Hotpoint CD67G0C2CA/UK Manual de Usario

Hotpoint horno CD67G0C2CA/UK

Lee a continuación 📖 el manual en español para Hotpoint CD67G0C2CA/UK (8 páginas) en la categoría horno. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/8
CD67G0CCX/UK
CD67G0C2CJ/UK
CD67G0C2CA/UK
ADAPTING TO DIFFERENT TYPES OF GAS
(This operation needs to be carried out by a
qualified technician.)
In order to adapt the appliance to a type of gas
other than the type for which it was manufactured
(indicated ontherating label), follow thededicated
steps provided after installation drawings.
ELECTRICAL WARNINGS
IMPORTANT: Information about current and
voltage consumption is provided on the rating
plate.
The rating plate is on the front edge of the
oven (visible when the door is open).
It must be possible to disconnect the appliance
from the power supply by unplugging it if
plug is accessible, or by a multi-pole switch
installed upstream of the socket in accordance
with the wiring rules and the appliance must
be earthed in conformity with national electrical
safety standards.
The power cable must be long enough to connect the appliance,
once fitted in its housing, to the main power supply. Do not pull the
power supply cable.
Do not use extension leads, multiple sockets
or adapters. The electrical components must not
be accessible to the user after installation. Do not
use the appliance when you are wet or barefoot.
Do not operate this appliance if it has a damaged
power cable or plug, if it is not working properly,
or if it has been damaged or dropped.
If the supply cord is damaged, it must
be replaced with an identical one by the
manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard -
risk of electric shock.
If the power cable needs to be replaced,
contact an authorised service centre.
CLEANING AND MAINTENANCE
WARNING: Ensure that the appliance is
switched off and disconnected from the power
supply before performing any maintenance
operation; never use steam cleaning equipment -
risk of electric shock.
Do not use harsh abrasive cleaners or metal
scrapers to clean the door glass since they can
scratch the surface, which may result in shattering
of the glass.
Do not use abrasive or corrosive products,
chlorine-based cleaners or pan scourers.
Make sure the appliance has cooled down
before cleaning or performing maintenance. - risk
of burns.
WARNING: Switch off the appliance before
replacing the lamp - risk of electric shock.
To avoid damaging the electric ignition device, do not use it when
the burners are not in their housing.
Wear protective gloves for cleaning and
maintenance.
DISPOSAL OF PACKAGING MATERIALS
ENERGY SAVING TIPS
Only preheat the oven if specified in the cooking table
dark lacquered or enamelled baking trays as they
to save even more energy and time.
DISPOSAL OF HOUSEHOLD APPLIANCES
This appliance meets: Ecodesign requirements of European
Regulation 66/2014; Energy Labelling Regulation 65/2014;
Products and Energy Information (Amendment) (EU Exit)
Regulations (2019), in compliance with the European standard:
EN 15181. This appliance meets Ecodesign requirements
Energy-Related Products and Energy Information
(Amendment) (EU Exit) Regulations 2019 in compliance
with the European standard EN 30-2-1.
DECLARATION OF CONFORMITY
Ecodesign for Energy-Related
of European Regulation 66/2014 and the Ecodesign for
The packaging material is 100 % recyclable
and is marked with the recycle symbol .
The various parts of the packaging must therefore
be disposed of responsibly and in full compliance
with local authority regulations governing
waste disposal .
This appliance is manufactured with recyclable or
reusable materials. Dispose of it in accordance
with local waste disposal regulations . For further information
contact your local authority, the collection service for household
waste or the store where you purchased the appliance.
This appliance is marked in compliance with
The European Directive 2012/19/EU, Waste Electrical and
Electronic Equipment ( WEEE ) and with the
Waste Electrical and Electronic Equipment regulations 2013
( as amended ) . By ensuring this product is disposed
of correctly , you will help prevent negative consequences
for the environment and human health . The ed , symbol
on the product or on the accompanying documentation
indicates that it should not be treated as domestic
waste but must be taken to an appropriate
collection centre for the recycling of electrical and
electronic equipment.
on the treatment, recovery and recycling of household
household electrical appliances,
or your recipe. Use dark lacquered or enamelled
absorb heat better. Use a pressure cooker
6
V
V
Z
• Pry the fixing tab “V” and remove the oven burner
• Unscrew the oven burner nozzle using the socket
spanner for the nozzles “Z”“Z”
“Z”“Z”“Z”, or a 7 mm socket
spanner, and replace it with a nozzle suited to the
new type of gas (see Table 1).
Take particular care handling the spark plug
wires and the thermocouple pipes.
• Replace all the parts, following the steps
described above in the reverse order.
b )b )
b )b )
b ) Minimum regulation of the main and top gas
oven burner with thermostat:
• light the burner as described in the
paragraph the oven knob” of the
instruction booklet.
• turn the knob to MaxMax
MaxMaxMax for about 10 minutes
and then turn the knob to the MinMin
MinMin
Min
setting;
• remove the knob;
• regulate the screw positioned outside the
thermostat pin until the flame is
small but steady.
! !
! ! In the case of liquid gas, the regulation screw
must be screwed in to the bottom.
• check that the burner does not turn off whenwhen
you turn the knob from Max to Min and and
when you open and close the oven door quickly.
Adapting the gas grill to different types of gas
Replacing the nozzle of the grill burner:
On completion of the operation, replace the old
rating sticker with one indicating the new type of gas
used. This sticker is available from our Service
Centres.
No t eNo t e
No t eNo t eNo t e
Should the pressure of the gas used be different (or
vary) from the recommended pressure, it is
necessary to fit a suitable pressure regulator onto
the inlet pipe in compliance with current National
Regulations relative to “regulators for channelled
gas”.
If the appliance is connected to a liquid gas supply, the
bypass screw must be set to a minimum.
While the burner is alight, quickly change the position of the
knob from minimum to maximum and vice versa several times,
checking that the flame is not extinguished.
Upon completion of adjustment, reseal using sealing
wax or an equivalent material.
1. Remove the enamelled baffle at the front of the grill
(2 screws).
2. Remove the screw on the right hand side of the
burner and gently slide the burner off the injector.
3. Using a 7mm socket, replace the grill injector as
appropriate (see table on previous page).
4. Re-assemble the burner and baffle.
Adapting to different types of gas (main and top
oven)
In order to adapt the oven to a different type of gas
with respect to the gas for which it was
manufactured (indicated on the label), follow these
simple steps:
a)a)a)a)a) Replacing the oven burner nozzle
•open the oven door fully
•pull out the sliding oven bottom
unscrew the two screws and take o the shield
protecting the burner (in main oven burner only).
V
V
Z
• Pry the fixing tab “V” and remove the oven burner
• Unscrew the oven burner nozzle using the socket
spanner for the nozzles “Z”“Z”
“Z”“Z”“Z”, or a 7 mm socket
spanner, and replace it with a nozzle suited to the
new type of gas (see Table 1).
Take particular care handling the spark plug
wires and the thermocouple pipes.
• Replace all the parts, following the steps
described above in the reverse order.
b )b )
b )b )
b ) Minimum regulation of the main and top gas
oven burner with thermostat:
• light the burner as described in the
paragraph the oven knob” of the
instruction booklet.
• turn the knob to MaxMax
MaxMaxMax for about 10 minutes
and then turn the knob to the MinMin
MinMin
Min
setting;
• remove the knob;
• regulate the screw positioned outside the
thermostat pin until the flame is
small but steady.
! !
! ! In the case of liquid gas, the regulation screw
must be screwed in to the bottom.
• check that the burner does not turn off whenwhen
you turn the knob from Max to Min and and
when you open and close the oven door quickly.
Adapting the gas grill to different types of gas
Replacing the nozzle of the grill burner:
On completion of the operation, replace the old
rating sticker with one indicating the new type of gas
used. This sticker is available from our Service
Centres.
No t eNo t e
No t eNo t eNo t e
Should the pressure of the gas used be different (or
vary) from the recommended pressure, it is
necessary to fit a suitable pressure regulator onto
the inlet pipe in compliance with current National
Regulations relative to “regulators for channelled
gas”.
If the appliance is connected to a liquid gas supply, the
bypass screw must be set to a minimum.
While the burner is alight, quickly change the position of the
knob from minimum to maximum and vice versa several times,
checking that the flame is not extinguished.
Upon completion of adjustment, reseal using sealing
wax or an equivalent material.
1. Remove the enamelled baffle at the front of the grill
(2 screws).
2. Remove the screw on the right hand side of the
burner and gently slide the burner off the injector.
3. Using a 7mm socket, replace the grill injector as
appropriate (see table on previous page).
4. Re-assemble the burner and baffle.
Adapting to different types of gas (main and top
oven)
In order to adapt the oven to a different type of gas
with respect to the gas for which it was
manufactured (indicated on the label), follow these
simple steps:
a)a)a)a)a) Replacing the oven burner nozzle
•open the oven door fully
•pull out the sliding oven bottom
unscrew the two screws and take o the shield
protecting the burner (in main oven burner only).
INSTALLATION TIPSINSTALLATION TIPS
EN
WARNING : This operation must be perfomed
by a qualified technician
10

