Intellijel Tête Manual de Usario

Lee a continuación 📖 el manual en español para Intellijel Tête (151 páginas) en la categoría No categorizado. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/151
Tête + Tetrapad Manual
Tête + Tetrapad
Recordable, Syncable, Multi-Dimensional Performance Touch Controller
IMPORTANT!
This manual discusses Tête and Tetrapad when the two are used together. Tetrapad, when used
without Tête, operates significantly different and has its own dedicated manual.
Manual Revision: 2019.12.11
Tête + Tetrapad Manual
TABLE OF CONTENTS
TABLE OF CONTENTS 1
COMPLIANCE 7
PART ONE: INSTALLATION 8
INSTALLATION 9
Installing Your Modules 9
Connecting Tête to Tetrapad 11
Setting Tetrapad’s DIP Switches 11
The microSD Card 12
PART TWO: OVERVIEW 13
OVERVIEW 14
TETRAPAD PANEL OVERVIEW 16
Tête PANEL OVERVIEW 19
Outputs 19
Inputs & Attenuverters 20
Controls 25
MODE OVERVIEW 27
PART THREE: COMBO MODE 28
COMBO MODE 29
Entering Combo Mode 31
Assigning a Function to a Pad 31
Main Screen & Menus in Combo Mode 33
Combo Mode: Unipolar Fader 34
Assigning Unipolar Fader Functionality To A Pad 35
Using Unipolar Faders 36
Slew Between Fader Settings 37
Page 1
Tête + Tetrapad Manual
Quantizing Fader Values 37
Combo Mode: Bipolar Fader 38
Assigning Bipolar Fader Functionality To A Pad 39
Using Bipolar Faders 40
Slew Between Fader Settings 41
Quantizing Fader Values 41
Combo Mode: Crossfader 42
Assigning Crossfader Functionality To A Pad 43
Selecting a Crossfader Type 44
Using Crossfaders 46
Slew Between Fader Settings 47
Combo Mode: Euclidean 48
Assigning Euclidean Functionality To A Pad 49
Using Euclidean Pads 50
Creating & Rotating Syncopated Patterns 52
Using Euclidean Pads as Simple Drum Pads 53
Slew Between Vertical Output Voltages 54
Quantizing Vertical Output Voltages 54
Combo Mode: Switches 55
Assigning Switch Functionality To A Pad 56
Using Switches 57
Combo Mode: LFO 58
Assigning LFO Functionality To A Pad 59
Using an LFO (Overview) 60
LFO Basics 60
Locking the LFO Rate 61
Attenuating the LFO Output 61
Unipolar, Bipolar and Quantized LFOs 62
Page 2
Tête + Tetrapad Manual
PART FOUR: NOTES MODE 63
NOTES MODE 64
Entering Notes Mode 66
Setting the Number of Virtual Keys 67
Tuning Mode 68
Choosing a Note Assignment Method 68
Set Notes by Scale 69
Assigning Notes to the Tetrapad ‘Keyboard’ w/Scale 71
Playing the Keyboard 72
Slew Between Notes 74
Set Notes by Chord 75
Assigning Notes to the Tetrapad ‘Keyboard’ w/Chord 77
Playing Chords 78
Slew Between Chords 79
Copying & Pasting Chords 79
Set Notes Manually 80
Assigning Notes to the Tetrapad ‘Keyboard’ Manually 82
Playing the Keyboard 83
Slew Between Notes 83
Rotating and Inverting 83
Copying & Pasting Notes 84
Edit View for Notes Mode 85
PART FIVE: VOLTAGES MODE 86
VOLTAGES MODE 87
Entering Voltages Mode 88
Setting the Number of Voltage Banks 89
Assigning Voltage Values 89
Manual Voltage Assignment 89
Random Voltage Assignment 91
Reset a Voltage 92
Page 3
Tête + Tetrapad Manual
PART SEVEN: LOOPING & SEQUENCING 135
THE LOOPER 136
Combo Mode Looping 137
Record & Play with Touch Sync 138
Record & Play with Looper Sync 140
Record & Play Unsynced 142
Overdubbing 143
The Encoder Bar (In Looper) 144
Combo Mode Encoder Bar (Looper) 144
Notes Mode Encoder Bar (Looper) 144
Voltages Mode Encoder Bar (Looper) 145
Save, Load, Rename and Delete Loops 146
THE SEQUENCER 147
Record & Play A Note Sequence 147
Recording a Note Sequence 148
Playing Back a Note Sequence 149
Record & Play A Voltage Sequence 150
Recording a Voltage Sequence 151
Playing Back a Voltage Sequence 152
Editing Sequences 153
Appending Sequences 153
Overwriting Sequences 154
Inserting Into Sequences 154
Overdubbing Sequences 155
Save, Load, Rename and Delete Sequences 156
