Indesit BWE 71496X SV UK Manual de Usario

Indesit lavadora BWE 71496X SV UK

Lee a continuación 📖 el manual en español para Indesit BWE 71496X SV UK (7 páginas) en la categoría lavadora. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/7
GB
User Manual
CONTROL PANEL
1. ON/OFF button
2. START/PAUSE button and indicator light
3. TEMPERATURE button
4. DISPLAY
5. buttonCHILD LOCK
6. OPTION button
7. button DELAYED START
8. SPIN button
9. WASH CYCLE SELECTOR KNOB
10. PUSH & GO button
WASH CYCLE TABLE
PRODUCT DESCRIPTION
1.
3.
2.
5.
4.
7.
6.
8.
1. Top
2. Detergent dispenser drawer
3. Control panel
4. Handle
5. Porthole door
6. Drain pump (behind the plinth)
7. Plinth (removable)
8. Adjustable feet (2)
1
9
2 3 5
678
10
4
Before using the appliance carefully read the Safety Instruction.
Before using the machine, it is imperative that the transport bolts are removed.
For more detailed instructions on how to remove them, see the Installation Guide.
* By selecting the cycle and excluding the spin cycle, the washing machine will drain only.
** The duration of the wash cycles can be checked on the display.
*** After programme end and spinning with maximum selectable spin speed, in default
programme setting.
**** The display will show the suggested spin speed as default value.
The cycle duration indicated on the display or instruction manual is an estimate based on
standard conditions. The actual duration may vary in relation to several factors, such as the
temperature and pressure of the incoming water, ambient temperature, amount of detergent,
load quantity and type, load balancing and any additional options selected. The values given
for programmes other than the Eco 40-60 programme are indicative only.
1) Eco 40-60
-
Test wash cycle in compliance with EU Ecodesign regulation 2019/2014.
The most ecient programme in terms of energy and water consumption for washing
normally soiled cotton laundry.
Note: spin speed values shown on the display can slightly diers from the values stated in the
table.
For all testing institutes:
2) Long cotton cycle: set cycle 6 at a temperature of 40°C.
3) Long synthetics cycle: set cycle 7 at a temperature of 40°C.
DETERGENT DISPENSER DRAWER
Compartment 1:
Do not insert detergent in this compartment.
Compartment 2: Washing detergent (powder
or liquid)
If liquid detergent is used, the removable plastic
partition A (supplied) should be used for proper
dosage.
If powder detergent is used, insert the partition
into slot .B
Compartment 3: Additives (fabric softener, etc.)
The fabric softener must never exceed the “max
level indicated on the central pin.
! The detergent drawer is suitable only for Liquid
and Powder detergent. No Capsule Detergent allowed.
TheCapsule Detergent have to be placed into the drum before the load.
Make sure to use the correct Capsule Detergent dosage amount
recommended by Manufacturer.
! Use powder detergent for white cotton garments, for pre-washing, and
for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
! To remove the drawer, press lever and pull the drawer outwards.C
C
Maximum load 7 kg
Power input in o mode 0.5 W / in left-on mode 8 W
Detergents and
Additives
Recommended
detergent
Residual
dampness %
(***)
Energy con-
sumption kWh
Total water l
Laundry
temperature °C
Wash cycle Temperature Maxim spin
(r.p.m.)
Max.
load
(kg)
Duration
(h : m)
Wash Fabric
softener
Powder
Liquid
Capsule
(4)
Setting Range 2 3
1 Cotton 40°C 1000 7 ** – 40°C   – –
2 Shirt 40°C 600 2 **40°C   – –
3ARIEL PODS 30°C 30°C 1000 4.5 ** – – – –
4 Wool 40°C – 40°C 800 1.5 ** – –
5 20°C 20°C – 20°C 1400 7 1:50 52 0.160 64 22
6 Cotton (2) 40°C – 60°C 1400 7 3:40   50 450.980 75
7 Synthetics (3) 40°C – 60°C 1200 4 2:55   35 0.860 60 43
8 Mixed 40°C – 40°C 1400 7 **   – –
9Eco 40-60 (1) 40 °C 40°C
1351 7 3:25   53 0.635 54 34
1351 3.5 2:40   53 0.445 44 32
1351 2 2:25   53 0.187 35 23
10 White 60°C – 90°C 1400 7 2:30   52 1.360 75 55
11 Rapid 20min 20°C 800 1.5 ** – 20°C – –
11 Rapid 40°C – 40°C 1200 3.5 ** – –
11 Rapid 60°C – 60°C 1000 7 **   – –
12 Rapid 45min Full Load 40°C - 40°C 1200 7 ** – –
13 Duvet 30°C – 30°C 1000 3 **   – –
14 Delicates 30°C 30°C – 3C 600 (****) 1 ** – –
Rinse + Spin 1400 7 ** – –
Spin + Drain * 1400 7 ** – –
Required dosage - Optional dosage - 4) Minimum 30°C recommended for usage of Capsule detergent.
