Makita GD0811C Manual de Usario

Makita Máquina de molienda GD0811C

Lee a continuación 📖 el manual en español para Makita GD0811C (52 páginas) en la categoría Máquina de molienda. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/52

GB Die Grinder Instruction Manual

F Meuleuse droite Manuel d’instructions

D Geradschleifer Betriebsanleitung

I Smerigliatrice diritta Istruzioni per l’uso

Stempelslijpmachine

Gebruiksaanwijzing

E Rectificador Manual de instrucciones

P Retificadeira Manual de instruções

DK Ligesliber Brugsanvisning

GR Λειαντής Οδηγίες χρήσεως

TR Kalıp taşlama makinasıKullanma kılavuzu

GD0801C

GD0811C

1 2

3 4

5 6

015004 015009

015005 015006

015007 003495

015008

ENGLISH (Original instructions)

Explanation of general view

1 Lock-off lever

2 Switch lever

3 Speed adjusting dial

4 Side handle

5 Wrench 19

6 Wrench 13

7 Collet nut

8 Tighten

9 Loosen

10 8 mm (5/16") Max.

SPECIFICATIONS

• Due to our continuing program of research and

development, the specifications herein are subject to

change without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

ENE050-1

Intended use

The tool is intended for grinding ferrous materials or

deburring castings.

ENF002-2

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated and can, therefore, also be used from

sockets without earth wire.

GEA010-1

General Power Tool Safety Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and instructions for future

reference.

GEB034-9

DIE GRINDER SAFETY WARNINGS

Safety Warnings Common for Grinding Operation:

1. This power tool is intended to function as a

grinder. Read all safety warnings, instructions,

illustrations and specifications provided with

this power tool. Failure to follow all instructions

listed below may result in electric shock, fire and/or

serious injury.

2. Operations such as sanding, wire brushing,

polishing or cutting-off are not recommended to

be performed with this power tool. Operations for

which the power tool was not designed may create a

hazard and cause personal injury.

3. Do not use accessories which are not

specifically designed and recommended by the

tool manufacturer. Just because the accessory can

be attached to your power tool, it does not assure

safe operation.

4. The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and fly apart.

5. The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories

cannot be adequately controlled.

6. The arbour size of accessories must properly fit

the collet of the power tool. Accessories that do

not match the mounting hardware of the power tool

will run out of balance, vibrate excessively and may

cause loss of control.

7. Mandrel mounted accessories must be fully

inserted into the collet or chuck. If the mandrel is

insufficiently held and/or the overhang of the wheel

is too long, the mounted accessory may become

loose and be ejected at high velocity.

8. Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive

wheels for chips and cracks. If power tool or

accessory is dropped, inspect for damage or

install an undamaged accessory. After

inspecting and installing an accessory, position

yourself and bystanders away from the plane of

the rotating accessory and run the power tool at

maximum no-load speed for one minute.

Damaged accessories will normally break apart

during this test time.

Model GD0801C GD0811C

Collet size Max. 8 mm Max. 8 mm

Max. wheel point diameter

Max. wheel diameter 25 mm 50 mm

Max. mandrel (shank) length 40 mm 40 mm

Rated speed (n) / No load speed (n 0

) 29,000 min–1 7,000 min–1

Overall length 390 mm 390 mm

Net weight 2.0 kg 2.0 kg

Safety class /II

Especificaciones del producto

Marca:	Makita
Categoría:	Máquina de molienda
Modelo:	GD0811C

¿Necesitas ayuda?

Si necesitas ayuda con Makita GD0811C haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

Máquina de molienda Makita Manuales

Makita GA9060R Manual de Usario

14 Octubre 2024

Makita DGA700Z Manual de Usario

13 Octubre 2024

Makita GA022GD202 Manual de Usario

2 Octubre 2024

Makita GA7063RX02 Manual de Usario

2 Octubre 2024

Makita GA013GD101 Manual de Usario

2 Octubre 2024

Makita 9563 Manual de Usario

30 Septiembre 2024

Makita DGA513Z Manual de Usario

28 Septiembre 2024

Makita GA7062 Manual de Usario

24 Septiembre 2024

Makita XAG01Z Manual de Usario

22 Septiembre 2024

Makita GA7060R Manual de Usario

22 Septiembre 2024

Máquina de molienda Manuales

Últimos Máquina de molienda Manuales

Tryton TDS125B Manual de Usario

26 Octubre 2024

Chicago Pneumatic CP7255 Manual de Usario

26 Octubre 2024

Bosch GWS 18-150 PL Professional Manual de Usario

23 Octubre 2024

Parkside PEXS 270 A1 Manual de Usario

17 Octubre 2024

Parkside PWS 1010 Manual de Usario

17 Octubre 2024

Hikoki GP2S2 Manual de Usario

15 Octubre 2024

Hitachi G 13SR Manual de Usario

14 Octubre 2024

Milwaukee 2781-21 Manual de Usario

8 Octubre 2024

Metabo WP820-115 Manual de Usario

8 Octubre 2024

DeWalt DW887N Manual de Usario

6 Octubre 2024