Metra 95-6556G Manual de Usario

Lee a continuación 📖 el manual en español para Metra 95-6556G (5 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/5
Metra. The World’s Best Kits.® MetraOnline.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 4/14/20 INST95-6556
I N S TA L L AT I O N I N S T R U C T I O N S
95-6556
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
KIT FEATURES
ISO DDIN radio provision
Painted to match the factory finish:
• 95-6556G - Gray
• 95-6556DK - Dark Khaki
KIT COMPONENTS
• A) Radio bezel • B) Radio brackets • C) Retaining caps • D) Philips screws (4)
TOOLS REQUIRED
• 9/32” Socket wrench • 5mm Allen screwdriver
• Cutting tool • Panel removal tool
• Phillips screwdriver • Solder gun
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation .......................................................3
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wiring Harness: CHTO-01
Antenna Adapter: 40-CR10
A B C D
Jeep Commander (without NAV) 2006-2007
Visit for more detailed information about the product and up-to-date vehicle MetraOnline.com
specific applications
386.257.1187
|
MetraOnline.com
2
1. Remove (16) 5mm Allen screws securing
the dashboard trim panel. (Figure A)
2. Unclip and remove the dashboard trim
panel. (Figure B)
3. Remove (4) 9/32” screws securing the
radio. Slide the radio out, then unplug
and remove.
Continue to Kit Preparation
DASH DISASSEMBLY
(Figure B)
(Figure A)
(4) screws (4) screws (4) screws (4) screws
REV. 4/14/2020 INST95-6556 3
From the factory dashboard trim panel:
1. Using either a solder gun or cutting tool,
remove the plastic welds holding the
factory radio bezel in place. (Figure A)
2. Using a pry tool, remove the factory
radio bezel from the center of the
factory dash panel.
Be sure to damage the holes Note: NOT
in the dash panel, so they can be used for
mounting the radio bezel in the next step
.
3. radio bezel Clip the in, then place the
retaining caps over the (4) screw holes.
Using a manual screwdriver, secure
using (4) Phillips screws provided.
(Figure B)
Continue to Kit Assembly
KIT PREPARATION KIT ASSEMBLY
(Figure A)(Figure A)
(Figure B)
1. Secure the radio brackets to the radio
using screws supplied with the radio.
(Figure A)
2. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using
the proper mating adapter from Metra
and/or Axxess. Test the radio for proper
operation.
3. Slide the radio into the dash, then
secure using the factory screws.
4.
Reinstall the dash in reverse order of
disassembly to complete the installation.

Especificaciones del producto

Marca: Metra
Categoría: No categorizado
Modelo: 95-6556G

¿Necesitas ayuda?

Si necesitas ayuda con Metra 95-6556G haz una pregunta a continuación y otros usuarios te responderán




No categorizado Metra Manuales

No categorizado Manuales

Últimos No categorizado Manuales