Page 5
Tête + Tetrapad Manual
PART ONE:
INSTALLATION
Page 8
Tête + Tetrapad Manual
INSTALLATION
Intellijel Eurorack modules are designed to be used with a Eurorack-compatible case and power
supply. We recommend you use Intellijel cases and power supplies.
Before installing these modules in your case, you must ensure your power supply has a free power
header and sufficient available capacity to power the modules:
Sum up the specified +12V current draw for all modules, including the new ones. Do the same
for the -12 V and +5V current draw. The current draw will be specified in the manufacturer's
technical specifications for each module.
Compare each of the sums to specifications for your case’s power supply.
Only proceed with installation if none of the values exceeds the power supply’s specifications.
Otherwise you must remove modules to free up capacity or upgrade your power supply.
You will also need to ensure your case has enough free space (hp) to fit the new modules. To prevent
screws or other debris from falling into the case and shorting any electrical contacts, do not leave
gaps between adjacent modules, and cover all unused areas with blank panels. Similarly, do not use
open frames or any other enclosure that exposes the backside of any module or the power distribution
board.
You can use a tool like to assist in your planning. Failure to adequately power your ModularGrid
modules may result in damage to your modules or power supply. If you are unsure, please contact us
before proceeding.
Installing Your Modules
When installing or removing modules from your case
always turn off the power to the case and disconnect
the power cable. Failure to do so may result in
serious injury or equipment damage.
Ensure the 10-pin connector on the power cable is
connected correctly to each module before
proceeding. The red stripe on the cable must line up
with the -12V pins on the module’s power connector.
Different modules use different ways to indicate the
-12V pins. Some may be labelled with “-12V;” a white
stripe next to the -12V pins; the words “red stripe;” or
some combination of these. Additionally, some
modules may have shrouded headers, thus
preventing backward connections.
Page 9
Tête + Tetrapad Manual
Connecting Tête to Tetrapad
IMPORTANT: Tetrapad must be running version 3.0 firmware or higher. See
Firmware Version
Display
.
After connecting both the Tête and Tetrapad to power, you will need to connect the two modules to
each other. This is done using the included, small 6-wire i2C cable.
1. Connect one end of the cable to either of the two i2C 6-pin connectors on the back panel of
your Tetrapad, being sure to orient the red line with the white stripe on the circuit board. It
doesn’t matter which of Tetrapad’s two i2C connectors you use.
2. Connect the other end of the cable to either of the two shrouded i2C 6-pin connectors on the
back panel of your Tête. The connector is designed in such a way that it can only connect one
way. It doesn’t matter which of Tête’s two i2C connectors you use.
Setting Tetrapad’s DIP Switches
As shown in the illustration above, you will also need to configure some DIP switches on the back of
your Tetrapad in order for it to work with Tête. Specifically:
Make sure DIP switches 1 (SDA) and 2 (SCL) are set to the ON position.
Make sure DIP switches 3 (ID1) and 4 (ID0) are set to the OFF position.
Page 11

Especificaciones del producto

Marca: Intellijel
Categoría: No categorizado
Modelo: Tête

¿Necesitas ayuda?

Si necesitas ayuda con Intellijel Tête haz una pregunta a continuación y otros usuarios te responderán




No categorizado Intellijel Manuales

No categorizado Manuales

Últimos No categorizado Manuales