THANK YOU FOR BUYING A INDESIT PRODUCT
In order to receive a more complete assistance,
please register your product on
www.indesit.com/register
WASH CYCLES
Follow the instructions on the symbols of the garment’s wash
care label. The value indicated in the symbol is the maximum
recommended temperature for washing the garment.
Cotton
Cycle designed to wash cotton garments. During the last phase of the
cycle garments will be treated with steam, that will relax the bres.
Shirt
Use the special wash cycle to wash shirts in dierent fabrics and colours
to guarantee they receive the best possible care. During the last phase of
the cycle garments will be treated with steam, that will relax the bres.
ARIEL PODS
A 30°C short cycle designed to wash a mixed load of cotton and
synthetics fabrics, recommended for the use of PODS detergent.
Wool - Wool Care
The wool wash cycle of this machine has been approved by
The Woolmark Company for the washing of machine washable
wool products provided that the products are washed
according to the instructions on the garment label and those
issued by the manufacturer of this washing machine. The
Woolmark symbol is a Certication mark in many countries.
(M2232)
20°C
For washing lightly soiled cotton garments, at a temperature of 20 °C.
Cotton
Suitable for washing towels, underwear, table cloths, etc. made of
resistant linen and cotton that are moderately to heavily soiled.
Synthetics
Specic for synthetic items. If the dirt is dicult to remove, the temperature
can be increased up to 60° and powder detergent can be used too.
Mixed
A 40°C cycle for washing cotton and synthetic garments together.
Suitable for lightly soiled underwear.
Eco 40-60
For washing normally soiled cotton garments declared to be washable at 40 °C
or 60 °C, together in the same cycle. This is the standard cotton programme
and the most ecient in terms of water and energy consumption.
! As specied, this wash cycle only runs at 40 °C.
White
For heavily soiled whites and resistant colours.
Rapid 20min
Allows for varying the garment treatment duration from 20 to 60’.
- 20’: this cycle refreshes your garments in just 20 minutes.
- 45’: a short cycle designed for washing mixed cotton-synthetic
garments.
- 60’: this cycle is designed to wash moderately soiled resistant cotton
garments at 60°C in an hour, with good washing performance. For
synthetic or mixed garments, the temperature should be lowered to 40°C.
Rapid 45min Full Load
Suitable for washing a full load of cotton clothes moderately soiled in 45
minutes.
Duvet
For washing clothing padded with goose down, such as double or single
duvets (weighing under 3 kg), cushions or down jackets. Duvets should
be loaded into the drum with their edges folded inwards and no more
than ¾ of the total drum volume should be used up. For best results, it is
advisable to use liquid detergent to be poured into the detergent drawer.
Delicates 30°C
Suitable for washing very delicate garments. It is advisable to turn the
garments inside out before washing them. For best results, use liquid
detergent on delicate garments.
Rinse + Spin
Designed for rinsing and spinning.
Spin + Drain
Designed to spin and drain the water.
DISPLAY
The display is useful when programming the machine and provides a lot
of information.
C (see “Options”)
B
C
A
The duration of the available wash cycles and the remaining time of a
running cycle appear in section ; if the Delayed Start option has been A
set, the countdown to the start of the selected cycle will appear.
Pressing the corresponding button allows for viewing the maximum spin
speed and temperature values attained by the machine during the set
wash cycle, or the values selected most recently, if these are compatible
with the set wash cycle.
The hourglass ashes while the machine processes the data on the basis
of the selected cycle. After a maximum of 10 minutes, the icon remains
steady lit and the nal time remaining is displayed. The “hourglass” icon
will then switch o approximately 1 minute after the nal time remaining
has been displayed.
The “washing phases” relative to the selected cycle and the washing
phase” of the running cycle appear in section :B
Wash
Rinse
Spin
Drain
When lit, the symbol indicates that the set Delayed Start value has
appeared on the display.
