Hunter Outdoor Original 25602 Manual de Usario

Hunter Ventilador Outdoor Original 25602

Lee a continuación 📖 el manual en español para Hunter Outdoor Original 25602 (8 páginas) en la categoría Ventilador. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/8

S I N C E 1 8 8

INSTALLATION INSTRUCTIONS FOR

HUNTER ORIGINAL® CEILING FANS

WARNINGS

• To avoid possible electrical shock, before wir-

ing fan, disconnect power by turning off the cir-

cuit breakers both to the outlet box and to its

associated wall switch location. If you cannot

lock the circuit breakers in the “OFF” position,

securely fasten a prominent warning device,

such as a tag, to the service panel.

• All wiring must be in accordance with national

and local electrical codes. If you are unfamiliar

with wiring, you should use a qualified electri-

cian.

• To reduce the risk of personal injury, install the

fan to the building structure according to these

instructions and use only the hardware sup-

plied.

IMPORTANT!

READ AND SAVE THESE

INSTRUCTIONS!

CAUTIONS

• NEVER REST THE FAN ON THE SWITCH HOUS-

ING. As you prepare the fan for installation, rest

the motor in the liner in which it was packed.

• Be sure to put full contents of the oil tube into

the fan according to the instructions.

• If this fan is used as a replacement for an Origi-

nal® Old-Tyme non-reversible fan, it must be in-

stalled per the instructions included with this

fan. Failure to do so could result in the fan fall-

ing. DO NOT HANG THIS FAN ON A SINGLE

“J” HOOK.

• To reduce the risk of noise and to ensure proper

fan operation, do not use a solid-state speed

control with this fan. Use Hunter speed con-

trols for Hunter Original® ceiling fans only.

• Do not use an abrasive cleaner on the fan. A

mild detergent will clean and restore most units

to their original beauty.

Installing Your Hunter® Ceiling

Fan

Note To Installers: Please leave this manual with

the home owner.

Tools needed:

• Pliers • 3/8” Socket Wrench

• Flat blade screwdriver • Phillips screwdriver

• Electric drill • 11/64” drill bit

• 4” x 1-1/2” standard octagon electrical box

Step 1: Pre-Installation

1. Select the installation site: Normally this is

near the center of the room, often replacing a light

fixture. Make certain that ample clearance is left

for the rotating fan blades. For maximum effi-

ciency, no obstructions (walls, posts, etc.) should be

within 24” of the tips of the blades. See Figure 1.

NOTE: Mounting should also meet the precautions listed

in Step 3.

Read this entire manual thoroughly before begin-

ning installation.

24”

Minimum

Clearance

7’ Minimum

Clearance To

Floor

8’Minimum

to Ceiling

Figure 1

2. Fan mounting height: Your Hunter fan

comes with the proper hardware to hang the fan

from a standard 8 foot ceiling so that the fan blades

will be 12” from the ceiling and approximately 7

feet from the floor. See Figure 1.

NOTE: On vaulted ceilings, up to 45° pitch, you must

use the Hunter Vaulted Ceiling Mounting Kit.

Step 2: Inspect the Fan

1. Unpack the fan carefully to avoid any damage to components.

Figure 2

CAUTION

• Never lift the motor by the wires. Let the motor rest in the carton liner for protection.

2. Check the sack parts. See Figure 2.

Blade Assembly

Screw

Armature Screw

Pull Chain

1/4-10 Lag Screw

Mounting Bracket

Pipe Nipple

Oil Tube

Motor / Housing Assembly

Blade Set

Blade Iron Set

Hardware

(Drawn to Scale)

Fan Parts

(Not Drawn to Scale)

Canopy

Rubber Bushing / Pin

Hanger Bracket

Assembly

Canopy

Insert

Wire Nut

Canopy Screw

Mounting Isolator

41556-0 1 8/0 8 / 0 3 © 2 0 03 HU NTER F A N CO.

Step 3: Installation of Ceiling Mounting

Hardware

2” x 4” Wood Brace

Outlet Box

Ceiling

Joist

Ceiling

M4 Wood Screw &

Washer (2) Required

Figure 3

2. Drill two (2) 1/4” diameter holes 2-9/16”

apart through the back of the outlet box into the

cross brace. There may be two holes at the correct

spacing, but they will probably have to be enlarged.

3. Use the two (2) bracket screws to secure the

hanger bracket and canopy plate to the joist as

shown in Figure 4. Install the rubber bumpers into

the canopy plate and the rubber bushing in the

hanger bracket before assembling the parts to the

ceiling joist.

