner software and hardware revision for the IT3875 can be accessed through

the System Info portion of System Setup described on page 4-5.

Factory Default Settings: Current Application Group

Factory Default Settings: ALL Application Groups

Report Base Software Revision

Report Scanner Software Revision

2 - 18 Cordless Scanning System System Manual

Cordless Scanning System System Manual 3 - 1

Communications Menu

Introduction

Use this section to program the communications parameters for the cordless

system.

This programming section contains the following menu selections:

• Host Port Protocol/Communications (RS-232)

• Auxiliary Port Protocol/Communications (RS-232)

Cordless Scanning System System Manual 3 - 3

Host Port Protocol

Parity Selection

This selection provides a means of checking character bit patterns for validity.

The cordless system can be configured to operate under Even, Odd,

Mark,None, or Space parity options. The host terminal must be set up for the

same parity as the cordless system to ensure reliable communication.

Word Length Data Bits Selection

This selection sets the Word Length at seven or eight bits of data per character.

If an application requires only ASCII Hex characters 0 through 7F decimal (text,

digits, and punctuation), select 7 data bits. For applications requiring use of the

full ASCII set, select 8 data bits per character.

*None

Space

Mark

Even

Odd

7 Data Bits

*8 Data Bits

3 - 4 Cordless Scanning System System Manual

Host Port Protocol

Word Length Stop Bits Selection

This selection sets the Word length at one or two stop bits.

*1 Stop Bit

2 Stop Bits

Cordless Scanning System System Manual 3 - 5

Host Port Communications

Hardware Flow Control Selection

This selection turns on hardware flow control that checks for a CTS signal before

sending data. This option is useful when your application supports the CTS

signal.

Note: This selection canno Wedge Output Selection.t be used with Serial

Serial Wedge Output Selection

This selection selects the serial output direction required by your application. P1

and P2 are serial wedge designations printed on the serial wedge cable. Usually,

one goes to the host and one goes to the terminal, depending on your specific

application and the serial wedge cable.

*Off

To P1

To P1 and P2

To P2

*None (Host Port RS-232)

3 - 6 Cordless Scanning System System Manual

Host Port Communications

Host ACK Selection

Some applications require that the host terminal (or server) approve or reject

incoming bar code data and notify the operator of these actions. These

applications require that the host maintain control over the response indicators

emitted from the source scanner. Turning the Host ACK selection on, configures

the cordless system scanners to respond to commands from the host system.

The following criteria must be met for the Host ACK to work correctly:

• The cordless system must be configured for “Host Port RS-232” (Terminal ID

= 050)

• Both the host terminal and the cordless system must have RTS/CTS

handshaking (“Hardware Flow Control Selection” on page 3-5) enabled.

• Host ACK must be enabled (page 3-7).

• System performance degrades when using Host ACK at rates lower than

9600.

• The host terminal software must be capable of interpreting the bar code data,

make decisions based on the data content, and send out appropriate escape

commands to the source scanner.

Escape commands are addressed to the source scanner via “Application Work

Groups.” Once a command is sent, all scanners in a group respond to that

command. Because of this situation, it is recommended that each scanner is

assigned to its own group.

The commands to which the scanner responds are listed on page 3-8 and page

3-9. The <ESC> is a 1B hex. A typical command string is y <ESC> x, where “y”

is the application work group number, “<ESC> x” is the escape command, and

the comma is the terminator.

Up to twenty commands may be strung together to create custom response

sequences. An example of a command is listed below.

0<ESC>4<ESC>5<ESC>6,

The above example will make a scanner in application work group zero beep low,

medium, high.

Once Host ACK is enabled, the system works as follows:

• The scanner reads a code and sends data to the base/host system. No

audible or visual indication is emitted, unless “Decode Beep” is enabled (page

3-10). The scanner read indicator goes out upon a successful read.

• Scanner is suspended until 1) a valid escape string is received from the host

system (via the base) or 2) the scanner “times out.”

• Once condition 1 or 2 above has been met, the scanner is ready to scan again,

and the process repeats.

Time out is indicated by three rapid beeps at the same pitch. A time out occurs

if the source scanner does not receive a valid escape command in 10 seconds.

If a time out occurs, the operator should check the host system to understand

why a response to the scanner was not received.

Cordless Scanning System System Manual 3 - 7

Host Port Communications

Host ACK Enable

*Off

3 - 8 Cordless Scanning System System Manual

Host Port Communications

Escape Commands

The tables below list the escape commands that must be generated from the host

system and the resulting action(s).

ST5770 Escape Commands

Command Action

<ESC> a Beep (two high tones), illuminate green LED for two seconds

<ESC> b Beep (three low tones), illuminate green LED nine times

<ESC> 1 Illuminate green LED for 135 milliseconds

<ESC> 2 Illuminate green LED for two seconds

<ESC> 3 Illuminate green LED for five seconds

<ESC> 4 One beep at low volume

<ESC> 5 One beep at medium volume

<ESC> 6 One beep at high volume

<ESC> 7 Beep (one medium tone), illuminate green LED two seconds

<ESC> 8 Beep (three low tones), illuminate green LED nine times

Cordless Scanning System System Manual 3 - 9

Host Port Communications

IT3870/IT3875 Escape Commands

Command Action

<ESC> a Indicate as if successful menu change made

<ESC> b Indicate as if unsuccessful menu change made

<ESC> 1 Illuminate green LED for 135 milliseconds (followed by at least 70 mSecs.

dark time when multiple blinks)

<ESC> 2 Illuminate green LED for two seconds (followed by at least 500 mSecs.

dark time when multiple blinks)

<ESC> 3 Illuminate green LED for five seconds (followed by at least 500 mSecs.

dark time when multiple blinks)

<ESC> 4 One beep at low volume

<ESC> 5 One beep at medium volume

<ESC> 6 One beep at high volume

<ESC> 7 Indicate as successful decode and communication to host.

