Hooker 1618-75019-DKW Manual de Usario

Hooker Silla 1618-75019-DKW

Lee a continuación 📖 el manual en español para Hooker 1618-75019-DKW (2 páginas) en la categoría Silla. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

1/2

ASSEMBLY INSTRUCTION

Item#:1618 75019- - DKW Upholstered Dining Bench

** Please make sure you have all prior to assembly.parts indicated below

Assembly Steps:

Please follow numbers on one chair and letters on the other chair during assembly.

1. Place chair back on a clean surface.

2. T ighten back frame s rail to chair back legs (G) and assemble back legs (G) to the corner block of

seat frame(I) by using 4 bolts ( lock washers (E 4 ), C) and 4 flat washers (D).

3. 4 E 4 CAssemble front legs (F) to corner blocks of seat frame (I), using bolts ( ), lock washers ( ) and

4 flat washers (D ).

4. 4 B 4 CScrew front and back (H) on center leg center using rail bolt ( ), lock washer ( ) and 4 flat

washer (D ).

5. Make sure the chair is level and then tighten all bolts completely by using wrench Allen (A).

6. Turn the chair upright. Level the chair following the “chair leveling instruction” as below.

Diagram 1

2/2

PLEASE READ THESE INSTRUCTIONS PRIOR TO ASSEMBLING THE CHAIRS

CHAIR LEVELING INSTRUCTION SUPPLEMENT

Chair leveling procedures:

To make the assembly process easy and efficient, please read the entire instruction sheet prior to

assembling the chair. Make sure all hardware listed is included. To properly assemble the chair, none of

the bolts should be fully tightened until all components are attached to the chair. This will allow an

opportunity to level the chair and prevent any unnecessary “rocking”.

1. Place the loosely assembled chair on a hard flat surface.

2. Apply gentle downward pressure on the seat. This step eliminates rocking and ensures the chair to

be level.

3. Once the chair is level, tighten all bolts and nuts.

Note:

Most floors have slight irregularities that can affect chair leveling. If your chair is uneven when placed

in its desired location, perform the following steps:

1. Loosen front legs to finger tight.

2. Extend both front legs ward to their fullest length.up

3. Gently push downward on the front edge of the seat until all four legs rest on the floor.

4. -Re tighten all bolts and nuts.

Cleaning Instruction: Clean finished parts with a damp cloth using a mild dishwashing liquid and water solution.

Polish the finish with soft cloth and an industry recognized furniture polish.

Especificaciones del producto

Marca:	Hooker
Categoría:	Silla
Modelo:	1618-75019-DKW
Color del producto:	Wit
Peso.:	142 g
Ancho:	62 mm
Profundidad:	137 mm
Altura:	42 mm
Tipo de fuente de energía:	DC
Certificación:	EN 50131-1, EN 50131-2-2, EN 50130-4, EN 50130-5
Tipo de sensor de imagen:	Passieve infraroodsensor (PIR)/Microgolfsensor
Voltaje de entrada:	12 V
El consumo de energía:	97 mA
Temperatura de funcionamiento (TT):	-10 - 55 °C
Humedad relativa de funcionamiento (VV):	0 - 93 procent
Ángulo de detección:	90 °
Distancia de detección:	24 m
Altura de instalación (máx.):	2.4 m
Encendido en espera:	13 mA