Martin 516 Dimmer-Controller Manual de Usario

Martin No categorizado 516 Dimmer-Controller

Lee a continuación 📖 el manual en español para Martin 516 Dimmer-Controller (4 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/4
The Martin
516 Dimmer-Controller
users guide
CONTENTS
INTRODUCTION ................................................. 3
INSTALLING THE 516 DIMMER CONTROLLER . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
OPERATING WITH A MARTIN LIGHTING CONTROLLER . . . . . . . . . . . . . . . . . . . 4
DIP-SWITCH SETTINGS TABLE FOR THE 516 DIMMER-CONTROLLER . . . . . . . . 5
TECHNICALSPECIFICATIONS....................................... 5
INTRODUCTION
The Martin Professional enables the Martin range of intelligent516 Dimmer-Controller
lighting controllers to control analog lighting and smoke equipment which require a 0-10V
fader control voltage.
INSTALLING THE 516 DIMMER CONTROLLER
Your Martin Professional 516 Dimmer-Controller package comes complete with the following
items:
516 Dimmer-Controller.
5 metre XLR/XLR cable.
Users guide.
IMPORTANT
Before attempting any of the following please ensure that the units are
disconnected from any AC power.
Setting the supply voltage:
Located on the back of the controller is a mains voltage selector. You must set it so that it
matches your local mains voltage.
Fitting the mains plug:
The 516 Dimmer-Controller may be delivered without a plug on the mains lead. You will
need to t a suitable plug (one that ts your local mains socket) before you can connect it
to the mains. The double insulated mains lead on the 516 Dimmer-Controller contains three
wires. Connect the Brown wire to the LIVE-pin, the Blue wire to the NEUTRAL-pin and the
Yellow/Green wire to the EARTH-pin in the mains plug.
2
Connecting the 516 Dimmer-Controller to the Martin Serial Link:
The 516 Dimmer-Controller responds to information sent from any of the Martin Lighting
Controllers: 3032, 2032, 2308 or 2208. As far as the Lighting Controller is concerned, the
516 Dimmer-Controller is similar to any Martin Intelligent Lighting Unit (ie. Roboscan,
Robocolor, Robozap etc.). For this reason the 516 Dimmer-Controller will sometimes be
referred to as a Lighting Unit in the following text. Please use the following procedure to set
up the Martin Serial Link.:
Connect the rst lighting unit (which could be your 516 Dimmer-Controller) to your Martin
Lighting Controller (2208/2308/2032/3032) using the XLR/XLR or XLR/D-SUB cable which
came with the lighting controller.
If you are using one 516 Dimmer-Controller only, then insert the male XLR termination
plug, which came with your lighting controller, into the unused XLR socket on the 516
Dimmer-Controller.
If you are using other lighting units (Roboscans, Robocolors, Robozaps etc.) with the
lighting controller then connect these together with XLR/XLR cables like the one that
came with your 516 Dimmer-Controller. The last unit on the link should be terminated
with the male XLR termination plug. You may connect up to 32 units on the same link.
Using 516 Dimmer-Controllers only, this will give you 32 * 16 = 512 analog outputs.
Located on the back of the Dimmer-Controller is the address selection DIP-switch. Use
this switch to set your 516 Dimmer-Controller to the desired controller channel as
shown in the address setting table on page 4. Note that the 516 Dimmer-Controller
only requires one controller channel to control all 16 analog outputs.
Connecting the 516 Dimmer-Controller to your analog equipment:
Located on the back of the 516 Dimmer-Controller is a 25 pin D-SUB connector plus four
5 pin DIN sockets from which the analog output is provided. Use these to connect the 516
Dimmer-Controller to your analog equipment. The relation between channel numbers and
pin numbers is listed on the label located directly above the connectors.
Placing the 516 Dimmer-Controller:
The 516 Dimmer-Controller ts into any standard 19" rack. Alternatively, you can choose to
place the 516 Dimmer-Controller on its four rubber feet.
OPERATING WITH A MARTIN LIGHTING CONTROLLER
You may now switch on your 516 Dimmer-Controller followed by your Martin Lighting
Controller. Please refer to the users guide for your Martin Lighting Controller for further
operating instructions.
3

Especificaciones del producto

Marca: Martin
Categoría: No categorizado
Modelo: 516 Dimmer-Controller

¿Necesitas ayuda?

Si necesitas ayuda con Martin 516 Dimmer-Controller haz una pregunta a continuación y otros usuarios te responderán




No categorizado Martin Manuales

No categorizado Manuales

Últimos No categorizado Manuales