Indesit IP 641 S C IX Manual de Usario

Indesit horno IP 641 S C IX

Lee a continuación 📖 el manual en español para Indesit IP 641 S C IX (12 páginas) en la categoría horno. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/12

HOB

IP 640 S UK

IP 641 S C UK

IP 751 S C UK

Contents

Installation, 2-5

Positioning

Electrical connection

Gas connection

Data plate

Burner and nozzle specifications

Description of the appliance, 6

Overall view

Start- anup d use, 7

Practical advice on using the burners

Precautions an tid ps, 8

General safety

Disposal

Maintenance and care, 9

Switching the appliance off

Cleaning the appliance

Gas tap maintenance

Troubleshooting, 10

Operating Inst tionsruc

Eng hlis , 1

 Before operating your new appliance please read this

instruction booklet carefully. It contains important information

for safe use, installation and care of the appliance.

 Please keep these operating instructions for future

reference. Pass them on to possible new owners of the

appliance.

Positioning

 Keep packaging material out of the reach of children. It

can become a choking or suffocation hazard (see

Precautions and tips).

 The appliance must be installed by a qualified professional

according to the instructions provided. Incorrect installation

may cause harm to people and animals or may damage

property.

 This unit may be installed and used only in permanently

ventilated rooms in accordance with British Standard Codes

Of Practice: B.S. 6172 / B.S. 5440, Par. 2 and B.S. 6891

Current Editions. The following requirements must be

observed:

 The room must be equipped with an air extraction system

that expels any combustion fumes. This may consist of a

hood or an electric fan that automatically starts each time

the appliance is switched on.

 The room must also allow proper air circulation, as air is

needed for combustion to occur normally. The flow of air

must not be less than 2 m3/h per kW of installed power.

The air circulation system may

take air directly from the outside

by means of a pipe with an inner

cross section of at least 100 cm2;

the opening must not be

vulnerable to any type of

blockages.

The system can also provide the

air needed for combustion

indirectly, i.e. from adjacent rooms

fitted with air circulation tubes as

described above. However, these

rooms must not be communal

rooms, bedrooms or rooms that

may present a fire hazard.

 Liquid petroleum gas sinks to the floor as it is heavier

than air. Therefore, rooms containing LPG cylinders must

also be equipped with vents to allow gas to escape in

the event of a leak. As a result LPG cylinders, whether

partially or completely full, must not be installed or

stored in rooms or storage areas that are below ground

level (cellars, etc.). It is advisable to keep only the

cylinder being used in the room, positioned so that it is

not subject to heat produced by external sources

(ovens, fireplaces, stoves, etc. ) which could raise the

temperature of the cylinder above 50°C.

Fitting the appliance

Gas and mixed hobs are manufactured with type X

degree protection against overheating. The following

precautions must be taken when installing the hob:

 Kitchen cabinets adjacent to the appliance and taller

than the top of the hob must be at least 600 mm from

the edge of the hob.

 Hoods must be installed according to their relative

installation instruction manuals and at a minimum

distance of 650 mm from the hob.

 Place the wall cabinets adjacent to the hood at a

minimum height of 420 mm from the hob (see figure).

If the hob is installed beneath a

wall cabinet, the latter must be

situated at a minimum of 700 mm

above the hob (see figure).

 The installation cavity should have the dimensions

indicated in the figure. Fastening hooks are provided,

allowing you to fasten the hob to tops that are between

20 and 40 mm thick. To ensure the hob is securely

fastened to the top, we recommend you use all the

hooks provided.

555

475

Hoo fastening diagrak m

Hooking position Hooking position

for top H=20 mm for top H=30 mm

Installation

Enlarging the ventilation slot

between window and floor.

Adjacent

Room

Room to be

Vented

Examples of ventilation holes

for comburant air.

In a chimney stack or branched flue.

(exclusively for cooking appliances)

Directly to

the Outside

600mm min.

700mm min.

G B

Front

Hooking position Back

for top H=40 mm

 Use the hooks contained in the accessory pack

 Where the hob is not installed over a built-in oven, a

wooden panel must be installed as insulation. This

must be placed at a minimum distance of 20 mm from

the lower part of the hob.