There are three levels in section relative to the washing options.C
DOOR LOCKED INDICATOR
When lit, the symbol indicates that the door is locked. To prevent any
damage, wait until the symbol turns o before opening the door.
To open the door while a cycle is in progress, press the START/PAUSE
button ; if the symbol is o, the door can be opened.
FIRSTTIME USE
Once the appliance has been installed, and before it is used for the rst
time, run a wash cycle with detergent and no laundry, by setting the
Auto-Clean” cycle.
DAILY USE
Prepare the laundry by following the suggestions appearing under the
TIPS AND SUGGESTIONS” section.
Rapid programming
- Press the ON/OFF button ; the START/PAUSE indicator light will
ash slowly green.
- Open the door. Load the laundry while making sure not to exceed the
maximum load quantity indicated in the cycle table.
- Pull out the detergent dispenser drawer and pour the detergent into the
relevant compartments as described in “DETERGENT DISPENSER DRAWER
section.
- Close the door.
STARTING CYCLE
Press the PUSH & GO button.
The machine will lock the door ( symbol on) and the drum will start to
rotate; the door will be unlocked ( symbol o) and then locked again
( symbol on) as preparation phase of each washing cycle. The Clicking”
noise is part of the door locking mechanism. Water will enter the drum
and start the washing phase once the door is locked.
Traditional programming
- Press the ON/OFF button ; the START/PAUSE indicator light will
ash slowly green.
- Open the door. Load the laundry while making sure not to exceed the
maximum load quantity indicated in the Wash Cycle Table.
- Pull out the detergent dispenser drawer and pour the detergent into the
relevant compartments as described in “DETERGENT DISPENSER DRAWER
section.
- Close the door.
- Use the WASH CYCLE selector knob to select the desired wash cycle: it
will be associated with a specic temperature and spin speed that can be
modied. The duration of the cycle will appear on the display.
- Modify the temperature and/or spin speed: the machine automatically
displays the maximum temperature and spin speed values set for the
selected cycle, or the most recently-used settings if they are compatible
with the selected cycle. Pressing the button gradually reduces the
temperature down to the cold wash “OFF” setting. Pressing the button
gradually reduces the spin speed until it is completely excluded (“OFF
setting). Pressing these buttons again restores the maximum values.
- Select the desired options.
STARTING CYCLE
Press the START/PAUSE button.
The machine will lock the door ( symbol on) and the drum will start to
rotate; the door will be unlocked ( symbol o) and then locked again
( symbol on) as preparation phase of each washing cycle. The Clicking”
noise is part of the door locking mechanism. Water will enter the drum
and start the washing phase once the door is locked.
PAUSING A CYCLE
To pause the wash cycle, press the START/PAUSE button again; the
indicator light will ash amber. If the symbol is not lit, the door may be
opened. To start the wash cycle from the point at which it was
interrupted, press the START/PAUSE button again.
OPENING THE DOOR, IF NECESSARY
Once a cycle starts, the symbol turns on to signal that the door cannot
be opened. While a wash cycle is running, the door remains locked. To
open the door while a cycle is under way, for example, to add or remove
garments, press the START/PAUSE button to pause the cycle; the
indicator light will ash amber. If the symbol is not lit, the door may be
opened. Press the START/PAUSE button again to continue the cycle.
CHANGING A RUNNING WASH CYCLE
To change a wash cycle while it is in progress, pause the washing machine
using the START/PAUSE button (the relative indicator light will ash amber),
then select the desired cycle and press the START/PAUSE button again.
! To cancel a cycle that has already begun, press and hold the ON/OFF
button. The cycle will be stopped and the machine will switch o.
END OF THE CYCLE
This will be indicated by the word “END” on the display; when the
symbol switches o, the door may be opened. Open the door and switch
o the machine. If you do not press ON/OFF button, the washing
machine will switch o automatically after about a 10 minutes. Close the