Especificaciones del producto

Marca: Hotpoint
Categoría: horno
Modelo: CD67G0C2CA/UK

¿Necesitas ayuda?

Si necesitas ayuda con Hotpoint CD67G0C2CA/UK haz una pregunta a continuación y otros usuarios te responderán


horno Hotpoint Manuales

Hotpoint

Hotpoint SA2 540 H WH Manual de Usario

17 Octubre 2024
Hotpoint

Hotpoint OS 89 IX Manual de Usario

14 Octubre 2024
Hotpoint

Hotpoint PC 640 X /HA Manual de Usario

8 Octubre 2024
Hotpoint

Hotpoint SI5 851 C IX Manual de Usario

4 Octubre 2024
Hotpoint

Hotpoint G750TX Manual de Usario

4 Octubre 2024
Hotpoint

Hotpoint RBS360DMWW Manual de Usario

4 Octubre 2024
Hotpoint

Hotpoint HD5G00KCB Manual de Usario

3 Octubre 2024
Hotpoint

Hotpoint FID 834 H MR HA Manual de Usario

2 Octubre 2024
Hotpoint

Hotpoint FIT 801 H AN HA Manual de Usario

29 Septiembre 2024
Hotpoint

Hotpoint BS43B Manual de Usario

29 Septiembre 2024

horno Manuales

Últimos horno Manuales

Continental Edison

Continental Edison CECM6065W Manual de Usario

27 Octubre 2024
Taurus

Taurus HM778WHD Manual de Usario

27 Octubre 2024
Lacanche

Lacanche CITEAUX Manual de Usario

27 Octubre 2024
JennAir

JennAir JDS1450FS Manual de Usario

27 Octubre 2024
Orima

Orima ORP-76-IN Manual de Usario

27 Octubre 2024
Breville

Breville the Handy Hot Plate BHP150 Manual de Usario

27 Octubre 2024
JennAir

JennAir JGRP436HL Manual de Usario

27 Octubre 2024
Neff

Neff C17MS22G1 Manual de Usario

27 Octubre 2024
Pit Boss

Pit Boss BK24 Manual de Usario

27 Octubre 2024
Guzzanti

Guzzanti GZ-8206 Manual de Usario

27 Octubre 2024