Ventilation

To ensure adequate ventilation, the back panel of the

cabinet must be removed. It is advisable to install the

oven so that it rests on two strips of wood, or on a

completely flat surface with an opening of at least 45 x

560 mm (see diagrams).

! The hob can only be installed above built-in ovens with a

cooling ventilation system.

Electrical onne c ction

The cooktops fitted with a tripolar electrical supply

cord are designed to be be used with alternating

current according to the indications on the rating

plate located under the cooktop. The earthing wire

can be identified by its yellow-green colour.

In the case of installation over a built-in electric

oven, the electrical connections for the cooktop and

oven should be independent, not only for safety

purposes, but also to facilitate removal of one or

both in the future.

Elec rical ec Gast Conn t oion f r Coo tokp

Fit the supply cord with a standard plug for the

demand rate indicated on the rating plate or connect

it directly to the electrical mains. In the latter case, a

single pole switch must be placed between the

appliance and the mains, with a minimum opening

between the contacts of 3 mm in compliance with

current safety codes (the earthing wire must not be

interrupted by the switch). The power supply cord

must be positioned so that it does not reach a

temperature in excess of 50°C above room

temperature at any point.

 The installer must ensure that the correct electrical

connection has been made and that it is compliant

with safety regulations.

Before making the actual connection, make sure

that:

 The fuse and electrical system can withstand the

load required by the appliance;

 That the electrical supply system is equiped with

an efficient earth hook-up according to the norms

and regulations prescribed by law;

 That the plug or switch is easily accessible.

 The wires in the mains lead are coloured in

accordance with the following code:

Green & Yellow - Earth

Blue - Neutral

Brown - Live

As the colours of the wires in the mains lead may

not correspond with the coloured markings

identifying the terminals in your plug, proceed as

follows:

Connect the Green & Yellow wire to the terminal

marked E or or coloured Green or Green &

Yellow.

Connect the Brown wire to the terminal marked L or

coloured Red.

Connect the Blue wire to the terminal marked N or

coloured Black.

 The cable must not be bent or compressed.

 The cable must be checked regularly and replaced

by authorised technicians only (see Assistance).

 The manufacturer declines any liability should

these safety measures not be observed.

Gas onne c ction

The appliance should be connected to the main gas supply

or to a gas cylinder in compliance with current national

regulations. Before carrying out the connection, make sure

the cooker is compatible with the gas supply you wish to

560 mm.

45 mm.

Especificaciones del producto

Marca:	Indesit
Categoría:	horno
Modelo:	IP 641 S C IX
Color del producto:	Zwart
Peso.:	850 g
Ancho:	163 mm
Profundidad:	100 mm
Altura:	56.2 mm
Material de la carcasa:	Metaal
Código de seguridad internacional (IP):	IP40
Indicadores LED:	LAN, PoE, Power
Entrada de voltaje CC:	24 - 56 V
Certificación:	CE, C-Tick, FCC, VCCI, LVD
Estándar de red:	IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u, IEEE 802.3x
Temperatura de almacenamiento:	-40 - 85 °C
Protección de voltaje de energía:	Over current, Short circuit
Humedad de almacenamiento:	5 - 95 procent
Sistema de suspensión para la pared.:	Ja
MDI/MDI-X automático:	Ja
Alimentación a través de Ethernet (PoE):	Ja
Capacidad de conmutación:	1.2 Gbit/s
Dirección MAC:	1000 entries
Número de puertos Ethernet RJ-45 de conmutación básica:	6
Tipo de conmutación básica de puertos Ethernet RJ-45:	Fast Ethernet (10/100)
Tecnología de cableado Ethernet de cobre:	10BASE-T, 100BASE-TX
Tamaño del búfer:	128 KB
Consumo de energía (típico):	126 W
Temperatura de funcionamiento (TT):	-40 - 75 °C
Humedad relativa de funcionamiento (VV):	5 - 95 procent
Presupuesto total de alimentación a través de Ethernet (PoE):	120 W
Cantidad de puertos Power over Ethernet (PoE):	4
almacenamiento y reenvio:	Ja
Tipos de cables compatibles:	Cat3, Cat4, Cat5, Cat5e
Alimentación por puerto Alimentación a través de Ethernet (PoE):	30 W
Velocidad de reenvío de paquetes (10 Mbps):	14880 pps
Velocidad de reenvío de paquetes (100 Mbps):	148000 pps