<ESC> 8 Indicate as unsuccessful decode and communication to host.

Cordless Scanning System System Manual 3 - 11

Auxiliary Port Protocol

Default Auxiliary Port Protocol

Baud Rate Selection

This selection sets the baud rate from 300 bits per second to 38,400 bits per

second. Programming baud rate causes the data to be sent at the specified rate.

The device connected to the Auxiliary Port must be set up for the same baud rate

as the Aux Port to ensure reliable communication.

300

600

2400

1200

4800

9600

*38400

19200

3 - 12 Cordless Scanning System System Manual

Auxiliary Port Protocol

Parity Selection

This selection provides a means of checking character bit patterns for validity.

The Auxiliary Port can be configured to operate under Even, Odd, Mark, None,

or Space parity options. The device connected to the Auxiliary Port must be set

up for the same parity as the Aux Port to ensure reliable communication.

Word Length Data Bits Selection

This selection sets the Word Length at seven or eight bits of data per character.

If an application requires only ASCII Hex characters 0 through 7F decimal (text,

digits, and punctuation), select 7 data bits. For applications requiring use of the

full ASCII set, select 8 data bits per character.

*None

Space

Mark

Even

Odd

7 Data Bits

*8 Data Bits

Cordless Scanning System System Manual 3 - 13

Auxiliary Port Protocol

Word Length Stop Bits Selection

This selection sets the Word Length at one or two stop bits.

Hardware Flow Control Selection

This selection turns on hardware flow control that checks for a CTS signal before

sending data. This option is useful when your application supports the CTS

signal.

*1 Stop Bits

2 Stop Bits

*Off

Cordless Scanning System System Manual 3 - 15

Auxiliary Port Communications

Host Commands (IT3875XXX-X2-1 and ST2070-5 only)

Most VersaCode script commands can be sent by RS-232 from the host to a

scanner via the base unit. When the host sends the VersaCode commands,

they are called Host Commands. Host Commands can be used to control every

function of the scanner. For example, Host Commands may be used to put a

text prompt on the scanner’s display or to get input from the scanner or keypad.

Host Commands may be used to notify the operator that scanned data has been

accepted or rejected by putting a picture on the scanner’s display or by sounding

the beeper and lighting the LEDs. In this way, they are much like Host ACK

escape commands (“Host ACK Selection” on page 3-6), only Host Commands

are more powerful.

The following criteria must be met for Host Commands to work correctly:

• The cordless system must be configured for Aux Port RS-232 (Terminal ID =

000).

• Both the host terminal and the cordless system must have RTS/CTS

handshaking (“Hardware Flow Control Selection” on page 3-5) enabled.

• Host Commands are addressed to an individual scanner using a four-

character Scanner ID.

• The scanner must be expecting the Host Command. This is accomplished

using one of three VersaCode commands resident in the scanner:

WaitForMultiple Commands, WaitForCommand, or CheckForCommand. For

additional information, please refer to the VersaCode Language Reference

User’s Guide.

• Refer to VersaCode Language Reference User’s Guide to determine which

VersaCode commands are available as Host Commands and for the correct

syntax of the commands.

• The host computer must be capable of sending Host Commands by RS-232

and capable of interpreting the response to each command.

Each scanner responds to only one Host Command at a time. The host receives

a response from the scanner when the command has been processed.

Especificaciones del producto

Marca:	Honeywell
Categoría:	Lector de código de barras
Modelo:	ImageTeam 3875

¿Necesitas ayuda?

Si necesitas ayuda con Honeywell ImageTeam 3875 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

Lector de código de barras Honeywell Manuales

Honeywell 7980G-2USBC-0 Manual de Usario

11 Octubre 2024

Honeywell 7800LWN Manual de Usario

6 Octubre 2024

Honeywell Dolphin 99EX Manual de Usario

3 Octubre 2024

Honeywell ScanPal EDA50K Manual de Usario

13 Septiembre 2024

Honeywell CW45 Manual de Usario

10 Septiembre 2024

Honeywell ScanPal EDA51K Manual de Usario

10 Septiembre 2024

Honeywell CT47 Manual de Usario

9 Septiembre 2024

Honeywell OptimusS SP5500 Manual de Usario

5 Septiembre 2024

Honeywell Captuvo SL22 Enterprise Sled Manual de Usario

1 Septiembre 2024

Honeywell ScanGlove IS4225 Manual de Usario

24 Agosto 2024

Lector de código de barras Manuales

Últimos Lector de código de barras Manuales

Datalogic Magellan 8302 Manual de Usario

27 Octubre 2024

Casio Cassiopeia IT-10 M30BR Manual de Usario

23 Octubre 2024

Intermec CN50 Manual de Usario

20 Octubre 2024

Intermec SR60 Manual de Usario

19 Octubre 2024

Datalogic CBX500 Manual de Usario

9 Octubre 2024

Datalogic QuickScan L QD2300 Manual de Usario

5 Octubre 2024

Renkforce 7A CR6307A Manual de Usario

3 Octubre 2024

Datalogic PowerScan 7000 2D Manual de Usario

23 Septiembre 2024

Datalogic MGL8500X Manual de Usario

23 Septiembre 2024

IFM O2I501 Manual de Usario

22 Septiembre 2024