King WHF2420-W Manual de Usario

King Calentador WHF2420-W

Lee a continuación 📖 el manual en español para King WHF2420-W (4 páginas) en la categoría Calentador. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

1. Read all instructions before wiring or using this

heater.

2. WARNING: This heater is hot when in use. To

avoid burns, do not let bare skin touch hot sur-

faces. Keep combustible materials, such as furni-

ture, pillows, bedding, papers, clothes, boxes,

etc., and curtains at least 3ft (.9 m) from the

front of the heater and keep them away from the

sides and rear.

3. CAUTION: Extreme caution is necessary when

any heater is used by or near children or invalids

and whenever the heater is left operating and

unattended.

4. Do not operate any heater after it malfunctions.

Disconnect power at service panel and have

heater inspected by qualified electrician for re-

pair before reusing.

5. Do not use outdoors.

6. WARNING: To disconnect heater,

turn controls to OFF, and turn

OFF power to heater circuit at

IMPORTANT INSTRUCTIONS

ELECTRIC SHOCK OR FIRE HAZARD

DANGER

! !

WARNING

! !

Read Carefully -These instructions are written in an effort to prevent potential difficulties that might arise during

installation. Studying the instructions first may save you considerable time and money later. Observing the following

procedures will keep installation time to a minimum. . Save these instructions for future use

Covers all WHF Series models

WHF Fan Force

Electric Space Heater

King Electrical Mfg. Co. 9131 10th Ave So. Seattle, WA 98108 206- -0400 www.king-electric.com 762

IMPORTANT INSTRUCTIONS

When using electrical heating appliances, basic precautions should always be followed to

reduce the risk of fire, electric shock and injury to persons, including the following:

main disconnect panel.

7. WARNING: Do not insert or allow foreign objects

to enter any ventilation or exhaust opening as this

may cause an electric shock, fire, or damage to

the heater.

8. To prevent a possible of fire, do not block air in-

takes or exhaust in any manner.

9. A heater has hot and arching or sparking parts

inside. Do not use it in areas where gasoline,

paint, or flammable vapors or liquids are used or

stored.

10. WARNING: Use this heater only as described in this

manual. Any other use is not recommended by the

manufacturer and may cause fire, electric shock,

explosion or injury to people and or property.

SAVE THESE INSTRUCTIONS

Figure 1

Figure 2

ELECTRIC SHOCK OR FIRE HAZARD

! !

Figure 3

WHF INSTALLATION INSTRUCTIONS

CAUTION!

Turn OFF all electrical power

to install heater

Rating Label Location

Total Amps Minimum AWG. Wire

Size (Copper Circuit Breaker or

Fuse Size

0 thru 12 #14 15 amp

12.1 thru 16 #12 20 amp

16.1 thru 24 #10 30 amp

Minimum Clearances for heater: Table 1

Front TOP BOTTOM SIDES

36 in 12 in 4 in 6 in

0.9 m 30.5 cm 10.2 cm 15.2 cm

Selecting A Location For Your Heater:

DO NOT install less than 6” (15cm) from vertical side

walls or open edge of door. This heater must have an

unrestricted airflow. DO NOT select a location where it

is likely to be blocked by furniture, curtains, etc. Be

sure the location selected allows sufficient space for the

heater as shown by Table 1. DO NOT locate this heater

in an area where combustible vapors, gases liquids, or

excessive lint, dust or moisture is present.

The wire and breaker sizing chart will give a general rule

of installation size. Consult an electrician if you are not

knowledgeable about wiring codes.

Wire and Breaker Sizing: Table 2

WIRING: Branch Circuit Connection

1. Connect heater only to the voltage, amperage and

frequency specified on the nameplate.

2. Wiring procedures and connections shall be in ac-

cordance with all National and local codes having

jurisdiction.

3. Set the bag containing the grille and packet with

two (2) grille screws aside.

4. Loosen mounting screw and remove fan heater as-

sembly.

5. A knockout of 1/2 inch conduit size (7/8 inch /

2.2cm) is provided in the back and side of the heater

for power to enter. Provide proper strain relief con-

nectors for your wire entering the wallbox.

6. Install wallbox a minimum of 6” from vertical side-

walls and 4” above floor. The front edge of wall

can MUST extend 1/2” beyond finished wall sur-

face.

7. Secure wallbox to the 2 x 4 studs using the two (2)

holes on the side of the wallbox. Secure to wall stud

on opposite side if required.

8. Connect supply wires, attach ground feed wire to

the green ground wire with wire nuts.

9. Reinstall heater assembly into wallbox with screw at

top of interior.

10. Install grille securely with screws provided in pack-

et. Do not over tighten.

11. Test unit by turning thermostat up past room tem-

perature. You will see a puff of smoke as the ele-

ments are energized and the fan turns on. This is a

normal burn off of manufacturing lubricants and will

dissipate in 5 minutes.

12. Heater will continue to run until the room tempera-

ture you set is reached and then turn itself off until

the temperature drops again.

