Hotpoint FMG 1023B EU Manual de Usario

Hotpoint lavadora FMG 1023B EU

Lee a continuación 📖 el manual en español para Hotpoint FMG 1023B EU (24 páginas) en la categoría lavadora. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/24
1
GB
WASHING MACHINE
Instructions for use
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water and electricity supplies
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Opening the porthole door manually
Description of the washing machine, 6-7
Control panel
Display
Running a wash cycle, 8
Wash cycles and options, 9
Table of programmes and wash cycles
Wash options
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 11
Service, 12
FMG 1023
English,1
GB
ΕΛΛΗΝΙΚΑ,13
GR
2
GB
Installation
! This instruction manual should be kept in a safe
place for future reference. If the washing machine
is sold, transferred or moved, make sure that the
instruction manual remains with the machine so
that the new owner is able to familiarise himself/
herself with its operation and features.
! Read these instructions carefully: they
contain vital information relating to the safe
installation and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its
packaging.
2. Make sure that the washing machine has
not been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with
the installation process.
3. Remove the 4
protective screws
(used during
transportation)
and the rubber
washer with the
corresponding
spacer, located on
the rear part of the
appliance ( ).see figure
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will
need them again if the washing machine
needs to be moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing machine on a flat sturdy
floor, without resting it up against walls,
furniture cabinets or anything else.
2. If the floor is
not perfectly level,
compensate for
any unevenness
by tightening or
loosening the
adjustable front
feet ( ); the see figure
angle of inclination,
measured in relation
to the worktop, must
not exceed 2°.
Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washing machine.
Connecting the electricity and
water supplies
Connecting the water inlet hose
1. Connect the inlet
hose by screwing it to
a cold water tap using
a 3/4 gas threaded
connection (see
figure).
Before performing
the connection, allow
the water to run freely
until it is perfectly
clear.
2. Connect the
inlet hose to the
washing machine by
screwing it onto the
corresponding water
inlet of the appliance,
which is situated on
the top right-hand
side of the rear part
of the appliance (see
figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the range of values indicated in the Technical
data table (see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
3
GB
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drain duct or
a wall drain situated
between 65 and 100
cm from the floor;
alternatively, placed
it over the edge
of a basin, sink or
tub, fastening the
duct supplied to
the tap ( ). see figure
The free end of the
hose should not be
underwater.
! We advise against the use of hose
extensions; if it is absolutely necessary, the
extension must have the same diameter as the
original hose and must not exceed 150 cm in
length.
Electrical connections
Before plugging the appliance into the
electricity socket, make sure that:
• the socket is earthed and complies with all
applicable laws;
• the socket is able to withstand the
maximum power load of the appliance as
indicated in the Technical data table (see
opposite);
• the power supply voltage falls within the
values indicated in the Technical data table
( );see opposite
• the socket is compatible with the plug of
the washing machine. If this is not the case,
replace the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is
extremely dangerous to leave the appliance
exposed to rain, storms and other weather
conditions.
65 - 100 cm
! When the washing machine has been
installed, the electricity socket must remain
within easy reach.
! Do not use extension cords or multiple
sockets.
! The cable should not be bent or
compressed.
! The power supply cable must only be
replaced by authorised technicians.
Warning! The company shall not be held
responsible in the event that these standards
are not observed.
The first wash cycle
Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using
wash cycle number auto clean (see “Cleaning
the washing machine”).
Technical data
Model FMG 1023
Dimensions width 59.5 cm
height 85 cm
depth 60.5 cm
Capacity from 1 to 10 kg
Electrical
connections
please refer to the technical
data plate fixed to the ma-
chine
Water con-
nections
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 71 litres
Spin speed up to 1200 rotations per
minute
Test wash
cycles in
accordan-
ce with
directives
1061/2010
1015/2010
programme 4
;
Cotton Standard 60°C.
programme 5
;
Cotton Standard 40°C.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electroma-
gnetic Compatibility)
- 2006/95/EC (Low Voltage)
- 2012/19/EU

Especificaciones del producto

Marca: Hotpoint
Categoría: lavadora
Modelo: FMG 1023B EU

¿Necesitas ayuda?

Si necesitas ayuda con Hotpoint FMG 1023B EU haz una pregunta a continuación y otros usuarios te responderán


lavadora Hotpoint Manuales

Hotpoint

Hotpoint WMG 942BV EU Manual de Usario

19 Octubre 2024
Hotpoint

Hotpoint NSWM 963C W UK Manual de Usario

14 Octubre 2024
Hotpoint

Hotpoint HDA3420ZBB Manual de Usario

9 Octubre 2024
Hotpoint

Hotpoint VLXR1020DWO Manual de Usario

8 Octubre 2024
Hotpoint

Hotpoint NBT 1048 WD A IT Manual de Usario

6 Octubre 2024
Hotpoint

Hotpoint NBT 108 BLACK IT Manual de Usario

6 Octubre 2024
Hotpoint

Hotpoint HDA3600NBB Manual de Usario

6 Octubre 2024
Hotpoint

Hotpoint NM11 946 BC A UK Manual de Usario

6 Octubre 2024
Hotpoint

Hotpoint NM10 944 GS UK Manual de Usario

6 Octubre 2024
Hotpoint

Hotpoint NSWR 963C WK UK Manual de Usario

4 Octubre 2024

lavadora Manuales

Últimos lavadora Manuales

AEG

AEG LTR8C6152A Manual de Usario

27 Octubre 2024
Samsung

Samsung WW90T534ATW Manual de Usario

27 Octubre 2024
Samsung

Samsung WW10T754DBX Manual de Usario

27 Octubre 2024
New Pol

New Pol XF6600EL Manual de Usario

27 Octubre 2024
Zanussi

Zanussi ZR8441WF Manual de Usario

27 Octubre 2024
Philco

Philco PLDS 1063 Crown Manual de Usario

27 Octubre 2024
Candy

Candy CO 4104TWM/1-S Manual de Usario

27 Octubre 2024
New Pol

New Pol XS 271EV Manual de Usario

27 Octubre 2024
Corberó

Corberó CLAV822 Manual de Usario

27 Octubre 2024
Candy

Candy CBD485D2CE/1-80 Manual de Usario

27 Octubre 2024