Kemppi A7 TIG Orbital System 300 Manual de Usario
Kemppi
Dispositivo de soldadura
A7 TIG Orbital System 300
Lee a continuación 📖 el manual en español para Kemppi A7 TIG Orbital System 300 (61 páginas) en la categoría Dispositivo de soldadura. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/61
300
1920390
1615
A7 TIG Orbital System
EN
OPERATING MANUAL
2A7 TIG Orbital System 300© Kemppi Oy 2016 1615
OPERATING MANUAL
CONTENTS
1. Introduction ..........................................................................................4
1.1 General ......................................................................................................4
1.2 About the product ....................................................................................5
1.3 Weld head .................................................................................................. 6
1.3.1 General specications .............................................................................6
1.4 Controller unit ...........................................................................................7
1.4.1 Remote control ......................................................................................7
1.5 Compatibility .............................................................................................8
2. Installation .............................................................................................9
2.1 Controller connections .............................................................................9
2.2 Water cooler ............................................................................................10
2.2.1 Filling water cooler with coolant ............................................................10
2.2.2 Operating the water ow .......................................................................10
2.3 Weld head set-up ....................................................................................11
2.3.1 Assemblies ..........................................................................................11
2.4 Installing guide ring on tube ..................................................................13
2.5 Mounting the weld head ........................................................................14
2.6 Wire spool ................................................................................................15
2.7 Electrode ..................................................................................................16
2.8 Torch centering .......................................................................................17
2.9 Mechanical adjustments .........................................................................17
3. Operation .............................................................................................18
3.1 Welding settings .....................................................................................18
3.1.1 Setting current level ..............................................................................18
3.1.2 Pulsillation (synchronized pulsed current/oscillation mode)..........................18
3.1.3 Filler wire speed ...................................................................................18
3.1.4 Root-pass procedure .............................................................................19
3.1.5 Hot-pass procedure ..............................................................................19
3.1.6 Fill passes, oscillation (weave), and stringer bead techniques ........................20
3.1.7 Shield gas eects ..................................................................................21
3.2 Preparing the work piece ........................................................................21
3.2.1 Groove preparation ...............................................................................21
3.2.2 Joint design and t-up tolerance ............................................................21
3.2.3 Other preparations ...............................................................................22
3.2.4 Developing weld procedures/process parameters ......................................22
3.3 Controller unit menus .............................................................................23
3.3.1 Main Menu ..........................................................................................23
3.3.2 Maintenance Menu ...............................................................................25
3.3.3 Options Menu ......................................................................................27
3.3.4 Compatible weld head models ................................................................28
3.3.5 Calibrate head .....................................................................................28
3.3.6 300-head guide ring speed factors ...........................................................29
3.3.7 Advanced Help ....................................................................................30
3.3.8 Autotack .............................................................................................30
3.3.9 Autoprogram .......................................................................................31
3.4 Alphanumeric labelling ...........................................................................33
3.5 Manual programming .............................................................................33
3.6 Prepurge – Upslope.................................................................................37
3.7 Programmed oscillation width (without striking an arc) .......................37
3.8 Editing a weld program...........................................................................38
3.9 Completing the programming ...............................................................39
3.10 Updating software ..................................................................................39
3.11 Welding ...................................................................................................39
3.12 Travel speed correction ...........................................................................39
3.13 Shielding gas ...........................................................................................40
3.13.1 Purging the pipe ID with inert gas ...........................................................41
4. Additional details ..............................................................................42
4.1 Controller technical data .........................................................................42
4.2 Weld head technical data........................................................................42
4.3 Ordering information ..............................................................................43
3A7 TIG Orbital System 300© Kemppi Oy 2016 1615
OPERATING MANUAL
5. Troubleshooting ................................................................................46
5.1 Operation problems ................................................................................46
5.2 Root-pass renement for horizontal pipe (5G position) ........................47
5.3 Common weld defects: identication and prevention ..........................48
5.4 Warnings/error messages ......................................................................49
5.5 Checking machine setup during booting ..............................................53
5.6 Machine system messages......................................................................54
5.7 Controller unit fault conditions ..............................................................54
6. Maintenance .......................................................................................55
6.1 Preventing tungsten electrode rotation not concentric to tube OD .....55
6.2 Periodic maintenance .............................................................................55
6.3 Weld head maintenance .........................................................................56
6.3.1 External maintenance............................................................................56
6.3.2 Low prole kit installation ......................................................................56
6.3.3 Torch cable replacement ........................................................................56
6.3.4 Maintenance of the wire feed nozzle ........................................................56
6.3.5 Water cooler maintenance/ushing procedure for the torch cable .................57
6.3.6 Maintenance of torch components ..........................................................57
6.3.7 Cleaning the weld head .........................................................................58
6.3.8 Internal arcing .....................................................................................58
6.4 Printer operation and maintenance .......................................................59
6.4.1 Installing paper in the printer..................................................................59
6.4.2 Cleaning the printer ..............................................................................59
6.5 Service Workshop maintenance ............................................................59
7. Disposal ................................................................................................60
Especificaciones del producto
| Marca: | Kemppi |
| Categoría: | Dispositivo de soldadura |
| Modelo: | A7 TIG Orbital System 300 |
¿Necesitas ayuda?
Si necesitas ayuda con Kemppi A7 TIG Orbital System 300 haz una pregunta a continuación y otros usuarios te responderán
Dispositivo de soldadura Kemppi Manuales
5 Octubre 2024
22 Septiembre 2024
22 Septiembre 2024
21 Septiembre 2024
21 Septiembre 2024
20 Septiembre 2024
19 Septiembre 2024
17 Septiembre 2024
13 Agosto 2024
12 Agosto 2024
Dispositivo de soldadura Manuales
- Dispositivo de soldadura Weldkar
- Dispositivo de soldadura Frilass
- Dispositivo de soldadura Elektra Beckum
Últimos Dispositivo de soldadura Manuales
17 Septiembre 2024
3 Septiembre 2024
3 Septiembre 2024
2 Septiembre 2024
29 Agosto 2024