Kathrein AVH 06 Manual de Usario

Kathrein No categorizado AVH 06

Lee a continuación 📖 el manual en español para Kathrein AVH 06 (4 páginas) en la categoría No categorizado. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/4
1 / 4
AVH 06 207500001
Band III TV antenna, suitable for DAB+
Features
•Outdoor antenna
•Suiable for DAB+
•Suitable for vertical (pre-installed) and horizontal polarization
•Easy installation
About This Manual
This document is part of the product and describes how to
install and connect the AVH 06 Band III TV antenna.
►Do not install or use the device until you have read and
understood this document.
►Keep this document for reference throughout the service life
of the device and pass it on to any new owner or user.
For the most up-to-date version of this document, go to
www.kathrein-ds.com
Scope of delivery
•Band III TV antenna AVH 06
•F-type screw-on connector for cable LCD 90/111 A+/115 A+/120 A+/130 A+, KEC 120 A+
•Weather protection sleeve
•Instructions for use
Transport and Storage
►Use the original packaging for transporting the device.
►Store the antenna in a dry place and protect it from mechanical damage.
Intended use
The AVH 06 is a Band III TV antenna. The antenna is solely designed for the limited purpose of receiving terrestrial TV and DAB+
signals and as indoor antennas. Under the terms of DIN 4131, an indoor antenna is defi ned as an antenna if the mast length does not
exceed 6 meters and if its fi xed end moment is at 1,650 Nm maximum. Any other use or non-observance of these instructions und
der den Geräten beiliegenden Dokumentation will result in the loss of the warranty and guarantee. The following circumstances lead
to the loss of warranty and liability claims against the manufacturer:
►Improper installation
►Use of unlisted fi xing material, which means that mechanical safety cannot be guaranteed
►Structural changes or interventions in the antenna, which can endanger both the mechanical and electrical as well as the func-
tional safety
►disregarding the assembly and safety instructions in this manual
Safety Instructions
ATTENTION! DANGER FOR LIFE!
Do not under any circumstances mount an antenna under power lines. Touching power supply lines with parts of your
body, with antenna parts or tools may cause an electrical shock or serious burns.
Ground the antenna installation according to DIN EN 60728-11!
2 / 4
Please read the following safety instructions carefully and thoroughly before you start installing the antenna, and keep
observing them during the installation!
The installation of the antenna demands a high degree of responsability for yourself and other people. For this reason, the instal-
lation must be executed by an electrician (expert in his/her trade). In order to assist you, some important safety instructions have
been compiled in the following. However, these instructions are not exhaustive, as p2-we are not aware of the local conditions.
►Do not use the antenna for purposes other than intended by the manufacturer.
►Only use the components as prescribed by the manufacturer and do not modify them.
►When selecting the antenna site, take account of the building‘s structural characteristics. Installation on the edge of
cylindrical structures could lead to increased wind loads and vibration stress according to DIN 1055, part 4, DIN 4131.
Non-observance of these instructions may cause exceeding of the load limit or the vibration resistance.
►Do not mount the antenna on buildings with rooftops made of easily infl ammable materials (e.g. straw, reed or
similar materials).
►Only step on fi rm, dry rooftops and protect yourself against falling down
►To ensure safety, ladders, sca oldings, safety belts etc. must be in good structural order.
►Passers-by must not be endangered by falling objects. Secure the work/danger area!
►Ensure that the technical values (e.g. wind load) of the antenna mast are not exceed. Consult the manufacturer
if you do not know these values. See for an overview of the masts o ered by „Suitable Kathrein masts“ on page 4
KATHREIN Digital Systems.
►Mount the antenna mast on solid ground only (walls, concrete, rafters) using the clamps, dowels and screws recom-
mended by the manufacturer
►Immediately leave the roof in case of a thunderstorm!
Mast installation and mast calculation
•Make sure masts is in vertical position when installing it
•Only use masts or standpipes specially designed for antenna
installation. Other tubes mostly do not have the necessary
stability to withstand heavy wind or other climatical situations.
Kathrein masts and clamps fulfi ll these requirements. See
„Suitable Kathrein masts“ on page 4 for an overview of the
masts o ered by KATHREIN Digital Systems.
•The clamping range of the AVH 06 masting clamps is 22 to
55 mm
•If the mast is to be mounted on a roof, at least 1/6 of its length
must be clamped
•Make sure that the mast holders (e.g. clamps) are mounted on
solid ground (wood, concrete, walls)
Never exceed the maximum load capacity of the
mast or clamps when mounting several antennas
on the mast.
The bending moment a ects the mast on the
upper attachment point for all antennas. The wind
load on the mast must be included in the calcula-
tion.
The overall bending moment is not to exceed the
maximum permitted bending moment of the mast
and must not be greater than 1,650 Nm. If the
bending moment is greater, a static engineer is
required to provide verifi cation of the transfer of
forces into the structure of the building.
CAS 80gr
SAT antenna
Olympia 150
AVH 06
ABA 20
Mast ZSH 59
AOP 65
1138 Nm
25 N x 4,0 m = 100 Nm
33 N x 3,6 m = 119 Nm
103 N x 2,8 m = 289 Nm
450 N x 1,4 m = 630 Nm
1,4 m
(Middle of the reflector)
1,0 m
2,8 m
3,6 m
4,0 m
According to EN 60728-11, the fixing range
of the antenna mast be at least 1/6
of the total mast length.
M = W x a + W x a + W x a + ...
b
1
1
2
2
3
3
= Bending moment
= Given windload in catalogue
= Mast length from the antenna to
the mast fixing point
M
W
a
b
1,2,3
1,2,3
3 / 4
Antenna installation
1. Unpacking the antenna
2. Turn the rods by 90°, push them in the middle (observe
marking) and tighten the screws
3. Dipole mounting (Position according to picture)
4. Connect the cable to the F-socket, put the weather
protection sleeve on
The antenna can also be mounted horizontally. For this purpose the mast clamp must be turned by 90°.

Especificaciones del producto

Marca: Kathrein
Categoría: No categorizado
Modelo: AVH 06

¿Necesitas ayuda?

Si necesitas ayuda con Kathrein AVH 06 haz una pregunta a continuación y otros usuarios te responderán


No categorizado Kathrein Manuales

Kathrein

Kathrein FMK 100b Manual de Usario

19 Octubre 2024
Kathrein

Kathrein CAP 500M plus Manual de Usario

15 Octubre 2024
Kathrein

Kathrein HDM 135 Manual de Usario

4 Octubre 2024
Kathrein

Kathrein FRM 100 Manual de Usario

30 Septiembre 2024
Kathrein

Kathrein UFO 83 Manual de Usario

28 Septiembre 2024
Kathrein

Kathrein CAP Converter V2 Manual de Usario

22 Septiembre 2024
Kathrein

Kathrein FAS 100 Manual de Usario

21 Septiembre 2024
Kathrein

Kathrein BZD 30 Manual de Usario

20 Septiembre 2024
Kathrein

Kathrein UFO 80 Manual de Usario

19 Septiembre 2024
Kathrein

Kathrein OSC 100 micro Manual de Usario

17 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024