HQ Power vdl20st Manual de Usario

Lee a continuación 📖 el manual en español para HQ Power vdl20st (13 páginas) en la categoría Maquina de efectos. Esta guía fue útil para 11 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/13
VDL20ST
STROBOSCOPE 20 W
STROBOSCOOP 20 W
STROBOSCOPE 20 W
ESTROBOSCOPIO 20 W
STROBOSKOP 20 W
USER MANUAL 2
GEBRUIKERSHANDLEIDING 4
NOTICE D’EMPLOI 6
MANUAL DEL USUARIO 8
BEDIENUNGSANLEITUNG 10
VDL20ST Rev. 03
13.11.2009 ©Velleman nv
2
USER MANUAL
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle
could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal
waste; it should be taken to a specialized company for recycling. This device should be
returned to your distributor or to a local recycling service. Respect the local environmental
rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing HQPower! Please read the manual thoroughly before bringing this device into
service. If the device was damaged in transit, don't install or use it and contact your dealer.
2. Safety Instructions
Indoor use only.
Keep the stroboscope away from rain, moisture, splashing and dripping liquids.
Protect the device against extreme heat and dust. Never put objects filled with liquid
on top of the device.
Risk of electroshock during installation.
Touching live wires can cause life-threatening electroshocks. Wait 5 minutes after
disconnecting the stroboscope from the mains before handling the device. Make sure not
to make contact with the mains plug contacts after disconnection.
DO NOT disassemble or open the cover(s).
Keep out of reach of children and unauthorized users or users with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instructions concerning use of the
appliance by a person responsible for their safety. Children should be supervised
to ensure that they do not play with the device.
Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and
the dealer will not accept responsibility for any ensuing defects or problems.
A qualified technician should install and service this device.
Do not switch the device on immediately after it has been exposed to changes in temperature. Protect
the device against damage by leaving it switched off until it has reached room temperature.
This device falls under protection class II. It is therefore essential that the device be earthed. Have a
qualified person carry out the electric connection.
Make sure that the available voltage does not exceed the voltage stated in the specifications of this
manual.
Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if
necessary.
Disconnect the device from the mains to clean it or when it is not in use. Handle the power cord by the
plug only.
There may be some smoke or a particular smell when the device is activated for the first time. This is
normal and any smoke or smell will gradually disappear.
Do not look directly at the light source as sensitive people may go into epileptic seizure if they do.
Note that damage caused by user modifications to the device is not covered by the warranty.
Do not operate the stroboscope without or with a cracked glass pane. Have it replaced when it is
damaged.
3. General Guidelines
Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.
This stroboscope should only be used indoors with an alternating current of max. 230 VAC ~ 50 Hz.
Do not shake the device. Avoid brute force when installing or operating the device.
Select a location where the device is protected against extreme heat, dust and moisture. Respect a
minimum distance of 0.5 m between the device’s light output and any illuminated surface.
VDL20ST Rev. 03
13.11.2009 ©Velleman nv
3
Familiarise yourself with the functions of the device before actually using it. Do not allow operation by
unqualified people. Any damage that may occur will most probably be due to unprofessional use of the
device.
Use the original packaging if the device is to be transported.
All modifications of the device are forbidden for safety reasons.
Only use the device for its intended purpose. All other uses may lead to short circuits, burns,
electroshocks, lamp explosion, crash, etc. Using the device in an unauthorised way will void the
warranty.
4. Installation
The installation construction should be able to support a minimum point load of 10 times the weight of
the device.
The installation must always be secured with a secondary attachment e.g. a safety cable (VDLSC7 or
VDLSC8).
Never stand directly below the device when it is being mounted, removed or serviced. Have a qualified
technician check the device once a year and once before you bring it into service.
Overhead mounting requires extensive experience: calculating workload limits, determining the
installation material to be used… Have the material and the device itself checked regularly. Do not
attempt to install the device yourself if you lack these qualifications as improper installation may result
in injuries.
The installation has to be approved by an expert before the device is taken into service.
The glass pane has to be replaced when it is damaged.
5. Use
1. Connect the stroboscope to the mains.
2. Set the flash frequency (0 to 10 flashes per second) by means of the knob at the rear.
3. Adjust the desired inclination angle via the mounting bracket and tighten the bracket screws.
6. Maintenance
1. All screws should be tightened and free of corrosion.
2. The housing, the glass pane, the mounting supports and the installation location (e.g. ceiling,
suspension, trussing) should not be deformed, modified or tampered with.
3. The electric power supply cables must not show any damage. Have a qualified technician maintain the
device.
4. Disconnect the device from the mains prior to maintenance activities.
5. Wipe the device regularly with a moist, lint-free cloth. Do not use alcohol or solvents.
6. There are no user-serviceable parts. Only authorized dealers may maintain and service this device.
7. Technical Specifications
power supply max. 230 VAC ~ 50 Hz
power consumption 20 W
dimensions 85 x 125 x 53 mm
total weight 240 g
lamp LAMP20ST (20 W)
Use this device with original accessories only. Velleman nv cannot be held responsible in the
event of damage or injury resulted from (incorrect) use of this device. For more info
concerning this product, please visit our website www.hqpower.eu. The information in this
manual is subject to change without prior notice.
© COPYRIGHT NOTICE
This manual is copyrighted. The copyright to this manual is owned by Velleman nv.
All worldwide rights reserved. No part of this manual may be copied, reproduced, translated or reduced
to any electronic medium or otherwise without the prior written consent of the copyright holder.

Especificaciones del producto

Marca: HQ Power
Categoría: Maquina de efectos
Modelo: vdl20st

¿Necesitas ayuda?

Si necesitas ayuda con HQ Power vdl20st haz una pregunta a continuación y otros usuarios te responderán




Maquina de efectos HQ Power Manuales

Maquina de efectos Manuales

Últimos Maquina de efectos Manuales