JANDY JEP-R Manual de Usario

JANDY Pompa JEP-R

Lee a continuación 📖 el manual en español para JANDY JEP-R (60 páginas) en la categoría Pompa. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/60

H0412200 Rev J

ENGLISH | FRAN AIS | ESPAÑOLÇ

WARNING

FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and

qualified in pool equipment by the jurisdiction in which the product will be installed where such state

or local requirements exist. The maintainer must be a professional with sufficient experience in pool

equipment installation and maintenance so that all of the instructions in this manual can be followed

exactly. Before installing this product, read and follow all warning notices and instructions that accompany

this product. Failure to follow warning notices and instructions may result in property damage, personal

injury, or death. Improper installation and/or operation will void the warranty.

Improper installation and/or operation can create unwanted electrical hazard which can

cause serious injury, property damage, or death.

ATTENTION INSTALLER - This manual contains important information about the

installation, operation and safe use of this product. This information should be given to

the owner/operator of this equipment.

INSTALLATION AND

OPERATION MANUAL

Jandy Pro Series

JEP-R

Variable-Speed Pump Digital Controller

For use with Jandy Pro Series Variable-Speed Pumps

For Indoor or Outdoor Installations

Table of Contents

DATE OF INSTALLATION

INSTALLER INFORMATION

INITIAL PRESSURE GAUGE READING (WITH CLEAN FILTER)

PUMP MODEL HORSEPOWER

FILTER MODEL SERIAL NUMBER

CONTROLLER MODEL SERIAL NUMBER

NOTES:

EQUIPMENT INFORMATION RECORD

Section 1. IMPORTANT

SAFETY INSTRUCTIONS 3 ...................

1.1 Safety Instructions 3 .............................................

1.2 Pool Pump Suction Entrapment Prevention

Guidelines 6 ..........................................................

Section 2. Installation of the

Digital Controller 7 ................................

2.1 Introduction ........................................................7

2.2 The Controller Panel 7 ..........................................

2.3 The Controller Components 7 ...............................

2.3.1 Additional materials 8 .....................................

2.4 Installation of the Backplate

onto an Electrical Box 8 ........................................

2.5 Installation of the Backplate

on a Flat Wall 8 .....................................................

2.6 Connection to Jandy® Pro Series

variable-speed Pump 8 .........................................

2.7 Variable Speed Pump Switch Settings 9 ..............

2.8 Connection to Remote Contacts 9 ........................

2.9 Remote Operation 10 .............................................

2.10 Remote Closure 4 Behavior 10 ...............................

2.11 Remote Closure 4 Application

- Booster Pump Support 10 ....................................

Section 3. User Operation of the Variable-Speed

Controller ............................................ 11

3.1 The Controller Interface .....................................11

3.2 Basic Functions .................................................11

3.3 OFF Mode ..........................................................11

3.4 RUN Mode .........................................................11

3.5 Manual Start and Stop 12 .......................................

3.6 Pump Speed Setting 12 ..........................................

3.7 Timeclock Setup and Operation.........................12

3.8 Keypad Lock 13 ......................................................

Section 4. Service Setup Options 13 .......................

4.1 Entering Service Setup 13 ......................................

4.2 Minimum and Maximum Pump Speeds 13 .............

4.3 Load Defaults 14 .....................................................

4.4 Last Fault 14 ...........................................................

4.5 Priming Speed and Duration 14 ..............................

4.6 eStar Speed 15 .......................................................

4.7 Pump Freeze Protect Operation 15 ........................

4.8 Selecting Pump Type .........................................15

4.9 Display Power Usage 15 ........................................

Section 5. User Set Up Options 16 ...........................

5.1 Setting Time-of-Day ...........................................16

5.2 Labeling Speeds 16 ................................................

5.3 General Labels 16 ..................................................

5.4 Custom Labels 16 ...................................................

5.5 Display Light Control 16 ..........................................

5.6 Language Selection 17 ...........................................

5.7 Run Duration (Speeds 3 and 4 Only) 17 .................

5.8 Password Protect 17 ...............................................

Section 6. Menu Flow Chart 18 .................................

PAGE 2

ENGLISH JEP-R Variable-Speed Pump Controller | Installation Manual

Section 1. IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

1.1 Safety Instructions

All electrical work must be performed by a licensed electrician and conform to all national, state, and local codes.

