Jung LS5232MS Manual de Usario

Jung No categorizado LS5232MS

Lee a continuación 📖 el manual en español para Jung LS5232MS (4 páginas) en la categoría No categorizado. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

Centre plate with memory function and sensor connection

Blinds Management

Centre plate with memory function and sensor connection

Art. No. : ..5232 MS..

Operating instructions

1 Safety instructions

Electrical equipment may only be installed and fitted by electrically skilled persons.

Serious injuries, fire or property damage possible. Please read and follow manual fully.

Danger of electric shock. Always disconnect before carrying out work on the devise or

load. At the same time, take into account all circuit breakers that supply dangerous

voltage to the device or load.

Danger of electric shock. Device is not suitable for disconnection from supply voltage.

These instructions are an integral part of the product, and must remain with the end

customer.

2 Device components

Figure 1: Device components

(1) Venetian blind control

(2) Frame

(3) Cover

3 Function

Intended use

- Operation of electrically-driven blinds and shutters

- Operation on control of the Venetian blind control system

Product characteristics

- One Up and Down travelling time can be saved respectively for daily execution

- Buzzer for signalling

- Evaluation of a sun sensor

- Brightness threshold 20,000 lx

1/4

32518613

J:0082518613 20.05.2014

Operating modes

Memory mode:

- The saved Up and Down travelling times are executed in a 24-hour cycle.

- A signal tone sounds when the button is pressed.

i No signal tone sounds when activating via an extension.

Push-button mode:

- The saved travelling times are not executed.

- No signal tone sounds when the button is pressed.

Sun protection function

The connection of a sun sensor enables automatic shading when it is very bright outside. If the

measured brightness exceeds the brightness threshold for more than 2 minutes, the blind

moves downwards and stops as soon as the sun sensor is shaded.

i The sun protection function is only activated if the Venetian blind has been moved to the

upper end position and the control has deactivated automatically after 2 minutes. Each

manual operation deactivates the sun protection.

If the brightness threshold is fallen short of for more than 15 minutes, the Venetian blind moves

back to the upper end position.

Behaviour after a mains voltage failure

- A mains voltage failure that lasts less than 30 minutes causes the saved travelling times to

be delayed by the duration of the power failure.

- After a mains voltage failure lasting longer than 30 minutes, both saved travelling times are

deleted. After mains voltage return, the memory mode is active.

4 Operation

Moving the Venetian blind

o Press top or bottom of cover for one to 3.5 seconds.

The Venetian blind moves in the desired direction to the end position or stops when the

button is pressed again.

Adjusting the slats

o Press top or bottom of cover for shorter than one second.

The slat position changes in the desired direction for as long as the button is pressed.

Changing operating mode

o Press top or bottom of cover for 8 to 12 seconds.

After 2 seconds, several short signal tones are sounded and a long continuous tone of

1.5 seconds.

After a further 3 seconds, the operating mode switches over and the new operating mode

is signalled:

4 short signal tones = memory mode

1-second continuous tone = push-button mode

Saving travelling times

The travelling times can be saved in push-button mode or memory mode. Only the current time

can ever be saved as travelling time

o Press top of cover for 3.5 to 8 seconds to save the Up travelling time or press bottom of

cover to save the Down travelling time.

After 2 seconds, several short signal tones are sounded and a long continuous tone of

1.5 seconds.

Once the continuous tone begins, the travelling time is saved. Any existing value will be

overwritten.

i It is also possible to only save an Up or Down travelling time.

2/4

32518613

J:0082518613 20.05.2014

Blinds Management

Centre plate with memory function and sensor connection

Deleting all travelling times

o Press top or bottom of cover for longer than 12 seconds.

After 2 seconds, several short signal tones are sounded and a long continuous tone of

1.5 seconds.

Then the operating mode is signalled.

After about 12 seconds, a 3-second long continuous tone begins.

Once the continuous tone begins, the travelling times are deleted and the cover is in

memory mode.

