Metra 95-7353CH Manual de Usario

Lee a continuación 📖 el manual en español para Metra 95-7353CH (8 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/8
METRA. The World’s best kits.metraonline.com © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
REV. 7/29/2015 INST95-7353CH
Installation instructions for part 95-7353CH
CAUTION!
Metra recommends disconnecting the negative bat
-
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con
-
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
• ISO DDIN radio provision
Painted Charcoal
A) Radio housing trim panel • B) Radio brackets • C) Start/Stop switch blank plate
• D) Airbag light blank plate • E) (5) #8 x 3/8” Phillips truss-head screws
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-7304
Antenna Adapter: • Not required
• Panel removal tool • Phillips screwdriver • Socket wrench
TOOLS REQUIRED
Dash Disassembly ................................................. 2
Kit Preparation ....................................................... 3
Kit Assembly
ISO DDIN radio provision 3 ......................................
Table of Contents
A B C D E
95-7353CH
1. Unclip and remove the factory
radio trim panel including the a/c
vents. (Figure A)
Note: Remove the (8) retaining
clips to be reused in Kit Assembly.
2. Remove (4) Phillips screws
securing the radio in the dash.
3. Remove (2) Phillips screws
securing the start/stop switch if
equipped. (Figure B)
Dash Disassembly
(Figure A)
4.
Remove (4) Phillips screws securing
the storage pocket (Figure B)
5. Remove the (8) Phillips screws
securing the a/c vents then unclip
and remove them from the radio
trim panel. (Figure B)
6. Unclip and remove the hazard
switch. (Figure B)
7. Remove (3) Phillips screws
securing the passenger air bag
indicator. (Figure B)
Continue to kit preparation
(Figure B)
Step 3
Step 4
Step 5
Step 6
Step 7
95-7353CH
Kit Preparation Kit Assembly
(Figure A)
ISO DDIN radio provision
1. Mount the radio to the radio
brackets using the screws supplied
with the radio. (Figure A)
2. Mount the radio/bracket assembly
into the dash.
3. Locate the factory wiring harness
in the dash. Metra recommends
using the proper mating adapter
from Metra or AXXESS. Re-connect
the negative battery terminal and
test the radio for proper operation.
4. Reassemble the dash in reverse
order of disassembly.
1. Mount the a/c vents, storage pocket,
hazard switch, and passenger air
bag indicator into the Radio Housing
Trim Panel using screws removed in
disassembly. (Figure A)
Note: For models without an airbag light,
a blank plate and (3) #8 x 3/8” Phillips
Truss-Head Screws are provided.
2. Mount the start/stop switch or blank
plate depending on your application
into the Radio Housing Trim Panel.
Note: If no switch is present there are
(2) #8 X 3/8” Phillips truss head screws
supplied to mount the blank plate.
3. Install the (8) panel clips removed
in disassembly onto the Radio
Housing Trim Panel.
Continue to kit assembly
(Figure A)
Note: An airbag-light
blank plate and screws
are included for
non-US models.

Especificaciones del producto

Marca: Metra
Categoría: No categorizado
Modelo: 95-7353CH

¿Necesitas ayuda?

Si necesitas ayuda con Metra 95-7353CH haz una pregunta a continuación y otros usuarios te responderán




No categorizado Metra Manuales

No categorizado Manuales

Últimos No categorizado Manuales