When installing and using this electrical equipment, basic safety precautions should always be followed, including the

following:

WARNING

RISK OF SUCTION ENTRAPMENT HAZARD, WHICH, IF NOT AVOIDED, CAN RESULT IN SERIOUS

INJURY OR DEATH. Do not block pump suction, as this can cause severe injury or death. Do not

use this pump for wading pools, shallow pools, or spas containing bottom drains, unless the pump is

connected to at least two (2) functioning suction outlets. Drain covers must be certified to the latest

published edition of ANSI®/ASME® A112.19.8 or its successor standard, ANSI/APSP-16.

WARNING

To reduce the risk of injury, do not permit children to use this product.

WARNING

To reduce the risk of property damage or injury, do not attempt to change the backwash (multiport, slide,

or full flow) valve position with the pump running.

WARNING

To reduce the risk of injury, do not remove the suction fittings of your spa or hot tub. Never operate a spa or hot tub if

the suction fittings are broken or missing. Never replace a suction fitting with one rated less than the flow rate marked

on the equipment assembly.

WARNING

Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs when the internal temperature

of the body reaches a level several degrees above the normal body temperature of 98.6°F (37°C). The symptoms

of hyperthermia include dizziness, fainting, drowsiness, lethargy, and an increase in the internal temperature of

the body. The effects of hyperthermia include: 1) unawareness of impending danger; 2) failure to perceive heat;

3) failure to recognize the need to exit spa; 4) physical inability to exit spa; 5) fetal damage in pregnant women;

6) unconsciousness resulting in a danger of drowning.

WARNING

To Reduce the Risk of Injury -

a The water in a spa should never exceed 104°F (40°C). Water temperatures between 100°F (38°C) and 104°F )

(40°C) are considered safe for a healthy adult. Lower water temperatures are recommended for young children

and when spa use exceeds 10 minutes.

b) Since excessive water temperatures have a high potential for causing fetal damage during the early months of

pregnancy, pregnant or possibly pregnant women should limit spa water temperatures to 100°F (38°C).

c) Before entering a spa or hot tub, the user should measure the water temperature with an accurate thermometer

since the tolerance of water temperature-regulating devices varies.

d) The use of alcohol, drugs, or medication before or during spa or hot tub use may lead to unconsciousness with

the possibility of drowning.

e) Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory system

problems, or diabetes should consult a physician before using a spa.

f) Persons using medication should consult a physician before using a spa or hot tub since some medication may

induce drowsiness while other medication may affect heart rate, blood pressure, and circulation.

PAGE 3

ENGLISH

JEP-R Variable-Speed Pump Controller | Installation Manual

Especificaciones del producto

Marca:	JANDY
Categoría:	Pompa
Modelo:	JEP-R
Color del producto:	Zwart
Peso.:	2800 g
Manual de usuario:	Ja
Fuente de alimentación:	100-240V 50/60Hz, 0, 8A
Tecnología de conectividad:	Bedraad
red LAN:	Ja
Tarjetas de memoria compatibles:	Memory Stick (MS), MMC, MS PRO, SD, SDHC
Resolución de grabación:	720 x 480 Pixels
Número de puertos USB 2.0:	3
Número de puertos HDMI:	1
Número de puertos Ethernet LAN (RJ-45):	1
Certificación:	CE, FCC, RoHs
Formato de señal analógica:	NTSC, PAL
Formato de imagen soportado:	BMP, GIF, JPG, PNG, TIF
Versión HDMI:	1.3
Sintonizador de TV integrado:	Ja
Cambio de hora:	Nee
Sistemas operativos compatibles:	Windows 2000 / XP / VISTA / 7\nMac OS X\nLinux
Velocidad de transferencia de datos de LAN inalámbrica (máx.):	300 Mbit/s
Número de puertos SCART:	1
Formatos de subtítulos admitidos:	ASS, SMI, SRT, SSA, SUB
Capacidad del disco duro:	1000 GB
Vídeo de grupo de componentes (YPbPr/YCbCr):	1
tipo de sintonizador de televisión:	DVB-T
Dimensiones (Ancho x Fondo x Alto):	342 x 207 x 55 mm
LED de enlace/actuación:	Ja
Tamaño del disco duro:	3.5 "
Ratio de transferencia:	480 Mbit/s
Wifi.:	Ja
CD ROM:	Ja