CAUTION - High temperature. Risk of fire, keep electri-

cal cords, drapery, furnishings, and other combusti-

bles at least 3 feet (0.9 m) from the front of the

heater as well as away from the side and rear. To

reduce the risk of fire, do not store or use gasoline or

other flammable vapors and liquids in the vicinity of the

heater.

Figure 2

Wiring Diagram Figure 5

Zero clearance to insulation.

Figure 4

DANGER

OPERATING INSTRUCTIONS

WHF Series Heater

This heater is equipped with a thermal overload

Smart Limit Protection which disconnects ele-

ments and motor in the event normal operating

temperatures are exceeded. If thermal overload trips

due to abnormal operating temperatures, thermal over-

load shall remain open until manually reset by turning

the heater OFF for fifteen minutes. Inspect for any ob-

jects on or adjacent to the heater that may cause high

temperatures. After inspecting the heater, keep the

power to the heater off for 10 minutes to reset the SLP

thermal protector. If the SLP thermal protector shuts

the heater off again, immediately turn the heater OFF

at the circuit breaker and inspect the heater for possible

fan motor failure or dirt and lint on the heating ele-

ment. Repeat the starting procedure. DO NOT TAMPER

OR REMOVE THIS THIS DEVICE.

General information and Guidelines:

This heater must be properly installed before it is used.

DO NOT tamper with or change the operating of this

heater. All service should be preformed by a authorized

service representative. Only replace components with

King approved replacement parts.

Warning: Clean Heater annually. Wait for heater to

cool before removing grill. Use only a soft brush or vacu-

um on blow to clean heater. Re-attach grill before re-

applying power.

Troubleshooting Table

SYMPTOM PROBLEM SOLUTION

Breaker Trips Short Circuit 1.

2. Overloaded Circuit

3. Improper Voltage

3. Verify the heater voltage matches the supply voltage.

Heater not working 1. No Power

2. Loose Connections

3. Defective Limit

1. Turn Breaker ON, turn thermostat ON, check that the breaker is position

properly on panel bus-bar. A 2-Pole breaker must be connected to both bus-

bars (A&B phase) to produce 240V power.

2. Tighten wire connections.

3. -pass the limit to test. If heater works, replace the limit. By

Heater Smokes 1. Oil on Element

2. Needs Cleaning

1. It is normal for the element to burn off some light finishing oil used in the

manufacturing process when first energized. Open windows and allow room

to vent until it stops, usually within a few minutes.

2. Remove any dust or dirt accumulations.

Room Temperature

does not match

thermostat setting

1. Thermostat affected

by another heat

source.

2. Improper calibration

1. Sunlight or other heat sources can affect the thermostat. Move the thermo

stat to another location or remove the heat source.

2. Remove cover and adjust calibration screw.

Room Temperature

swings from too hot

to too cold

1. Defective or low

quality thermostat

1. Replace with a better quality thermostat. Anticipated thermostats are fair-

ly accurate; an electronic thermostat is best.

SAVE THESE INSTRUCTIONS

Operation:

1. This heater must be properly installed in accordance

with the National Electrical Codes (NEC) & local

electrical codes before it is used.

2. After the electric heater has been completely in-

stalled, all thermostats should be turned to LOW or

NO HEAT. Turn ON breakers, wait 3 to 5 minutes and

check to see that the heaters are not operating. If

operating, disconnect power and check for improper

wiring. If none are operating then turn thermostats

to highest position and wait 3 to 5 minutes. Check to

see that all heaters are operating. Should any not be

operating, disconnect power and check wiring.

3. Allow entire system to operate steadily for 1/2 hour.

This should remove oily residue from manufacturing.

(Some smoking may occur).

4. Select the setting for comfort on all thermostats.

5. A safety limit control is provided to turn off the

heater automatically if it is blocked or otherwise

overheats due to an abnormal condition. DO NOT

bypass or remove this safety device from the electri-

cal circuit-see Warning Figure 3 on page 2. During

normal use, this safety control should not operate. If

you find that this control is operating, make sure the

heater is not being blocked. If it continues to cycle

the heater off, disconnect power to heater and have

it checked and repaired by a qualified electrician.

Especificaciones del producto

Marca:	King
Categoría:	Calentador
Modelo:	WHF2420-W
Colocación del dispositivo:	Ingebouwd
Tipo de operación:	Touch
Color del producto:	Zwart
Peso.:	14000 g
Ancho:	790 mm
Profundidad:	510 mm
Altura:	88 mm
Tipo de material (arriba):	Glaskeramiek
Número de quemadores/zonas de cocción:	3 zone(s)
tipo de placa:	Inductiekookplaat zones
Diámetro del quemador/zona de cocción:	160 mm
Diámetro normal del quemador/zona de cocción:	300 mm
Quemador a fuego lento/zona de cocción:	1400 W
Quemador normal/zona de cocción:	2300 W
Quemador/zona de cocción grande:	4800 W
Actual:	32 A
voltaje-de-entrada-de-CA:	230 V