5 Information for electrically skilled persons

5.1 Fitting and electrical connection

Mounting and connecting

DANGER!

Electrical shock when live parts are touched.

Electrical shocks can be fatal.

Before carrying out work on the device or load, disengage all the

corresponding circuit breakers. Cover up live parts in the working environment.

The Venetian blind control is mounted and connected properly (see instructions for the relevant

Venetian blind control).

o If necessary, install sun sensor and connect to terminal block (see instructions for the

sensors and control).

i Connect the sun sensor with the correct polarity. If a sensor is connected with reversed

polarity, this will result in malfunctions. It might not be possible to operate the cover any

more.

o Mount cover (3) with frame (2) onto the Venetian blind control (1) (figure 1).

6 Appendix

6.1 Technical data

Ambient temperature 0 ... +45 °C

Storage/transport temperature -10 ... +60 °C

Switch-over time for direction change approx. 1 s

Moving time approx. 120 s

Data according to EN 60730-1

Action 1.B

Degree of soiling 2

Meas. surge vol. 4000 V

SELV limit value DC 12 V

6.2 Accessories

Sunlight / dawn sensor Art. No. 32 SD

Extension flex Art. No. 32 K

6.3 Warranty

We reserve the right to make technical and formal changes to the product in the interest of

technical progress.

We provide a warranty as provided for by law.

Please send the device with a description of the defect to our central customer service office.

3/4

32518613

J:0082518613 20.05.2014

Blinds Management

Centre plate with memory function and sensor connection

Especificaciones del producto

Marca:	Jung
Categoría:	No categorizado
Modelo:	LS5232MS
Tipo de operación:	Draaiknop
parrilla eléctrica:	1500 W
Color del producto:	Wit
Pantalla incorporada:	Nee
Peso.:	46500 g
Ancho:	595 mm
Profundidad:	600 mm
Altura:	900 mm
Parrilla:	Ja
Bloqueo infantil:	Ja
Clase-de-eficiencia-energética:	A
tipo de reloj:	Elektronisch
cocinar al vapor:	Ja
Altura (mín.):	850 mm
Potencia quemador/zona de cocción 2:	1200 W
Potencia quemador/zona de cocción 3:	1800 W
Potencia quemador/zona de cocción 1:	2300 W
Número de quemadores/zonas de cocción:	4 zone(s)
tipo de placa:	Inductiekookplaat zones
Fuente de energía del horno:	Electrisch
Número de hornos:	1
Número de zonas de cocción electrónicas:	4 zone(s)
Posición de control:	Voorkant
Consumo de energía (convencional):	0.99 kWu
Consumo de energía (convección forzada):	0.83 kWu
Tamaño del horno:	Groot
Horno de capacidad neta:	77 l
Mango de color:	Zwart
Indicador de calor residual:	Ja
Número de parrillas del horno:	1
Función de pizza:	Ja
Potencia quemador/zona de cocción 4:	1200 W
Fuente de alimentación quemador/zona de cocción 1:	Electrisch
Fuente de alimentación quemador/zona de cocción 2:	Electrisch
Fuente de alimentación quemador/zona de cocción 3:	Electrisch
Fuente de alimentación del quemador/zona de cocción 4:	Electrisch
Potencia del horno:	9700 W
Posición del quemador/zona de cocción 1:	Links voor
Diámetro quemador/zona de cocción 1:	210 mm
Posición quemador/zona de cocción 2:	Links achter
Quemador/zona de cocción diámetro 2:	145 mm
Posición quemador/zona de cocción 3:	Rechts achter
Quemador/zona de cocción diámetro 3:	180 mm
Posición del quemador/zona de cocción 4:	Rechts voor
Quemador/zona de cocción diámetro 4:	145 mm
voltaje-de-entrada-de-CA:	230 V
Tipo-producto:	Vrijstaand fornuis
Ruedas traseras:	Ja