water tap, open the door and unload the washing machine. Leave the
door ajar to allow the drum to dry.
OPTIONS
- If the selected option is not compatible with the set wash cycle, the
indicator light will ash and the option will not be activated.
- If the selected option is not compatible with another previously
selected option, the indicator light will ash accompanied by a buzzer
(3 beeps), and only the latter option will be activated; the indicator
light corresponding to the activated option will turn on.
Stain removal
This option allows for selecting the type of dirt so as to optimally adjust the
cycle for removing the stains. The following types of dirt can be selected:
- Food: for stains caused by foodstus and beverages, for example.
- : for grease and ink stains, for example.Work
- Outdoor: for mud and grass stains, for example.
! The wash cycle duration varies according to the type of selected dirt.
Rapid
When this button is pressed the rst time, the 45’ icon lights up, when
pressed the second time the 60’ icon lights up and the third time the 20’
icon lights up.
Delayed Start
To set a delayed start for the selected cycle, press the corresponding
button repeatedly until the desired delay period has been reached. When
this option has been activated, the symbol lights up on the display. To
remove the delayed start setting, press the button until the word “OFF”
appears on the display.
Temperature
Each wash cycle has a pre-dened temperature. To modify the
temperature, press the button. The value will appear on the display.
Spin
Each wash cycle has a pre-dened spin speed. To modify the spin speed,
press the button. The value will appear on the display.
PUSH & GO
To start the PUSH & GO cycle press and hold the relative button for
2 seconds. The lit indicator light indicates that the cycle has started.
This wash cycle is ideal for cotton or synthetic fabrics, as it washes at a
temperature of 30°C and a maximum spin speed of 1,200 rpm. Max load
3,5 kg (cycle duration 59’).
During the last phase of the cycle garments will be treated with steam, that
will relax the bres making ironing easier and quicker (Steam Tecnology).
How does it work?
1. Load the laundry (cotton and/or synthetic garments) and close the door.
2. Pour the detergent and additives.
3. Start the cycle by pressing and holding the PUSH & GO button for 2
seconds. The relevant indicator light will turn green and the door will lock
(the symbol lights up).
N.B.: starting the wash cycle through the PUSH & GO button activates an
automatic non-customisable cycle recommended for cotton and synthetic
fabrics. This cycle does not allow for setting any additional options.
To open the door while an automatic cycle is under way, press the START/
PAUSE button; if the locked door symbol is o, the door may be
opened. Press the START/PAUSE button again to restart the cycle from
the point at which it was interrupted.
4. At the end of the wash cycle the word END will appear on the display.
CHILD LOCK
To activate the control panel lock, press and hold the button for
approximately 2 seconds. The lit symbol signals that the control
panel is locked. This prevents wash cycles from being modied
accidentally (except for the ON/OFF button), especially if there are
children in the home. To deactivate the control panel lock, press and hold
the button for approximately 2 seconds.
TIPS AND SUGGESTIONS
Divide the laundry according to:
Type of fabric (cotton, mixed bres, synthetics, wool, garments to be
hand-washed). Colour (separate coloured garments from whites, wash new
coloured garments separately). Delicates (small garments such as nylon
stockings and items with hooks such as bras: insert them in a fabric bag).
Empty the pockets:
Objects such as coins or lighters can damage the washing machine and
the drum. Check all buttons.
Follow the dosage recommendation / additives
It optimizes the cleaning result, it avoids irritating residues of surplus
detergent in your laundry and it saves money by avoiding waste of surplus
detergent.
Use low temperature and longer duration
The most ecient programmes in terms of energy consumption are generally
those that perform at lower temperatures and longer duration.
Observe the load sizes
Load your washing machine up to the capacity indicated in the
