Liftmaster 41K4629 Manual de Usario

Liftmaster No categorizado 41K4629

Lee a continuación 📖 el manual en español para Liftmaster 41K4629 (8 páginas) en la categoría No categorizado. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/8

COMMERCIAL PROTECTOR SYSTEM®

INSTALLATION INSTRUCTIONS

To reduce the risk of SERIOUS INJURY or DEATH:

• This device is for use ONLY on LiftMaster® Commercial Door

Operators.

• For INDOOR USE ONLY.

• Disconnect power BEFORE installing the Commercial Protector

System®.

• READ AND FOLLOW ALL INSTRUCTIONS.

Facing the door from inside the garage (installation procedures are the same for all door types).

Left Side of Garage Right Side of Garage

Photoelectric Sensor

Invisible Light Beam

Protection Area

THE COMMERCIAL PROTECTOR SYSTEM®

IMPORTANT INFORMATION ABOUT THE PHOTOELECTRIC SENSORS

Be sure power to the operator is disconnected.

When properly connected and aligned, the photoelectric sensors will detect an obstruction in the path of its invisible light beam. If an

obstruction breaks the light beam while the door is closing, the door will stop and typically reverse to the full open position.

The photoelectric sensors must be installed inside the garage so that the sending and receiving sensors face each other across the door,

no more than 6" (15 cm) above the ﬂ oor. Either can be installed on the left or right of the door as long as the sun never shines directly

into the receiving eye lens. This product is not suitable for outdoor use.

The brackets must be securely fastened to a solid surface such as the wall framing. If installing in masonry construction, add a piece of

wood at each location to avoid drilling extra holes in masonry if repositioning is necessary.

The invisible light beam path must be unobstructed. No part of the garage door (or door tracks, springs, hinges, rollers or other

hardware) may interrupt the beam while the door is closing. If it does, use a piece of wood to build out each sensor mounting location to

the minimum depth required for light beam clearance.

APPLICATION

The Commercial Protector System® (CPS) is suitable for LiftMaster

Commercial Door Operators with a Normally Open (N.O.) sensing

edge input.

The CPS is for use with ancillary entrapment protection devices

only, and not used for primary monitored entrapment protection

devices.

CARTON INVENTORY

PART # DESCRIPTION QTY

CPS-U Photoelectric Sensors with Mounting Hardware 1

41K4629 Commercial Protector Interface 1

WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects

or other reproductive harm. For more information go to www.P65Warnings.ca.gov

INSTALLATION

ASSEMBLE AND MOUNT THE BRACKETS

The following instructions show recommended assembly of the

bracket(s) and “C” wrap based on the wall installation of the

photoelectric sensors on each side of the door or on the door

tracks themselves. There are also alternate mounting methods

which may ﬁ t your installation requirements better.

Make sure the wraps and brackets are aligned so the

photoelectric sensors will face each other across the door.

1 Fasten the “C” wraps to the mounting brackets having square

holes, using hardware shown.

WALL INSTALLATION

2 Connect each assembly to a slotted bracket, using the hardware

shown. Note alignment of brackets for left and right sides of

the door.

3 Finger tighten the lock nuts.

4 Use bracket mounting holes as a template to locate and drill

(2) 3/16" diameter pilot holes on both sides of the garage

door, 4-6 inches (10-15 cm) above the ﬂ oor. Do not exceed

6 inches (15 cm).

5 Attach bracket assemblies with 1/4"x1-1/2" lag screws.

6 Adjust right and left side bracket assemblies to the same

distance out from mounting surface. Make sure all door

hardware obstructions are cleared. Tighten the nuts securely.

DOOR TRACK INSTALLATION

2 Discard slotted bracket. Drill 3/8" holes in each track and fasten

securely with hardware .

Mounting Bracket

with Square Holes “C” Wrap

#10-32x3/8"

Screws

#10-32

Lock Nuts

1/4"x1-1/2"

Lag Screws

1/4"-20x12" Carriage Bolts

(with square shoulders)

1/4"-20

Lock Nuts

Mounting Bracket

with Slot

Mounting Bracket with

Square Holes

“C” Wrap

ALTERNATE WALL INSTALLATION ALTERNATE FLOOR INSTALLATION

Mounting Bracket

with Slot

Mounting Bracket

with Square Holes

“C” Wrap

Photoelectric Sensor with Wire

Indicator Light

Floor

Photoelectric Sensor with Wire

Inside

Wall Indicator Light

Mounting Bracket with

Square Holes

Mounting Bracket

with Slot

“C” Wrap

Floor

Attach with Concrete

Anchors (Not Provided)

“C” Wrap

Mounting Bracket with

Square Holes

1/4" Lock Nuts

Door Track

Drill 3/8" Holes

1/4"-20x1/2"

Carriage Bolts

Inside

Wall

Inside

Wall

Inside

Wall

INSTALLATION

MOUNT AND WIRE THE PHOTOELECTRIC SENSORS

1 Center each photoelectric sensor in the bracket with the lenses

pointing toward each other across the door.

2 Attach the photoelectric sensors to the brackets with the

provided hardware. Finger tighten the receiving sensor wing

nut. Securely tighten the sending sensor wing nut.

3 Run the photoelectric sensor wires to the operator. Fasten the

photoelectric sensor wires appropriately.

4 Connect the photoelectric sensor wires to the operator (refer to

CPS Wiring Connections, page 5).

Sensor Wire

Indicator Light

“C” Wrap

Wing Nut

1/4"-20x1-1/2" Hex Bolt

Photoelectric

Sensor

Photoelectric Sensor

6" (15 cm) max. above ﬂ oor

Photoelectric Sensor

6" (15 cm) max. above ﬂ oor

Invisible Light Beam

Protection Area

Sensor Wires

Connect Sensor Wire to Operator

(refer to CPS Wire Connections, page 5)

Especificaciones del producto

Marca:	Liftmaster
Categoría:	No categorizado
Modelo:	41K4629
Color del producto:	Zwart
Ancho:	140 mm
Profundidad:	150 mm
Altura:	86 mm
Interruptor encendido / apagado:	Ja
Certificación:	CB(62368+60950) / TUV / cTUVus / CE / FCC / BSMI / CCC / RCM / EAC / EAC RoHS / NOM
Destinado a:	PC
Certificados de sostenibilidad:	RoHS
Protección de voltaje de energía:	Over current, Over power, Over voltage, Overheating, Short circuit, Under voltage
Certificación 80 PLUS:	80 PLUS Bronze
Tiempo medio entre fallos (MTBF):	100000 uur
Los activos totales:	550 W
Factor de potencia:	0.99
Tipo de enfriamiento:	Actief
voltaje-de-entrada-de-CA:	100 - 240 V
Frecuencia-de-entrada-de-CA:	50 - 60 Hz
Diámetro del ventilador:	120 mm
Conector de alimentación de la placa base:	24-pin ATX
Factor de forma de fuente de alimentación (PSU):	ATX
Tecnología de rodamientos:	FDB
Número de conectores de alimentación SATA:	5
Tipo de cableado:	Niet-modulair
Conectores de alimentación PCI Express (6+2 pines):	2
Conector de alimentación EPS (4+4 pines):	Ja