Metra 99-3009C Manual de Usario

Lee a continuación 📖 el manual en español para Metra 99-3009C (5 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/5
IMPORTANT
Installation Kit
120 99-3009
Before starting, compare items on your invoice with items
received. If any parts are missing, first carefully check through
packaging material. If an item is missing, please call:
Crutchfield
Parts Supplied:
Receiver Mounting Bracket
Spacer Ring
Chevrolet/Pontiac
Revision 04/13/00
Kit assembly instructions are on the following pages.
Receiver Trimplate
(2) Shaft Tabs
(1) Cariage Bolt
Page 1 of 5
*120993009*
®
Copyright 1999 Crutchfield Corporation
(1) Hex Nut
The carriage bolt and nut are used only in Camaros.
at 1-888-955-6000
Installation Kit
120 99-3009
Chevrolet/Pontiac
DIN Assembly - Firebird & Camaro
See page 4 for Grand Prix DIN assembly.
1. Using a utility knife, cut out shaft
supports to create the DIN opening
as shown (Figure 1).
2. Remove DIN sleeve and trim ring
from receiver if in place.
3. Slide DIN sleeve into receiver
mounting bracket and secure by
bending securing tabs (Figure 2).
4. Slide receiver fully into sleeve and
install trim ring.
5. Install assembly following instructions
in the Mastersheet for your particular
vehicle.
Page 2
Receiver Mounting Bracket
DIN Sleeve
FIGURE 1
FIGURE 2
®
Copyright 1999 Crutchfield Corporation
Tools Required
Flat Blade
Screwdriver
Utility Knife
Securing Tabs
Bend tabs after sleeve
is inside mounting bracket.
Trim Ring
Note for Firebird installations only:
Prepare kit as shown in the Inset, then
proceed with the following steps.
INSET
For 1993 Firebirds:
Break off this shaded
tab.
For 1994 Firebirds:
Break off both shaded
tabs.
Shaft Supports
Use these tabs
for 93-95 Camaros
Shaft Tabs
Installation Kit
Tools Required
120 99-3009
Deep Socket
(size depends
upon receiver)
Shaftnuts
(supplied with receiver)
1. Choose the proper spacers (supplied with
your order) to allow receiver nosepiece to
extend 1/8” to 1/4” beyond face of receiver
mounting bracket (Figure 1).
2. Insert spacer ring in receiver mounting
bracket. Secure receiver, trimplate (with
shaft tabs inserted) and faceplate to
mounting bracket with spacers and
shaftnuts as shown.
3. Attach receiver control knobs.
4. Install assembly following instructions in the
Mastersheet for your particular vehicle.
Faceplate
Receiver Mounting Bracket
Shaft Assembly - Firebird & Camaro
See Page 5 for Grand Prix Shaft Assembly.
Page 3
1/8” - 1/4”
Spacer
®
Copyright 1999 Crutchfield Corporation
Spacers (supplied with
your order)
Control Knobs
Chevrolet/Pontiac
Note for Firebird installations only:
Prepare kit as shown in the Inset, then
proceed with the following steps.
INSET
For 1993 Firebirds:
Break off this shaded
tab.
For 1994 Firebirds:
Break off both shaded
tabs.
FIGURE 1
Trimplate
Spacer Ring
Use these tabs
for 93-95 Camaros

Especificaciones del producto

Marca: Metra
Categoría: No categorizado
Modelo: 99-3009C

¿Necesitas ayuda?

Si necesitas ayuda con Metra 99-3009C haz una pregunta a continuación y otros usuarios te responderán




No categorizado Metra Manuales

No categorizado Manuales

Últimos No categorizado Manuales