Metra 91-3037P Manual de Usario

Lee a continuación 📖 el manual en español para Metra 91-3037P (3 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/3
IMPORTANT
Installation Kit
120 91-3037P
Before starting, compare items on your invoice with items
received. Carefully check through packaging material.
If an item is missing, please call:
Crutchfield
Parts Supplied:
Kit Frame
Support Tray
Chevrolet/GMC
Revision 12/10/03
Kit assembly instructions are on the following pages.
Page 1 of 3
®
Copyright 2003 Crutchfield Corporation
*120913037P*
Mounting Brackets
(2) Studs (2) 3/8” Nuts
(4) 1/4” Hex Screws
Trimplate
at 1-888-955-6000
FIGURE 2
Shaft Supports
Installation Kit
120 91-3037P
1. Press posts on trimplate into holes on kit frame to snap
parts together and secure with hex screws (Figure 1).
2. Use a utility knife to cut out in trimplate to shaft supports
create a DIN opening (Figure 2).
3. Push clips on into slots on rear of kit frame to support tray
secure (Figure 1).
4. Cut off tabs on both mounting brackets labeled “B” and “C”
that are shown as shaded (Figure 3). The “A” tabs must
remain.
5. Secure mounting brackets to sides of kit frame with studs
and nuts supplied (Figure 1).
6. Remove DIN sleeve from receiver and slide into opening in
trimplate. Secure sleeve to trimplate by bending the securing
tabs (Figure 4).
7. Slide receiver into sleeve/kit assembly.
DIN Receiver Assembly
2
®
Copyright 2003 Crutchfield Corporation
Securing Tabs
DIN Sleeve
Bend tabs after sleeve
is inside assembly.
FIGURE 1
Trimplate
Kit Frame Support Tray
Left Mounting Bracket
Stud
Nut
Right Mounting Bracket
FIGURE 4
Hex Screws
Tools Required
Utility
Knife
Small Flat Blade
Screwdriver
1/4” & 3/8”
Sockets
Hacksaw
Chevrolet/GMC
FIGURE 3
Cut off
“B” & “C” tabs
(shaded)
“C”
“B”
“B”
“A” tabs remain
“A”
“A”
Installation Kit
120 91-3037P
Spacers
(supplied with
your order)
1. Press posts on trimplate into holes on kit frame to snap parts
together and secure with hex screws (Figure 1).
2. Push clips on into slots on rear of kit frame support tray
to secure (Figure 1).
3. Cut off tabs on both mounting brackets labeled “B” and “C”
shown as shaded (Figure 2). The “A” tabs must remain.
4. Secure mounting brackets to sides of kit assembly with
studs nutsand supplied (Figure 1).
5. Choose the proper spacers (supplied with your order) to
allow receiver nosepiece to extend 1/8” to 1/4” beyond face of
trimplate (Figure 3).
6. Insert receiver shafts (with spacers in place) through openings
in trimplate. Secure receiver and faceplate with shaftnuts
supplied with receiver.
7. Attach control knobs.
1/8” -1/4”
Spacer
Shaft Receiver Assembly
3
FIGURE 3
Shaftnuts
®
Copyright 2003 Crutchfield Corporation
FIGURE 1
Trimplate
Kit Frame
Support Tray
Left Mounting Bracket
Faceplate
Control Knobs
Tools Required
Deep Socket
(size depends upon receiver)
Stud
Nut
Right Mounting Bracket
1/4” & 3/8”
Sockets
Hex Screws
FIGURE 2
Cut off
“B” & “C” tabs
(shaded)
Chevrolet/GMC
“C”
“B”
“B”
“A” tabs must remain
“A”
“A”
Hacksaw

Especificaciones del producto

Marca: Metra
Categoría: No categorizado
Modelo: 91-3037P

¿Necesitas ayuda?

Si necesitas ayuda con Metra 91-3037P haz una pregunta a continuación y otros usuarios te responderán




No categorizado Metra Manuales

No categorizado Manuales

Últimos No categorizado Manuales