Hotpoint RPD 10457 J UK Manual de Usario

Hotpoint lavadora RPD 10457 J UK

Lee a continuación 📖 el manual en español para Hotpoint RPD 10457 J UK (16 páginas) en la categoría lavadora. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/16
GB
1
Contents
Installation, 2-3-4-5
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 6
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 7
General safety
Disposal
Opening the porthole door manually
Description of the washing machine, 8-9
Control panel
Display
Running a wash cycle, 10
Wash cycles and functions, 11
Table of wash cycles
Wash functions
Detergents and laundry, 12
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 13-14
Product Guarantee and Repair Information, 15
RPD 10457 J
Instructions for use
WASHING MACHINE
English,1
GB
2
GB
Installation
2. If the floor is not perfectly level, compensate
for any unevenness by tightening or loosening
the adjustable front feet the an-(see figure);
gle of inclination, measured according to the
worktop, must not exceed 2°.
Levelling your appliance correctly will provide
it with stability and avoid any vibrations, noise
and shifting during operation. If it is placed on
a fitted or loose carpet, adjust the feet in such
a way as to allow enough room for ventilation
beneath the washing machine.
Electric and water connections
Connecting the water inlet hose
1. Connect the sup-
ply pipe by screwing
it to a cold water tap
using a 3/4 gas thre-
aded connection (see
figure).
Before performing the
connection, allow the
water to run freely un-
til it is perfectly clear.
2. Connect the other
end of the water inlet
hose to the washing
machine,
screwing it onto the
appliance’s cold water
inlet, situated on the
top right-hand side on
the rear of the ap-
pliance (see figure).
3. Make sure there are no kinks or bends in the
hose.
! The water pressure at the tap must be within
the values indicated in the Technical details
table (on the page 5).
! If the water inlet hose is not long enough,
contact a specialist store or an authorised
serviceman.
! Ensure that the supply taps are allowing wa-
ter through. Old taps may seize in the closed
position and thus prevent water reaching the
machine.
! Never use second-hand or old inlet hoses;
use the products supplied with the machine.
! Keep this instruction manual in a safe place
for future reference. Should the appliance be
sold, transferred or moved, make sure the
instruction manual accompanies the washing
machine to inform the new owner as to its
operation and features.
! Read these instructions carefully: they contain
vital information on installation, use and safety.
Unpacking and levelling
Unpacking
! This is a separate
part of the polystyre-
ne base and should
be removed with the
base.
! IMPORTANT check
when unpacking
your machine.
1. Unpack the washing
machine.
2. Check whether the
washing machine has
been damaged during
transport. If this is the
case, do not install
it and contact your
retailer.
3. Remove the 4 pro-
tective screws and the rubber bush with the
respective spacer, situated on the rear of the
appliance (see also the installation leaflet).
4. Seal the gaps using the plastic plugs provided.
5. Keep all the parts: you will need them again
if the washing machine needs to be moved to
another location.
! Packaging materials are not children’s toys.
Levelling
Your machine may make a considerable
amount of noise if the two front feet have not
been adjusted correctly.
1. Install the washing
machine on a flat sturdy
floor, without resting it up
against walls, cabinets
or anything else.
GB
3
Connecting the drain hose
Connect the drain
hose, without ben-
ding it, to a draining
duct or a wall drain
situated between 65
and 100 cm from the
floor;
The drain hose may
be connected to
an under-sink trap.
Before connecting
the drain hose from
the machine ensure
that any blanks or
removable ends have
been taken off the
spigot.
If it is placed over
the edge of a basin
or sink be sure the
free end of the hose
should not be under-
water.
! We advise against the use of hose extensions;
in case of absolute need, the extension must
have the same diameter as the original hose
and must not exceed 150 cm in length.
Ensure that if the drain hose is pushed into
a standpipe, that the end does not go down
more than 15cms (6 inches). If the hose is pu-
shed down too far, this may cause the machine
to self -syphon ie. continuously empty as it is
filling.
Electric connection
Before plugging the appliance into the mains
socket, make sure that:
the socket is earthed and in compliance with
the applicable law;
the socket is able to sustain the appliance’s
maximum power load indicated on the Tech-
nical Data Plate fixed on the machine;
the supply voltage is included within the
values indicated on the Technical Data Plate
fixed on the machine.
• the socket is compatible with the washing
machine’s plug. If this is not the case, repla-
ce the socket or the plug.
Your appliance is now supplied with a 13 amp
fused plug it can be plugged into a 13 amp
socket for immediate use. Before using the
appliance please read the instructions below.
WARNING - THIS APPLIANCE MUST BE
EARTHED.
THE FOLLOWING OPERATIONS SHOULD
BE CARRIED OUT BY A QUALIFIED ELECTRI-
CIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be
used, and the fuse cover re-fitted. If the fuse
cover is lost, the plug must not be used until a
replacement is obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be
of the correct colour as indicated by the colou-
red marking or the colour that is embossed in
words on the base of the plug. Replacements
can be obtained directly from your nearest
Service Depot.
Removing the plug:
If your appliance has a non-rewireable moul-
ded plug and you should wish to re-route the
mains cable through partitions, units etc.,
please ensure that either:
the plug is replaced by a fused 13 ampere
rewireable plug bearing the BSI mark of ap-
proval.
or:
the mains cable is wired directly into a 13
amp cable outlet, controlled by a switch, (in
compliance with BS 5733) which is accessible
without moving the appliance.
Disposing of the plug:
Ensure that before disposing of the plug itself,
you make the pins unusable so that it cannot
be accidentally inserted into a socket.
Instructions for connecting cable to an alternati-
ve plug:
Important: the wires in the mains lead are co-
loured in accordance with the following code:
Green & Yellow Earth
Blue Neutral
Brown Live
65 - 100 cm
Where it connects to
the waste water pipe
cut end off spigot or
remove the blanking cap

Especificaciones del producto

Marca: Hotpoint
Categoría: lavadora
Modelo: RPD 10457 J UK

¿Necesitas ayuda?

Si necesitas ayuda con Hotpoint RPD 10457 J UK haz una pregunta a continuación y otros usuarios te responderán




lavadora Hotpoint Manuales

lavadora Manuales

Últimos lavadora Manuales