KitchenAid W10655450 Manual de Usario

KitchenAid campana extractora W10655450

Lee a continuación 📖 el manual en español para KitchenAid W10655450 (4 páginas) en la categoría campana extractora. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

W10758628A

BACKSPLASH

Use & Care / Installation Instructions

PANNEAU ANTI-ÉCLABOUSSURE

Utilisation et entretien / Instructions d’installation

Table of Contents/Table des matieres

INSTALLATION REQUIREMENTS………………………….1 EXIGENCES D’INSTALLATION....………………....……....……............................3

INSTALLATION INSTRUCTIONS……………………………2 INSTRUCTIONS D’INSTALLATION…………………...………...............................4

BACKSPLASH USE & CARE………………………………..2 UTILISATION ET ENTRETIEN DU PANNEAU ANTI-ÉCLABOUSSURE.............4

INSTALLATION REQUIREMENTS

• Level

• Stud Finder

• Phillips Head Screwdriver

Parts Supplied

• Backsplash

• Wall brackets

• Screws, 8-18 x ½”

• Screws, 10-2 x 2”

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided

with any tools listed here.

Tools Required

• Drill

• 1/8” Drill Bit

• Tape Measure

Location Requirements

The backsplash can be installed on the backwall behind a slide-in, commercial style range or cooktop.

Appliance must be level side to side and front to back.

Backsplash Dimensions

A. Backsplash width, 30”

B. Backsplash height, 7 3/8”

INSTALLATION INSTRUCTIONS

Mark Guide Lines

1. Mark a small line on the backwall at the height of the range

or cooktop.

2. Measure 1 3/8” down from this line and draw a level line the

full length of the installation space. This line represents the

bottom edge of backsplash line.

3. Position the bottom edge of the ange along the bottom

edge of backsplash line. Align the center of the backsplash

with the center of the appliance. Mark each mounting hole

(2 locations) with a pencil. Set panel aside.

4. Measure up 6 3/8” from the bottom edge of backsplash

line and draw a level line the full length of the installation

space. This mounting bracket guide line represents where

the mounting brackets will attach to the wall.

Align this surface

with the mounting

bracket guide line

Install Mounting Brackets

1. Usingastudnder,locatetheedgesofthewallstudswithin

the installation space.

2. Mark the center of each stud and draw a line down the center

of the stud.

3. Line up the top of the wall mounting bracket with the mounting

bracket guide line from “Mark Guide Lines” section.

4. Center a bracket along the centerline of each wall stud.

5. Mount each bracket to wall using two 10-12 x 2” screws

per bracket (included with kit). A minimum of two mounting

brackets should be installed for the 30” models.

Install Backsplash

1. HooktheangeonthebackoftheBacksplashoverthemountingbracketsattachedtothewall.

2. Center the Backsplash and align the two holes at the bottom of the Backsplash with the marks on the wall made in

the “Mark Guide Lines” section.

3. Attachbrackettowallusingthetwo10-12x2”screwsthroughtheholesatthebottomoftheange.

BACKSPLASH USE & CARE

General Cleaning

Donotusesoap-lledscouringpads,abrasivecleaners,CooktopPolishingCreme,steel-woolpads,grittywashcloths

or abrasive paper towels. Damage may occur, even with one-time or limited use. Rub in direction of grain to avoid

damaging.

Cleaning Method:

• Affresh® Stainless Steel Cleaner and Polish: Follow the instructions found on the label of the cleaner.

• Liquid detergent or all-purpose cleaner: Rinse with clean water and dry with soft, lint-free cloth.

Center

Line

Mounting Bracket

Guide Line

Bottom Edge of Backsplash

Range/Cooktop

Height

6 3/8”

1 3/8”

W10758628A

PANNEAU ANTI-ÉCLABOUSSURE

Utilisation et entretien / Instructions d’installation

Table des matieres

EXIGENCES D’INSTALLATION....………………....……....……............................3

INSTRUCTIONS D’INSTALLATION…………………...………...............................4

UTILISATION ET ENTRETIEN DU PANNEAU ANTI-ÉCLABOUSSURE.............4

EXIGENCES D’INSTALLATION

• Niveau

• Détecteur de poteaux structuraux

• Tournevis cruciforme Phillips

Pièces fournies

• Panneau anti-éclaboussure

• Supports muraux

• Vis 8-18 x ½”

• Vis 10-2 x 2”

Outils et pièces

Rassembler les outils et composants nécessaires avant d’entreprendre l’installation. Lire et observer les

instructions fournies avec chacun des outils de la liste ci-dessous.

Outillage nécessaire

• Perceuse

• Foret de 1/8”

• Ruban à mesurer

Exigences d’emplacement

Le panneau anti-éclaboussure peut être installé sur le mur du fond, derrière une cuisinière ou une table de

cuisson encastrée de style commercial. L’appareil doit être horizontal dans le sens latéral et en profondeur.

Dimensions du panneau anti-éclaboussure

A. Largeur du panneau, 30”

B. Hauteur du panneau, 7 3/8”

Especificaciones del producto

Marca:	KitchenAid
Categoría:	campana extractora
Modelo:	W10655450
Color del producto:	Wit
Peso.:	326 g
Amable:	Radio-Controlled (RC) Model Parts
Compatibilidad de marca:	E-flite
Compatibilidad:	- Apprentice S 15e RTF\r\n- Apprentice S 15e BNF\r\n- Pulse 15e BNF Basic