“Wash Cycle Table table to save water and energy.
Noise and remaining moisture content
They are inuenced by the spinning speed: the higher the spinning speed
in the spinning phase, the higher the noise and the lower the remaining
moisture content.
CARE AND MAINTENANCE
Before performing cleaning and maintenance, switch the washing machine
o and disconnect it from the mains power. Do not use ammable liquids to
clean the washing machine. Clean and maintain your washing machine
periodically (at least 4 times per year).
Disconnect the water and power supplies
Close the water tap after every wash. This will limit wear on the hydraulic
system inside the washing machine and help to prevent leaks.
Unplug the washing machine when cleaning it and during all
maintenance work.
Clean the washing machine
The outer parts and rubber components of the appliance can be cleaned
using a soft cloth soaked in lukewarm soapy water. Do not use solvents or
abrasives.
The washing machine has a Auto-clean” cycle for its internal parts; it
must be run without any load in the drum.
To optimise this cycle, it is possible to use either detergent (10% of the
quantity specied for lightly soiled garments) or special additives to clean
the washing machine. We recommend running a cleaning cycle every 40
wash cycles.
To start the cycle press buttons and simultaneously for
5 seconds.
The cycle will start automatically and will run for about 70 minutes. To
stop the cycle, press the START/PAUSE button.
Clean the detergent dispenser drawer
Wash it under running water; this operation should be repeated
frequently.
Care for the door and drum
Always leave the porthole door ajar in order to prevent unpleasant odours
from forming.
Clean the pump
The washing machine is tted with a auto-cleaning pump that does not
require any maintenance. Small items (such as coins or buttons) may
sometimes fall into the protective pre-chamber situated at the base of the
pump.
! Make sure the wash cycle has ended and unplug the appliance.
To access the pre-chamber:
1. remove the cover panel on the front of the machine by rst pressing it
in the centre then pushing downwards on both sides to extract it;
2. loosen the drainage pump cover by turning it anti-clockwise: it is
normal for some water to leak out;
3. clean the inside thoroughly;
4. screw the cover back on;
5. put the panel back in place, making sure the hooks slot in place before
pushing the panel onto the appliance.
Check the water inlet hose
Check the water inlet hose at least once a year. If it is cracked or broken, it
must be replaced: during wash cycles, the high pressure of the water
could suddenly split the hose open.
! Never use hoses that have already been used.
LOAD BALANCING SYSTEM
Before every spin cycle, to avoid excessive vibrations before every
spin and to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the washing
rotation speed. If, after several attempts, the load is not balanced
correctly, the machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washing machine performs the distribution
process instead of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are mixed in the load.
ACCESSORIES
Contact our Technical Assistance Service to check whether the following
accessories are available for this washing machine model.
Stacking kit
With this accessory you can secure the tumble dryer to the upper part of
your washing machine to save space and facilitate loading and unloading
of the tumble dryer.
TRANSPORT AND HANDLING
Do not lift the washing machine by gripping it from the upper section.
Unplug the appliance and close the water tap. Check that the door and
detergent dispenser drawer are tightly closed. Detach the lling hose
from the water tap then detach the drain hose. Empty all the water
remaining in the hoses and secure the latter so that they do not get
damaged during transport. Apply the transport bolts back on. Repeat, in
reverse order, the transport bolt removal procedure described in the
“Health & Safety and Installation Guides.

Especificaciones del producto

Marca: Indesit
Categoría: lavadora
Modelo: BWE 71496X SV UK

¿Necesitas ayuda?

Si necesitas ayuda con Indesit BWE 71496X SV UK haz una pregunta a continuación y otros usuarios te responderán




lavadora Indesit Manuales

lavadora Manuales

Últimos lavadora Manuales