Kicker CX660.5 Manual de Usario

Kicker receptor CX660.5

Lee a continuación 📖 el manual en español para Kicker CX660.5 (32 páginas) en la categoría receptor. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/32
CX
AMPLIFIERS
Owner’s Manual
CXA660.5
Manual del Propietario | Español
AMPLIFICADOR DEL LA SERIE CX.5
Benutzerhandbuch | Deutsch
VERSTÄRKER DER CX.5-SERIE
Manuel d’utilisation | Française
AMPLIFICATEUR DE SÉRIE CX.5
2
CX.5-SERIES AMPLIFIERS
OWNER’S MANUAL
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Serial Number:
Model: CXA660.5
RMS Power, and AMP1 AMP2
@ 14.4V, 4Ω stereo, 1% THD+N
@ 14.4V, 2Ω stereo, 1% THD+N
@ 14.4V, 4Ω mono, 1% THD+N
65W x 4
90W x 4
180W x 2
RMS Power, channelSUB
@ 14.4V, 4Ω mono, 1.5 % THD+N
@ 14.4V, 2Ω mono, 1.5 % THD+N
150W x 1
300W x 1
Length [in, cm] 14, 30
Height [in, cm] 2-3/8, 5.9
Width [in, cm] 6-3/4, 17
Frequency Response [Hz] 10–20kAMPS 1-2:
SUB: 25–200
Signal-to-Noise Ratio [dB] >90dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mV–5V
High Level: 1V–40V
Selectable Electronic Crossover HI or OFF; Variable 10–200Hz @ 12dB/OctaveAMPS 1-2:
SUB: LO; 50–200Hz @ 12dB/Octave
KickEQBass Boost Variable 06dB @ 40Hz
Subsonic Filter 24dB/Octave, Fixed @ 25HzSUB:
Remote Bass: Yes [sold separately]
Pro Tip: To get the best performance from your new KICKER Amplifi er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
MODEL: CXA660.5
WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing! Turning up a
system to a level that has audible distortion is more damaging to your ears than listening to an undistorted system at the same
volume level. The threshold of pain is always an indicator that the sound level is too loud and may permanently damage your
hearing. Please use common sense when controlling volume.
3
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open
ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger compartment. Drill
four holes using a 7/64 (3mm) bit and use the supplied #8 screws to mount the amplifi er.
The KICKER CX Amplifi ers are capable of space-saving vertical mounting. Use a 2.5mm hex key (Allen wrench)
to loosen the endpanel, remove the existing brackets, then insert and tighten the double-slotted brackets to the
amplifi er as illustrated.
double-slotted
bracket
hex screws
amplifi er side panel
VERTICAL MOUNTING
Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the
amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the
batterys negative post and the vehicle chassis is recommended.
The CX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereos source unit. A high-level signal can be run from the source unit’s speaker outputs to the
stereo RCA input on the end panel of the amplifi er using the KICKER KISL as shown (make sure you set the CX
amplifi ers input level switch to “HI”). Alternatively, the signal can be delivered to the amplifi er using the low-level
RCA outputs on the source unit; set the input level switch on the end panel of the amplifi er to “LO”. Keep the
audio signal cable away from factory wiring harnesses and other power wiring. If you need to cross this wiring,
cross it at a 90 degree angle.

Especificaciones del producto

Marca: Kicker
Categoría: receptor
Modelo: CX660.5

¿Necesitas ayuda?

Si necesitas ayuda con Kicker CX660.5 haz una pregunta a continuación y otros usuarios te responderán




receptor Kicker Manuales

receptor Manuales

Últimos receptor Manuales