Rubber

Bumpers

Figure 4

Step 4: Hanging the Fan

• When inspecting or preparing the installation

site where wiring is available, to avoid possible

electrical shock, disconnect power by turning off the

circuit breakers both to the outlet box and to its

associated wall switch location. If you cannot lock

the circuit breakers in the off position, securely

fasten a prominent warning device, such as a tag, to

the service panel.

• All wiring must be in accordance with na-

tional and local electrical codes. If you are unfamil-

iar with wiring, you should use a qualified electri-

cian.

• Do not mount directly to an unsupported

ceiling or to an electrical outlet box.

• The wood joist chosen for mounting the fan

must be sound and of sufficient size. In no case

should it be smaller than standard 2”x4” lumber.

1. Secure a metallic outlet box 4” x 1-1/2” or

4” x 1/2” deep to a 2” x 4” cross brace between two

ceiling joists as shown in Figure 3. The outletbox

must be recessed in the ceiling by 1/16” minimum.

Secure the outlet box to the cross brace by drilling

two (2) pilot holes no larger than the minor diameter

of the woodscrews (5/64”) and use two #8 x 1-1/2”

woodscrews and washers. Use the innermost holes

for securing the box. Orient the box so the outer-

most holes are aligned with the 2” x 4” brace. The

outermost holes will be use in Step 3 sub-step 2.

CAUTION

• Your Hunter ceiling fan weighs up to 50 lbs. The

following precautions must be taken for safety,

and to ensure that your fan is securely mounted

to the ceiling.

CAUTION

• Do not use a lubricant on the screws.

CAUTION

• Do not use a lubricant on the screws.

CAUTIONS

• Be sure to tighten the pipe nipple shown in Fig-

ure 2 into the fan, tighten the hanger bracket

onto the pipe, and tighten the two set screws

as described in sub-step 2 to prevent the fan

from falling.

• Your fan may weigh up to 50 lbs. All of the fol-

lowing steps must be followed in order to en-

sure a secure mounting. Perform sub-steps 1-

4 with the motor resting in the liner for protec-

tion.

1. Take the hanger bracket from the sack parts

and locate the pipe nipple (See Figure 2.). Feed the

wires from the top of your motor through the pipe.

2. Back out the set screw in the neck of the

motor housing and the hanger bracket so the pipe

can be screwed in. Screw the pipe into the fan until

tight (at least 4-1/2 turns). Feed the wire through

the canopy and the canopy insert and let the canopy

rest on the neck of the motor. Slide the canopy

insert over the pipe.Feed the wire through the

hanger bracket and screw the hanger bracket onto

the pipe until tight (at least 3 turns). Then use pliers

to tighten both the hanger bracket and the pipe

together. Tighten the set screw in the motor housing

with pliers. Securely tighten the set screw in the

hanger bracket. See Figure 5.

Especificaciones del producto

Marca:	Hunter
Categoría:	Ventilador
Modelo:	Outdoor Original 25602

¿Necesitas ayuda?

Si necesitas ayuda con Hunter Outdoor Original 25602 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

Ventilador Hunter Manuales

Hunter Bayport Manual de Usario

27 Octubre 2024

Hunter Cabo Manual de Usario

27 Octubre 2024

Hunter Grove Park 50341 Manual de Usario

19 Septiembre 2024

Hunter Charlotte 50402 Manual de Usario

19 Septiembre 2024

Hunter Claudette 59622 Manual de Usario

19 Septiembre 2024

Hunter Havoc 59470 Manual de Usario

19 Septiembre 2024

Hunter Starklake 50409 Manual de Usario

19 Septiembre 2024

Hunter Port Royale 50390 Manual de Usario

19 Septiembre 2024

Hunter Midtown 54211 Manual de Usario

19 Septiembre 2024

Hunter Donegan 53336 Manual de Usario

19 Septiembre 2024

Ventilador Manuales

Últimos Ventilador Manuales

CasaFan Eco Plano II Manual de Usario

27 Octubre 2024

Eldom Columbiavac CP60 Manual de Usario

26 Octubre 2024

V-Tac VT-6055-3 Manual de Usario

26 Octubre 2024

V-Tac VT-6053-5 Manual de Usario

26 Octubre 2024

Thermex TD-Silent Manual de Usario

25 Octubre 2024

Ufesa Toronto FF0450 Manual de Usario

25 Octubre 2024

Cecotec EnergySilence 300 Max Skyline Smart Manual de Usario

25 Octubre 2024

Westinghouse 72250 Manual de Usario

25 Octubre 2024

Yamazen FCR-HT401 Manual de Usario

23 Octubre 2024

Yamazen FCR-BWG403 Manual de Usario

23 Octubre 2024