Maytag MER8600DS Manual de Usario

Maytag horno MER8600DS

Lee a continuación 📖 el manual en español para Maytag MER8600DS (16 páginas) en la categoría horno. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/16

INSTALLATION INSTRUCTIONS

30" (76 CM) FREESTANDING ELECTRIC RANGES

Table of Contents

RANGE SAFETY ..................................................................................2

INSTALLATION REQUIREMENTS.....................................................3

Tools and Parts.................................................................................3

Location Requirements.....................................................................3

Electrical Requirements - U.S.A. Only..............................................5

INSTALLATION INSTRUCTIONS.......................................................6

Unpack Range ..................................................................................6

Install Anti-Tip Bracket......................................................................6

Electrical Connection - U.S.A. Only..................................................8

Verify Anti-Tip Bracket Is Installed and Engaged...........................12

Level Range ....................................................................................13

Warming Drawer or Premium Storage Drawer...............................13

Storage Drawer ...............................................................................14

Oven Door .......................................................................................14

Complete Installation ......................................................................14

Moving the Range...........................................................................15

IMPORTANT:

Save for local electrical inspector's use.

W10403811C

RANGE SAFETY

You can be killed or seriously injured if you don't immediately

You can be killed or seriously injured if you don't follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation instructions.

Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed and engaged.

Failure to follow these instructions can result in death or serious burns to children and adults.

Anti-Tip

Bracket

To verify the anti-tip bracket is installed and engaged:

•Slide range forward.

•Look for the anti-tip bracket securely attached to floor or wall.

•Slide range back so rear range foot is under anti-tip bracket.

•See installation instructions for details.

Range Foot

WARNING

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

Parts supplied

Check that all parts are included.

■3 - 10-32 hex nuts (attached to terminal block)

■3 - Terminal lugs

■Anti-tip bracket must be securely mounted to floor or wall.

Thickness of flooring may require longer screws to anchor

bracket to floor.

Parts needed

If using a power supply cord kit:

■A UL listed power supply cord kit marked for use with ranges.

The cord should be rated at 250 volts minimum, 40 amps or

50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm)

diameter connection opening and must end in ring terminals

or open-end spade terminals with upturned ends.

■A UL listed strain relief.

Check local codes. Check existing electrical supply. See the

appropriate “Electrical Requirements” section.

It is recommended that all electrical connections be made by a

licensed, qualified electrical installer.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

■It is the installer’s responsibility to comply with installation

clearances specified on the model/serial rating plate. The

model/serial rating plate is located on the frame behind a top

corner of the door or either side of the drawer.

■To eliminate the risk of burns or fire by reaching over heated

surface units, cabinet storage space located above the

surface units should be avoided. If cabinet storage is to be

provided, the risk can be reduced by installing a range hood

that projects horizontally a minimum of 5" (12.7 cm) beyond

the bottom of the cabinets.

■Cabinet opening dimensions that are shown must be used.

Given dimensions are minimum clearances.

■The anti-tip bracket must be installed. To install the anti-tip

bracket shipped with the range, see “Install Anti-Tip Bracket”

section.

■Grounded electrical supply is required. See the appropriate

“Electrical Requirements” section.

IMPORTANT: To avoid damage to your cabinets, check with your

builder or cabinet supplier to make sure that the materials used

will not discolor, delaminate or sustain other damage. This oven

has been designed in accordance with the requirements of UL

and CSA International and complies with the maximum allowable

wood cabinet temperatures of 194° (90°C).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction

and Safety, Title 24, HUD Part 280). When such standard is not

applicable, use the Standard for Manufactured Home

Installations, ANSI A225.1/NFPA 501A or local codes.

Mobile home installations require:

■When this range is installed in a mobile home, it must be

secured per the instructions in this document.

■Four-wire power supply cord or cable must be used in a

mobile home installation. The appliance wiring will need to be

revised. See “Electrical Connection - U.S.A. Only” section.

■Tape measure

■Flat-blade screwdriver

■Phillips screwdriver

■Level

■Hammer

■Hand or electric drill

■Wrench or pliers

■Marker or pencil

■Masking tape

■¼" drive ratchet

■¼" nut driver

■³⁄₈" and ⁵⁄₁₆" nut driver

■¹⁄₈" (3.2 mm) drill bit (for

wood floors)

■Tin snips or large wire

cutters (for cutting ground

strap if necessary)

A. Anti-tip bracket

B. #12 x 1

⁵⁄₈

" screws (2)

Especificaciones del producto

Marca:	Maytag
Categoría:	horno
Modelo:	MER8600DS
Color del producto:	Zwart
Ancho:	46 mm
Profundidad:	35 mm
Altura:	65.5 mm
Certificación:	CE
Tensión de entrada nominal:	600 V
Diámetro del cable:	24 mm
Salida de corriente nominal:	100 A
Clase operativa:	3