Metra 70-5519 Manual de Usario

Lee a continuación 📖 el manual en español para Metra 70-5519 (2 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/2
Receiver Wiring Adaptor
120 70-5519
Revision 03/27/14
*120705519*
STEP 1 -- CONNECT WIRES
Connect wires below to the matching
function of each wire on your receiver
(refer to instructions supplied with
receiver).
The wire colors of your new receiver may,
or may not, match the wire colors of the
adaptor. Match adaptor and receiver
wires by function, disregarding color.
If your receiver does not have a Dimmer or
Illumination wire, tape off the Orange wire.
Connect all Black and Black/White wires
together by soldering and taping or by
using a large crimp cap.
Individually tape off any unused wires.
Make final wiring connections following
instructions on the next page.
A.
White - Left Front Speaker Positive
Violet/Black - Right Rear Speaker Negative
Red - 12 Volts Switched Power
Violet - Right Rear Speaker Positive
Green - Left Rear Speaker Positive
Yellow - 12 Volts Constant Power
Gray - Right Front Speaker Positive
Gray/Black - Right Front Speaker Negative
Green/Black - Left Rear Speaker Negative
Orange - Illumination
White/Black - Left Front Speaker Negative
Black - Chassis Ground
Black - Amplifier Ground
Orange/Black - (not used, tape off)
Blue/White - Amplifier Turn-on
Black/White - Amplifier Ground
Subwoofer Input
Blue/White - Amplifier Turn-on
Black/White - Amplifier Ground
For best results, the White RCA plug should be
connected to the subwoofer preamp output on
the new receiver.
RED
WHITE
Center Channel Input
(Except for Mustang -
this is also a subwoofer
input for the Mustang)
Copyright 2014 Crutchfield Corporation
B.
C.
D.
E.
IMPORTANT
Before starting, compare items on your invoice with items
received. Thoroughly check packing materials. If an item
is missing, please call Crutchfield at 1-888-955-6000.
Blue/Red - Connects to both Blue/White
Wires on Amp/Sub harness
Black - Chassis Ground
Blue/White - Connects to Blue/White Amp Remote Wire from receiver
120AFDI5V Converter (packaged separately)
Receiver Wiring Adaptor Connections
120 70-5519
Page 2
STEP 2 -- CONTINUED
A. Strip wires back 1/2”.
B. Twist wires together and
insert in crimp cap.
C. Squeeze middle of cap
for tight connection.
Copyright 2014 Crutchfield Corporation
STEP 3 -- APPLICATION
When ready to install the receiver, plug
the Wiring Adaptor from the new receiver
or receiver assembly into the factory
radio harness(es) in the vehicle dash.
D. Complete crimp connections
for all necessary wires.
E. Be sure to wrap any wires from
the Wiring Adaptor that are
not necessary (wires with no
match from the new receiver)
with electrical tape.
STEP 2 -- CRIMP CONNECTIONS
Tools & Parts
Required
Wire Stripper/Crimp Tool Crimp Caps
Unused Wire (tape over bare wires)
Receiver Wiring Adaptor
Generic Illustration
Generic Illustration

Especificaciones del producto

Marca: Metra
Categoría: No categorizado
Modelo: 70-5519

¿Necesitas ayuda?

Si necesitas ayuda con Metra 70-5519 haz una pregunta a continuación y otros usuarios te responderán




No categorizado Metra Manuales

No categorizado Manuales

Últimos No categorizado Manuales