JBL GSB8 Manual de Usario

JBL Vocero GSB8

Lee a continuación 📖 el manual en español para JBL GSB8 (8 páginas) en la categoría Vocero. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/8
Installation Guide
GSB8 & GSB12 -In Ground Landscape Subwoofers
CAUTION: Installation must be done by qualified persons using safe
installation standards.
The installer is responsible for proper and selection and use of hardware to
install the speakers in a safe and durable manner.
Wire Connection
CABLE-- B - 1- - - s The GS speakers come with a captive multi conductor meter long cable with bare wire end for connection via an
external installer-provided weather proof - junction box.
o Connection Method Use professional wire nuts or other safe, long- term connectors that are appropriate for the
installation conditions and that are sized properly for wire gauge(s) and number of wires to be connected for the
together in the connector.
Important: Cut off all unused wires in a way that ensures that none of them will short to any of the
other wires.
Δ Code Requirements -- Typical wiring entails - -protected connections inside installer provided water
proof junction box, with cable entering junction box via water-tight fitting that is sized appropriately for
wire jacket diameter (see However, always wire in accordance with code requirements. below).
CABLE
BASE PLATE with TABS 4 x EDGE
CABINET
PORT CAP
PORT
HANDLES (x2)
o Color Connection Code
Low- Impedance (6, for GSB8 and GSB12)
Black N (- P = egative ) and Red = ositive (+)
High-Impedance (70V or 100V distributed systems):
Wiring Charts:
GSB8
Cable Wire Color
↓ Ω -For Low Z Input (6 )
Blue
N/C
Black
From Amp – (negative)
Black with White Stripe
N/C
Gray
N/C
Green
N/C
Yellow
N/C
Red
From Amp + (positive)
N/C = No Connection. Cut, insulate and tie
GSB12
Cable Wire Color
↓ Ω For -Low Z Input (6 )
Blue
N/C
Black
From Amp – (negative)
Black with White Stripe
N/C
Gray
N/C
Green
N/C
Yellow
N/C
Red
From Amp + (positive)
N/C = No Connection. Cut, insulate and tie
Instructions:
o For high- impedance systems (70V/100V), tie together Blue and Black and insulate
this connection.
o Common (negative from amplifier) = Black with white stripe
o GSB8 -- Positive (positive from amplifier):
Gray = 25W @ 70V or 50W @ 100V
Green = 50W @ 70V or 1 00W @100V
Yellow = 100W @ 70V ( )N/C at 100V
o GSB12 -- Positive (positive from amplifier):
Gray = 50W @ 70V or 100W @ 100V
Green = 100W @ 70V or 200W @100V
Yellow = 200W @ 70V (N/C at 100V)
o Wire Gauge – 4 The wire gauge is 1 AWG (approx. 1.6 mm2) , UL1569. The cable jacket diameter is 11 mm (0.43 in.).
BASE PLATE
The GSB subwoofer can be installed either with or without the included BASE PLATE. Even though the speaker typically gets
installed into BASE the ground, the PLATE provides additional EDGE TABS that can provide added security and stability. The tabs
make it more difficult to pull the subwoofer out of the ground. In addition, the 8.5 mm (0.32 in) diameter eachhole in s EDGE TAB
can be used for that bolts or stakes to further secure the subwoofer in place (for example, securing via bolts onto a concrete block
may get installed below the subwoofer).
Installation Onto a Deck the most for this subwoofer, it can be While installation into the ground is typical installation method
mounted onto a deck or other horizontal surface by attaching the BASE PLATE to the bottom of the CABINET and using the holes in
each EDGE TAB for securing hardware.
To attach the BASE, use the included and 8 pcs of drive bolts (SUS304 material) - -4 mm x 20 mm flat head Phillips through the base
into the 8 threaded cabinet.inserts located on the bottom of the
8 BOLTS:
4 mm x 20 mm F -H lat ead Phillips

Especificaciones del producto

Marca: JBL
Categoría: Vocero
Modelo: GSB8

¿Necesitas ayuda?

Si necesitas ayuda con JBL GSB8 haz una pregunta a continuación y otros usuarios te responderán




Vocero JBL Manuales

Vocero Manuales

Últimos Vocero Manuales