Kicker CX800.1 Manual de Usario

Kicker receptor CX800.1

Lee a continuación 📖 el manual en español para Kicker CX800.1 (28 páginas) en la categoría receptor. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/28
CX
AMPLIFIERS
Owner’s Manual
CXA400.1 | CXA800.1
CXA1200.1 | CXA1800.1
Manual del Propietario | Español
AMPLIFICADOR DEL LA SERIE CX.1
Benutzerhandbuch | Deutsch
MONOVERSTÄRKER DER CX.1-SERIE
Manuel d’utilisation | Française
AMPLIFICATEUR DE SÉRIE CX.1
2019 CXA Mono Amps Rev H.indd 1
2019 CXA Mono Amps Rev H.indd 1
2019 CXA Mono Amps Rev H.indd 1
2019 CXA Mono Amps Rev H.indd 1
2019 CXA Mono Amps Rev H.indd 1 10/7/2019 2:33:32 PM
10/7/2019 2:33:32 PM
10/7/2019 2:33:32 PM
10/7/2019 2:33:32 PM
10/7/2019 2:33:32 PM
2
CX.1-SERIES AMPLIFIERS
OWNER’S MANUAL
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open
ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger compartment. Drill
four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifi er.
The KICKER CX Amplifi ers are capable of space-saving vertical mounting. Use a 2.5mm hex key (Allen wrench)
to loosen the end panel, remove the existing brackets, then insert and tighten the double-slotted brackets to the
amplifi er as illustrated on the next page.
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Model Number:
Serial Number:
MODEL: CXA400.1 | CXA800.1
CXA1200.1 | CXA1800.1
Model: CXA400.1 CXA800.1 CXA1200.1 CXA1800.1
RMS Power [Watts]
@ 14.4V, 4 mono, 1% THD+N
@ 14.4V, 2 mono, 1% THD+N
@ 14.4V, 1Ω mono, 1% THD+N
150W x 1
300W x 1
400W x 1
300W x 1
600W x 1
800W x 1
600W x 1
1200W x 1
1200W x 1
900W x 1
1800W x 1
1800W x 1
Length [in, cm] 8-1/8, 20.6 8-1/8, 20.6 12, 30.6 13-5/8, 34.6
Speci cations common to all models:
Height [in, cm] 2-3/8, 5.9
Width [in, cm] 6-3/4, 17
Frequency Response [Hz] 25–200
Signal-to-Noise Ratio [dB] >95, A-weighted, re: rated power
Input Sensitivity Low Level: 125mV–5V
High Level: 1V–40V
Electronic Crossover Variable Lo-pass 50Hz–200Hz, 12dB/octave
KickEQ™ Bass Boost Variable 0–6dB @ 40Hz
Subsonic Filter 25Hz, 24dB/octave
Remote Bass Yes (sold separately)
WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing! Turning up a
system to a level that has audible distortion is more damaging to your ears than listening to an undistorted system at the same
volume level. The threshold of pain is always an indicator that the sound level is too loud and may permanently damage your
hearing. Please use common sense when controlling volume.
Pro Tip: To get the best performance from your new KICKER Amplifi er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
NOTE: 2019 CXA mono amplifi ers are stable - power rating +/- 10%.
2019 CXA Mono Amps Rev H.indd 2
2019 CXA Mono Amps Rev H.indd 2
2019 CXA Mono Amps Rev H.indd 2
2019 CXA Mono Amps Rev H.indd 2
2019 CXA Mono Amps Rev H.indd 2 10/7/2019 2:33:34 PM
10/7/2019 2:33:34 PM
10/7/2019 2:33:34 PM
10/7/2019 2:33:34 PM
10/7/2019 2:33:34 PM
3
Wiring: Disconnect the vehicles battery to avoid an electrical short. Then, connect the ground wire to the
amplifi er. Make the ground wire short, 24(60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the
batterys negative post and the vehicle chassis is recommended.
The CX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereos source unit. A high-level signal can be run from the source unit’s speaker outputs to the
stereo RCA input on the end panel of the amplifi er using the KICKER KISL as shown (make sure you set the CX
amplifi er’s input level switch to “HI”). Alternatively, the signal can be delivered to the amplifi er using the low-level
RCA outputs on the source unit. Set the input level switch on the end panel of the amplifi er to “LO”. Either input
method will provide an output signal at the RCA output, which effectively passes the audio signal to another
amplifi er or component. Keep the audio signal cable away from factory wiring harnesses and other power wiring.
If you need to cross this wiring, cross it at a 90 degree angle.
source unit
high-level speaker
outputs
to amplifi er
shield
double-slotted
bracket
+
core conductor
OR
VERTICAL MOUNTING
hex screws
amplifi er end panel
KICKER KISL (optional)
from source unit high-
level speaker outputs
to amplifi er
Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your amplifi er. If you
ever need to remove the amplifi er from the vehicle after it has been installed, the ground wire should be the last
wire disconnected from the amplifi er--just the opposite as when you installed it.
2019 CXA Mono Amps Rev H.indd 3
2019 CXA Mono Amps Rev H.indd 3
2019 CXA Mono Amps Rev H.indd 3
2019 CXA Mono Amps Rev H.indd 3
2019 CXA Mono Amps Rev H.indd 3 10/7/2019 2:33:34 PM
10/7/2019 2:33:34 PM
10/7/2019 2:33:34 PM
10/7/2019 2:33:34 PM
10/7/2019 2:33:34 PM

Especificaciones del producto

Marca: Kicker
Categoría: receptor
Modelo: CX800.1

¿Necesitas ayuda?

Si necesitas ayuda con Kicker CX800.1 haz una pregunta a continuación y otros usuarios te responderán




receptor Kicker Manuales

receptor Manuales

Últimos receptor Manuales