Maytag W10606694 Manual de Usario

Maytag secadora W10606694

Lee a continuación 📖 el manual en español para Maytag W10606694 (28 páginas) en la categoría secadora. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/28

W10740674A

Installation Instructions

for W10606694 L.P. (Propane and Butane)

Gas Conversion Kit

Parts included in Kit:

1 Instruction Sheet

1 Blocking Pin

1 Orice, Burner-Butane No. .049

1 Orice, Burner-Propane No. 55

1 Label, Rating Plate Conversion (English)

1 Label, Rating Plate Conversion (French)

1 Label, Conversion Record (English)

1 Label, Conversion Record (French)

1 Label, Burner Baseplate (English/French)

Converting 20,000 BTU/hr Gas Burners from Natural Gas

to Liqueed Petroleum (Bottled Gas)

NOTE: A qualied service technician is any person or

representative of a company who is experienced or trained

in servicing gas equipment and is familiar with necessary

precautions.

IMPORTANT: The LP Conversion Kit you received is an

approved kit for converting your gas dryer from natural to LP

propane or butane gas. The kit number shown on the Burner

Data Label located on the Burner Base may not match the kit

you receive due to kit consolidation.

NOTE: Read these instructions before proceeding.

Canada Only

THIS CONVERSION KIT SHALL BE CARRIED OUT IN

ACCORDANCE WITH THE REQUIREMENTS OF THE

PROVINCIAL AUTHORITIES HAVING JURISDICTION AND

IN ACCORDANCE WITH THE REQUIREMENTS OF THE

CAN-B49.1 AND CAN1-B149.2 INSTALLATION CODE.

Warning: This conversion kit shall be installed by a qualied

service agency in accordance with the manufacturer’s

instructions and all applicable codes and requirements of

the authority having jurisdiction. The information in these

instructions must be followed to minimize the risk of re or

explosion or to prevent property damage, personal injury,

or death. The qualied service agency is responsible for the

proper installation of this kit. The installation is not proper

and complete until the operation of the converted appliance

is checked as specied in the manufacturer’s instructions

supplied with this kit.

This dryer has been manufactured for use with Natural Gas.

Installation of this conversion kit converts the dryer for use

with L.P. gas with supply pressure between 8" (203 mm) and

13" (330 mm) water column. If this dryer is converted for use

with L.P. gas by means of this kit, the input rating will be 20,000

BTU’s per hour, for altitudes up to 10,000 feet (3,048 m). For

installations above 2,000 feet (610 m), contact a qualied

service agency for derating instructions.

Preparing for Kit Installation

READ THOROUGHLY AND FOLLOW STEPS

1. Unplug dryer or disconnect power.

2. Turn off gas supply using the shut-off valve that supplies

the dryer.

3. Fill out information on the appropriate Conversion Record

Label (English or French) and apply in a conspicuous

location adjacent to model and serial tag located in the

door well. Go to Section 1, 2, or 3, depending on model.

Tools and Accessories required:

1/4" Socket and Ratchet Wrench

1/4" Nut Driver

5/16" Nut Driver

Phillips-Head Screwdriver

T-20 Torx®-head Screwdriver†

Pliers or Flat-Head Screwdriver

†® Torx and T-20 are registered trademarks of Acument Intellectual

Properties, LLC.

Disassembling the Dryer

Section

Cabinet

Width

Console

Location

Front Panel

Type

Rated

Capacity

(cubic feet)

Page

1 29" Rear Full 8.8+ 2

2 27" Front Full 7 to 7.5 4

3 29" Rear Full 7 to 7.6 8

4 27" Rear Toe Panel 7 to 7.5 9

Disassembling the Dryer

SECTION 1 – 8.8+ CUBIC FOOT MODELS WITH 29" CABINET,

FULL FRONT PANEL, AND REAR CONSOLE

To gain access to inside of dryer:

1. Remove console rear plate and rear shelf plate by

removing a total of eight (8) screws. See Figure 1.

2. Remove two (2) screws from the rear of the top.

See . This will allow the top to be slid rearwardFigure 2 .

3. Disconnect the door switch connector located in the top

left front corner of the dryer. See Figure 3.

4. Remove the front panel and door assembly by removing

a total of eleven (11) screws: Four (4) ¼" hex-head screws

along the bottom front, three (3) Phillips-head screws around

the door opening, and four (4) T-20 Torx-head screws on

the top front panel bracket. See . Once screws are Figure 4

removed, close the door and lift up the front panel and door

assembly to remove.

(3) SCREWS

FIGURE 1

FIGURE 2

FIGURE 3

FIGURE 4

5. Disconnect the drum light connector located in the top left

front corner of the dryer. See . Figure 5

FIGURE 5

(5) SCREWS CONSOLE

REAR

PLATE

REAR

SHELF

PLATE

(2) SCREWS

DOOR SWITCH

CONNECTOR

(3) SCREWS

(4) SCREWS

FRONT

PANEL

DRUM LIGHT

CONNECTOR

TOP

(4) SCREWS

6. Disconnect moisture strip connector located in lower right

front corner of the dryer. See Figure 6.

7. Remove the two (2) lower lint duct screws. See . Figure 6

8. Remove the four (4) screws from the two side edges of the

front bulkhead. See .Figure 7

9. Remove the front bulkhead and lint duct assembly by lifting

it off the two (2) front hooks (see ) and then lowering Figure 8

it to clear the drum support rollers from the drum front.

NOTE: Lift up on front of drum to help lift off of rollers on front

bulkhead.

NOTE: Since the drum belt is still in tension, it will pull the drum

down as you remove the front bulkhead and lint duct assembly.

10. Remove the drum belt tension by reaching into dryer

just under the drum to back side of drive motor. Grasp idler

pulley and lift up to relieve tension from belt and remove belt

from motor pulley and lower the idler slowly. See .Figure 9

FIGURE 6

FIGURE 7

FIGURE 8

FIGURE 9

LINT DUCT

(2) SCREWS

MOISTURE

STRIP

CONNECTOR

(4) SCREWS

FRONT

BULKHEAD

(2) BULKHEAD

HOOKS (ONE ON

EACH SIDE)

IDLER

PULLEY

MOTOR

PULLEY

DRUM

BELT

Especificaciones del producto

Marca:	Maytag
Categoría:	secadora
Modelo:	W10606694
Color del producto:	Zwart
Diámetro:	- mm
Longitud:	- mm
Compatibilidad:	PMW-EX1/PMW-EX1R/VCL-EX0877/PMW-EX1/EX1R
Distancia focal mínima (equivalente a película de 35 mm):	31.4 mm
Distancia focal máxima (equivalente a película de 35 mm):	439 mm
Aumento:	0.8 x
Tamaño del filtro:	- mm
Tipo de lente:	Groothoeklens
Componente para:	Camcorder